Need Help?
Call or text
Rear drum bearing kit supports and smoothly rotates your dryer drum. Replace when you hear squealing, screeching, or grinding noises. Verify fit with your model.
Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more
The Idler Pulley is an OEM part for GE dryers. This critical component helps to maintain the correct tension on the dryer's drive belt, ensuring smooth operation and preventing it from slipping.
Symptoms of a bad Idler Pulley include:
Connects motor to drum for rotation. Replace if dryer won't start, makes noise, or drum doesn't turn. Confirm fit with your model number before ordering.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, prevent
Secures the blower wheel to the motor shaft. Replace when the wheel loosens or moves, causing rattling or rubbing noise. Includes clamps and screw.
Had to remove the front and top panel on the dryer, disconnect the belt and remove the drum. From there it was two screws to slide out the motor assembly with the fan attached and one bolt to remove the clamp and screw kit holding the fan in place. They kit was worn and was allowing the fan to move forward and back on the motor shaft. Once replaced it took about 5 minutes to reassemble and my dryer now purs like a kitten. Read more
This dryer motor kit powers the drum and blower. Replacing a weak or failed motor restores proper tumbling and airflow so the dryer starts reliably and dries loads more evenly.
Replaced the motor with a new one, if I can offer any advice about doing this job, make sure to keep track of where each wire goes on the motor and whatever wires need to be disconnected. There are a few good video's online showing how to do this job and can save you a lot of time and frustration. Read more
Bearing only, to get complete assembly order WE25M40
Dryer not heating? This heating element assembly restores heat when coils burn out. Straightforward DIY repair with basic tools in 1-2 hours.
With a screwdriver and some mechanical aptitude. Nothing harder that a few screws to change the parts. Read more
Seals the gap between drum and bulkhead in your dryer. Replace when worn to eliminate scraping noises, prevent fabric snags, and maintain airflow.
I cut power to the dryer. I removed the face of the dryer. I then removed the felt mounts beneath the drum. I removed the old strips of felt and cut the new seal to fit both mounts. I then remounted the felt mounts and replaced the face. Read more
Fixes dryer not heating or overheating issues. This safety thermostat monitors temperature and cuts power when too hot. Basic DIY repair, 30 minutes.
Adjustable
Installed the missing legs. Very east to do Read more
Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.
Watched the repair video. Saw what to look for. Found the dryer drum front support was broken and the slide bearings were worn. Replaced these items. Read more
Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.
Size: 8-32 t. Includes 12 screws.
Package of 12
Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.