Dde7500galwh Parts

Best Seller

Genuine Ge part

Rear Drum Bearing Kit

By: Ge

Part Number: WE25M40

The Rear Drum Bearing Kit is an OEM replacement part for GE dryers. It is a comprehensive kit that includes both rear drum bearings and necessary mounting hardware. These bearings play a vital role in smoothly rotating the dryer drum during cycles, reducing vibrations and noise.

Symptoms of bad bearings include:

Excessive shaking or vibrating during cycles
Loud grinding or scraping noises emanating from the rear drum area
Difficulty turning or rotating the dryer drum by hand
Increased wear and early failure of other components

Causes of bad bearings can include normal wear and tear over time, exposure to excessive loads or unbalanced loads that strained the bearings, or damage from extended use without proper lubrication.

This OEM replacement is also compatible with Hotpoint, RCA, and some Kenmore models.

This part fixes the following symptoms

Noisy

Do-It-Yourself Stories from Customers like You Very loud squeal noise Thomas P. • Dundalk , MD • June 05, 2018

Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more

$73.95

Compare At:: $88.74
You Save:: $14.79

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Dryer Drive Belt

4.9 (257)

By: Ge

Part Number: WE12X10014

The Dryer Drive Belt is an OEM part for GE dryers that connects the motor to the drum, allowing the drum to rotate during the drying cycle. The belt measures approximately 87 inches long and 0.25 inches wide, with 4 ribs.

Over time, the Dryer Drive Belt can wear out or break, leading to the drum not turning.

Symptoms of a bad Dryer Drive Belt include:

The drum not spinning or rotating
A squealing or thumping noise coming from the dryer
The dryer stopping unexpectedly during a cycle

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This part fixes the following symptoms

Will not tumble
Won't start
Noisy

Do-It-Yourself Stories from Customers like You Was making a squeaking/squealing on start up Gerald G. • Nashua , NH • March 20, 2016

My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more

$15.38

Compare At:: $27.08
You Save:: $11.70

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Door Latch

5.0 (28)

By: Ge

Part Number: WE1M1011

The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance.

Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching.

Symptoms of a bad Door Latch include:

The dryer door doesn't stay closed during cycles.
Difficulty in starting the dryer due to the door not activating the safety switch.
Visible wear or damage to the latch mechanism.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This part fixes the following symptoms

Door won't close

Do-It-Yourself Stories from Customers like You Was making a squeaking/squealing on start up Gerald G. • Nashua , NH • March 20, 2016

$10.95

Compare At:: $13.14
You Save:: $2.19

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Clamp And Screw Kit

5.0 (22)

By: Ge

Part Number: WE1X688

The GE clamp and screw kit is an OEM replacement part responsible for securing the dryer blower wheel in place. This kit consists of two clamps and a screw, designed to ensure the blower wheel remains firmly attached to the motor shaft. The clamp maintains the blower wheel's stability and prevents it from coming loose during the drying process. The blower wheel creates the airflow necessary to circulate hot air and efficiently dry clothes.

Over time, clamps and screws can become loose or corroded due to regular use, vibrations, or exposure to moisture. Improper handling during maintenance or repairs can also lead to damage or loss of these small but essential parts.

Symptoms of a bad Clamp and Screw Kit include:

Loose or rattling components within the dryer
Parts becoming misaligned or detached
Unusual noises during dryer operation
Difficulty in securing dryer parts during repairs

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Do-It-Yourself Stories from Customers like You Blower fan had come loose and was hitting the inside of the housing Chris R. • Ridgeland , MS • February 08, 2015

Had to remove the front and top panel on the dryer, disconnect the belt and remove the drum. From there it was two screws to slide out the motor assembly with the fan attached and one bolt to remove the clamp and screw kit holding the fan in place. They kit was worn and was allowing the fan to move forward and back on the motor shaft. Once replaced it took about 5 minutes to reassemble and my dryer now purs like a kitten. Read more

$18.52

Compare At:: $22.04
You Save:: $3.52

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Dryer Motor Kit

4.7 (21)

By: Ge

Part Number: WE17X10010

This dryer motor kit powers the drum and blower. Replacing a weak or failed motor restores proper tumbling and airflow so the dryer starts reliably and dries loads more evenly.

Drives the drum via the belt and turns the blower wheel for airflow
Helps resolve: dryer hums but won't start, drum won't turn, or stops mid-cycle
Can reduce loud buzzing/grinding noises from the motor area
Restores consistent operation when the motor overheats and trips its protector

What's included: 1 drive motor Install notes:

Disconnect power; turn off gas supply to gas dryers before servicing
Remove panels to access the drive system; release belt tension and remove the drum as needed
The blower wheel threads onto the motor shaft—support it carefully; many GE dryers use a reverse (left-hand) thread
Transfer wiring and any reusable hardware to the new motor; test before reassembly

Do-It-Yourself Stories from Customers like You Motor was not working Linn C. • Saint Augustine , FL • June 17, 2014

