Lwhw0050pq Parts

The Thermistor Assembly is an OEM part for LG air conditioners. It is typically located near the evaporator coil or in the air intake area of the unit. It measures the ambient temperature and sends signals to the control board to adjust the cooling output accordingly.

Causes of a faulty or malfunctioning thermistor assembly can include normal wear and tear, exposure to extreme temperatures, or electrical issues. These factors can lead to inaccurate temperature readings, improper cooling performance, or erratic behavior of the air conditioner.

Symptoms of a bad thermistor assembly may include:

• Inconsistent cooling or insufficient cooling
• Inaccurate temperature display on the control panel
• Frequent cycling on and off of the compressor

This OEM LG part can also be used on Kenmore/Sears appliances. 

Replace a missing or damaged installation kit with this Install Part Assembly. Designed for select air conditioners, it helps secure and seal the unit during setup for a stable fit and reliable performance.

• Provides the correct mounting/finishing components needed for proper installation
• Helps seal the opening to minimize air leaks and reduce vibration/noise
• Restores secure, stable support of the chassis during and after install
• Symptoms indicating replacement: incomplete installation, loose fit, rattling, or drafts around the unit

• Disconnect power before beginning; use two people to lift and support the unit
• Follow the model's installation instructions carefully
• Inspect the opening/sleeve; install level and tighten all fasteners securely
• After installation, verify a tight perimeter seal and stable, rattle-free operation

This installation kit includes the manufacturer-specified hardware used to secure and align an appliance during setup. Use it to replace missing or damaged install hardware and restore a safe, stable, factory-correct fit in the opening. What it does:

• Provides required mounting hardware for proper installation
• Helps prevent shifting, rocking, or tipping when the appliance is used
• Aids in correct alignment and spacing within the cabinet/opening
• Replaces lost or damaged original install parts

• One installation kit

• Disconnect power (and gas/water, if applicable) before starting
• Follow your model's installation instructions for bracket locations and fasteners
• Use appropriate anchors for wall/floor material as specified by the manufacturer
• After installation, verify the unit is level and securely anchored

This remote controller assembly replaces a malfunctioning TV remote control PCB and housing to restore infrared/IR command transmission and on-unit button control. Ideal when the remote stops responding or buttons become unresponsive. What it does:

• Replaces the internal PCB and button assembly that sends IR signals to the TV.
• Restores remote control functions like power, volume, channel, and input selection.
• Helps resolve symptoms such as no response from the remote, intermittent commands, or stuck/non-working buttons.
• Works with the existing remote cover and batteries if those components are reused.

• Disconnect power to the TV and remove batteries from the remote before replacing the assembly.
• Use appropriate small screwdrivers and keep track of screws and clips; handle the PCB by its edges to avoid damage.
• Reassemble carefully, insert fresh batteries, and test all functions after installation.

This isolator routes microwave energy between the magnetron and waveguide to help protect components and maintain consistent heating performance. Replacing a failed isolator can restore reliable cooking and help prevent further high-voltage damage. What it does:

• Directs RF energy from the magnetron into the waveguide/cavity
• Helps protect the magnetron by reducing reflected energy
• Aids in preventing arcing or burn damage in the waveguide area
• Common symptoms of failure: no heat or uneven heating, loud humming/buzzing, visible arcing/burn marks near the waveguide

• 1 isolator

• Disconnect power and discharge the high-voltage capacitor before servicing; risk of electric shock
• Handle waveguide components carefully; avoid contaminating RF surfaces and note exact orientation
• Take photos of the original setup to match positioning and fastener locations

Restore full remote control function with this replacement remote controller assembly. Replaces a damaged or unresponsive remote PCB and button cluster so the unit responds reliably to power, volume, input and menu commands. What it does:

• Replaces the internal circuit board and button interface that transmit IR/remote signals.
• Fixes symptoms like unresponsive or intermittent buttons, no power or no signal from the remote.
• Restores control of common functions such as power, volume, input selection and menu navigation.
• Useful when buttons are stuck, the remote was dropped, or the internal electronics are damaged.

• Remove batteries and disconnect power from the appliance before replacing the assembly.
• Handle the PCB by its edges to avoid damage from static or oils; keep small screws and clips organized.
• Reassemble the remote housing carefully to avoid pinching ribbons or misaligning buttons.

