Sgm364s Parts

This spill gasket seals the gap between the cooktop surface and the underlying spill tray, helping contain liquids and crumbs so they don't seep into the burner box. Replacing a worn gasket protects internal components and supports reliable ignition. What it does:

• Creates a perimeter seal to contain spills on the cooktop surface
• Helps prevent moisture and debris from reaching igniters and wiring
• Reduces seepage into the burner box/spill tray area
• Common signs include visible cracks or flattening, liquids leaking below the top after spills, and prolonged igniter clicking after cleaning or spills

• Spill gasket

• Disconnect power and shut off gas supply before servicing
• Remove grates, burner caps, and top as needed to access the old gasket
• Clean mating surfaces; install the new gasket without stretching and seat evenly with no gaps
• Reassemble and restore utilities; check for leaks per manufacturer guidance

This brass nut secures a threaded connection within the burner/manifold area of compatible cooking appliances, helping restore a tight, reliable attachment. Replace a worn or missing nut to keep fittings properly fastened and operating as designed.

• Secures a threaded fitting or tube connection on the burner/manifold assembly
• Helps maintain a tight, reliable joint when installed correctly
• Replaces a stripped, rounded, cracked, or missing nut
• Can address a loose connection that will no longer tighten

• Disconnect power and shut off the gas supply before servicing; allow all surfaces to cool
• Start threads by hand to avoid cross-threading
• Use a backup wrench on the mating fitting to prevent twisting or kinking tubing
• Do not overtighten; after reassembly, perform an approved leak-check before returning to service

A replacement service burner ring that restores proper burner alignment and appearance on compatible gas cooktops and ranges. Keeps the burner assembly seated correctly for consistent ignition and safe operation. What it does:

• Replaces a cracked, warped, or corroded burner ring to restore correct burner positioning
• Helps maintain proper flame shape and stable ignition at the burner head
• Can reduce visible damage and improve cooktop appearance after wear or impact
• Designed for use with compatible Samsung gas cooktops and ranges

• Turn off the gas supply and let the cooktop fully cool before servicing
• Remove grates and burner caps, then lift out the old ring before installing the replacement
• Inspect burner ports and ignition components for damage or debris while servicing

This blue indicator light restores the appliance's status illumination in the control area. Replace it if the original light is dim, flickering, or no longer illuminates so you can quickly see when a function is active.

• Provides a blue visual indication of operation/status on the control panel
• Helps at a glance when a feature is on
• Common fix for a light that won't turn on, is dim, flickers, or is physically damaged
• Direct-fit service part designed to connect to the original wiring and mounting points

• Disconnect power at the breaker or unplug the appliance before service
• Allow nearby surfaces and components to cool
• Access the indicator light from the control area; remove panels as needed
• Move connectors one at a time and route wiring as originally installed; test before reassembly

This large burner cap sits above the gas burner head on your range or cooktop. It shapes the flame and shields the burner from spills, promoting even heating and easier cleanup.

• Sits on the burner head to shape and distribute the flame evenly
• Helps protect the burner from drips, debris, and corrosion
• Replace if chipped, warped, or missing to correct hard-to-light or uneven/yellow flames
• Ensures proper simmering and consistent heat when seated level and centered

• Turn off gas and allow the cooktop to cool completely before servicing
• Clean and dry the burner head and seating surface
• Align and center the cap on locator pins; ensure it sits flat and stable
• Test ignition and flame pattern; reseat if the flame is uneven

This medium burner cap sits on top of the gas burner head to shape an even, stable flame and shield the head from spills and debris. Replacing a damaged or missing cap helps restore consistent ignition and heat distribution.

• Directs and spreads the flame evenly across the burner head for proper cooking performance
• Helps protect burner ports from drips, grease, and debris that can affect flame quality
• Supports reliable ignition when correctly centered and seated
• Common symptoms: uneven or yellow flames, delayed ignition, fluttering flame, or a chipped/warped/missing cap

• Allow the cooktop to cool completely and verify all controls are OFF
• Lift off the old cap; clean and dry the burner head and ports before installing
• Center the new cap on the matching medium burner head so it sits level and flush
• Light the burner to test; if the flame is uneven or yellow, turn off, let cool, and reseat the cap until the flame is steady and blue

This 5-point spark electrode kit replaces the igniter module and electrode assembly that creates sparks to light gas burners, restoring reliable ignition and stopping intermittent sparking or no-ignite conditions. What it does:

• Generates timed sparks to ignite gas burners when the control calls for heat
• Replaces worn or cracked electrodes that can cause weak or no spark
• Fixes symptoms like continuous clicking, one or more burners failing to light, or intermittent ignition
• Works as the central spark module and electrode harness for multi-burner gas ranges

• Disconnect power and shut off the gas supply before servicing
• Handle ceramic/porcelain electrode tips carefully to avoid cracking
• After installation, restore power/gas and test each burner for proper ignition