This blower is the rotating wheel that moves air through the dryer to support proper drying and venting. Replacing a worn or damaged blower restores airflow for more efficient, consistent drying performance. What it does

• Spins to pull air from the drum through the heater and out the vent
• Restores normal airflow when a blower wheel is cracked, broken, or missing fins
• Helps reduce long dry times, overheating, or unusual noises caused by a failing blower
• Works with the dryer motor and housing to maintain proper ventilation

• One blower wheel

• Disconnect power to the dryer before starting any repair
• Access typically requires removing the dryer front or rear panel and detaching the drum or blower housing
• Inspect the motor shaft and mounting hardware; replace any worn fasteners or bearings as needed

This power cord assembly provides the main AC connection for your appliance so it can receive reliable power. Replacing a damaged cord restores safe, consistent power delivery and reduces risk of intermittent operation or electrical hazards. What it does:

• Supplies AC power from the outlet to the appliance's internal power input
• Replaces frayed, cracked, or damaged wiring that can cause intermittent power or failure to start
• Helps eliminate loose or corroded connector issues that produce sparks, arcing, or burning smells
• Restores a secure, factory-style connection when the original cord is worn or broken

• Disconnect the appliance from power at the outlet before servicing
• Route the cord and secure strain relief exactly as the manufacturer specifies to avoid pinching
• Inspect connectors and terminals for damage; replace the entire assembly if terminals are corroded or insulation is compromised

This NTC thermistor assembly senses temperature and sends readings to the control board so the appliance maintains the correct cooling cycle. It replaces a failed or intermittent temperature sensor to restore proper temperature regulation. What it does:

• Measures compartment temperature and relays the signal to the control board
• Helps the appliance decide when to run compressor and fans for stable cooling
• Commonly replaces units that cause incorrect temperature readouts, excessive frost, or compressor cycling
• Works as the OEM temperature-sensing element in the appliance's refrigeration system

• Disconnect power before accessing internal components to avoid shock
• Handle sensor and wiring gently; avoid bending or crimping the thermistor tip
• Verify connector seating and routing to prevent pinched wires or interference with moving parts

This replacement electric capacitor helps stabilize voltage for appliance motors and control circuits, restoring reliable starts and smoother operation. Use it to replace a worn or failed capacitor to address motor-related performance issues. What it does:

• Stores and releases electrical charge to help motors start and run smoothly
• Stabilizes voltage to reduce surges that can affect control circuits
• Common symptom: motor hums but won't start or runs weakly
• Common symptom: intermittent operation or frequent tripping of breakers/fuses
• Can fail over time from heat, age, or repeated starts

• Always disconnect power to the appliance before servicing
• Discharge capacitor terminals before touching to avoid shock
• Observe terminal orientation and wiring; replace with identical type/ratings

This air filter assembly helps keep interior air fresh by capturing odors and airborne particles in compatible LG appliances. It replaces a worn or dirty filter assembly so the appliance can maintain cleaner-smelling air. What it does:

• Houses the replaceable filter media that helps reduce odors and common airborne particles
• Restores proper airflow through the appliance's air-cleaning path when worn or clogged
• Helps maintain a fresher-smelling interior environment between service intervals
• Serves as the factory replacement component designed to match original fit and function

• Disconnect power to the appliance before accessing internal components.
• Handle the assembly carefully to avoid damaging the filter media or housing.
• Follow the appliance manufacturer's instructions for removing and installing the assembly.
• Replace periodically or when performance declines; dispose of used filter media per local regulations.

This compressor isolator is a rubber mount that cushions and reduces vibration and noise from the compressor, helping keep the appliance quieter and preventing metal-to-metal contact. What it does:

• Dampens compressor vibration to reduce noise and rattling
• Helps prevent compressor movement that can strain mounting hardware
• Reduces transfer of vibration to the cabinet and surrounding components
• Commonly replaced when vibration noise or scraping is heard from the base

• One compressor isolator (rubber mount)

• Disconnect power to the appliance before any service and work with the appliance unplugged
• Access may require tilting or moving the appliance; use safe lifting practices and get help if needed
• Inspect surrounding mounts and hardware; replace like-for-like and verify fit before final assembly