This service switch set is the control-panel switch assembly used to enable the appliance's diagnostic or service mode, letting technicians run built-in tests and troubleshoot electronic controls. It restores the ability to access service functions from the control interface. What it does:

• Enables the appliance's diagnostic/service mode so test routines and error checks can be run
• Replaces a worn, stuck, or non-responsive service/test switch that prevents entering diagnostics
• Helps confirm control board and sensor operation during troubleshooting
• Useful when the control panel does not respond to service-mode key sequences

• One service switch set

• Always disconnect power to the appliance before beginning any repair
• Access typically requires removing the control panel or console; refer to service manual for steps
• Handle the switch and wiring gently to avoid damaging connectors or ribbon cables

This burner ring replaces a damaged or worn stovetop burner ring to restore even flame distribution and a secure fit for the burner cap. It's a direct-replacement part designed for compatible Samsung gas cooktops. What it does:

• Provides the ring surface that channels gas flames around the burner cap for proper cooking heat
• Restores stable flame pattern and ignition reliability when cracked, warped, or corroded
• Helps prevent flame blowout and uneven heating caused by damaged rings
• Compatible surface design ensures correct alignment with the burner base and cap

• Turn off gas supply and unplug the appliance before servicing; follow all safety precautions
• Allow the cooktop to cool completely before attempting replacement
• Remove burner cap and existing ring, then set the new ring in place and reassemble in reverse order

This complete surface burner head assembly replaces a worn or damaged burner on compatible Samsung gas cooktops and ranges. Reinstates proper flame shape and stable operation so burners heat cookware reliably. What it does

• Directs and shapes the gas flame for even heat across cookware
• Replaces damaged or corroded burner ports that cause uneven cooking
• Can resolve weak, flickering, or irregular flames and ignition issues
• Works as the finished assembly—no additional burner cap required when listed as complete

• Turn off the gas supply and electrical power to the appliance before beginning service.
• Allow the cooktop to cool completely and remove burner grates/caps per your model's instructions.
• Reinstall by aligning the head on the valve stem and securing per manufacturer orientation; avoid overtightening.
• After installation, check for proper ignition and perform a gas-leak test.

This service top frame is the upper structural trim that supports and secures the control area and top panel, restoring fit and finish for a clean, stable appliance top. Designed for direct replacement to fix broken or warped tops. What it does:

• Replaces a cracked, bent, or damaged top frame to restore proper alignment and appearance
• Secures the control console and top panel to prevent gaps, rubbing, or rattling
• Helps maintain proper seal and fit between the top and cabinet, reducing air gaps and debris entry
• Matches original mounting points for a straightforward fit with factory hardware

• Disconnect power to the appliance before beginning any repair
• Remove the control console and any attached trim to access top frame mounting screws
• Align the replacement frame with factory mounting points and secure with original screws

This service wiring harness connects the appliance control board to internal components, restoring proper electrical signals and component operation. It's used to replace damaged or worn wiring that can cause intermittent faults or component failure. What it does:

• Provides factory-style wiring connections between the control board and components
• Restores power and signal paths for affected circuits
• Helps resolve intermittent operation, failure to start, or components not responding
• Prevents arcing and poor connections when original wires or terminals are damaged

• Disconnect power before beginning any repair to avoid shock or damage
• Handle connectors by the housings; avoid pulling on wires
• Route and secure the harness following original wire paths and strain-relief points
• If terminals or connectors are corroded or melted, replace them and ensure all connections are tight

This burner control knob replaces a worn or missing knob on your cooktop. It attaches to the burner valve stem so you can set flame levels smoothly and accurately, while restoring the original look with the printed logo. What it does:

• Mounts to the burner valve stem to adjust heat output
• Provides a secure grip and pointer for setting positions
• Common signs it's needed: cracked knob, stripped/split insert, knob falls off or spins freely
• Helps restore consistent burner control and appearance

• One control knob with logo

• Turn all burners off and allow the surface to cool; disconnect power to the appliance before servicing
• Pull the old knob straight off the stem
• Align the flat/keyed sides and push the new knob straight on until fully seated
• Verify smooth rotation and correct pointer alignment with the panel markings

This small burner cap covers the gas burner head on your cooktop to shape and protect the flame. Replacing a worn, cracked, or missing cap restores even heat distribution and reliable ignition for consistent cooking results.

• Sits over the burner head to distribute flame evenly and stabilize heat
• Shields the burner from spills and debris that can affect performance
• Proper seating supports quick, consistent ignition
• Common signs it's needed: uneven or yellow flames, difficulty lighting, or a damaged/missing cap

• Ensure all controls are off and the cooktop is completely cool
• Lift off the old cap; clean and dry the burner head surface
• Place the new cap on the matching small burner, centered and fully seated
• Light the burner to confirm an even, steady flame; reseat if necessary