Replaced the motor with a new one, if I can offer any advice about doing this job, make sure to keep track of where each wire goes on the motor and whatever wires need to be disconnected. There are a few good video's online showing how to do this job and can save you a lot of time and frustration. Read more

$156.51

Compare At:: $283.68
You Save:: $127.17

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Rear Drum Support Bearing

4.9 (33)

By: Ge

Part Number: WE3X75

Bearing only, to get complete assembly order WE25M40

Do-It-Yourself Stories from Customers like You Was making a squeaking/squealing on start up Gerald G. • Nashua , NH • March 20, 2016

$18.69

Compare At:: $22.05
You Save:: $3.36

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Ge part

Idler Pulley (Dryer Belt Tensioner)

4.9 (19)

By: Ge

Part Number: WE12X81

This idler pulley keeps tension on the dryer drum belt so the motor can spin the drum smoothly. Replacing a worn pulley can quiet squealing and restore consistent tumbling.

Maintains proper belt tension so the drum turns under load
Free-spinning pulley reduces friction and belt wear
Common symptoms of failure: squealing/chirping noises, drum won't turn, belt slipping or fraying, burning rubber smell
Helps prevent the belt from jumping off the motor or drum

What's included: 1 idler pulley Install notes:

Disconnect power; for gas dryers, shut off the gas supply
Access typically requires removing the top/front panel and releasing belt tension to remove the drum
Transfer any spacers/retainer from the old pulley to the new one; the pulley spins freely before reassembly
Route the belt per the model's diagram and check belt alignment/tension before test run

Do-It-Yourself Stories from Customers like You The dryer was squeaking loudly George V. • Weirton , WV • December 13, 2014

I replaced the drum bearing in the back and also the nylon sliders in the front. It rook some time but was not difficult. I took some extra time to thoroughly clean all the lint from the inside. Read more

$13.76

Compare At:: $29.75
You Save:: $15.99

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Ge part

Screw

4.5 (6)

By: Ge

Part Number: WH2X930

Black. 8-18 AB HXW 3/8

Do-It-Yourself Stories from Customers like You Oven door trim rusted Gladys R. • Weston , FL • August 08, 2016

I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more

$11.74

Compare At:: $14.09
You Save:: $2.35

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Ge part

Felt Seal (Drum)

4.0 (1)

By: Ge

Part Number: WE9X38

This felt seal creates a smooth, airtight barrier where the drum meets the bulkhead in your dryer. Replacing a worn seal helps maintain proper airflow, protect fabrics from snagging, and reduce scraping or squealing noises during operation. What it does:

Seals the gap between the rotating drum and front/rear bulkhead to contain heat and airflow
Provides a low-friction, cushioned surface for the drum rim
Helps keep lint and debris out of the cabinet
Common symptoms of failure: longer or uneven dry times, rubbing/scraping noises, clothes catching or leaving marks at the drum edge, visibly worn or torn felt

What's included:

1 felt seal

Install notes:

Disconnect power; for gas dryers, also shut off the gas supply
Remove the top/front panel to access the drum and bulkhead; support drum as needed
Remove old felt and adhesive; clean the mating surface thoroughly
Dry-fit the new seal; install per manufacturer guidance; allow proper set time before reassembly
Hand-rotate the drum to verify even contact and clearance, then test operation

Do-It-Yourself Stories from Customers like You The felt seal was worn down resulting in metal on metal grinding from the drum against the inside of the front face Jonathan W. • Lamar , SC • October 27, 2014

I cut power to the dryer. I removed the face of the dryer. I then removed the felt mounts beneath the drum. I removed the old strips of felt and cut the new seal to fit both mounts. I then remounted the felt mounts and replaced the face. Read more

$48.57

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Ge part

Leveling Leg

5.0 (3)

By: Ge

Part Number: WE1M642

Adjustable

Do-It-Yourself Stories from Customers like You Missing parts. Les B. • Park City , UT • June 30, 2019

Installed the missing legs. Very east to do Read more

$14.37

Compare At:: $17.10
You Save:: $2.73

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Ge part

Screw

5.0 (1)

By: Ge

Part Number: WE2X263D

Package of 12

Do-It-Yourself Stories from Customers like You Squeaking very loud. Amy*armstrong A. • Kersey , PA • January 18, 2021

Watched the repair video. Saw what to look for. Found the dryer drum front support was broken and the slide bearings were worn. Replaced these items. Read more

$11.68

Compare At:: $14.02
You Save:: $2.34

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Ge part

Motor Strap (Dryer)

By: Ge

Part Number: WE13X200

This replacement motor strap secures the dryer's drive motor to its mounting bracket so the motor and blower stay aligned and stable, helping reduce vibration and noise for smoother operation. What it does:

Holds the drive motor firmly to the base/bracket
Maintains proper alignment of the motor and blower wheel to prevent rubbing
Helps reduce vibration, rattling, and related noise
Typical signs of failure: increased vibration, rattling, scraping from the blower area, or a motor that feels loose inside the cabinet

What's included:

Includes 1 motor strap

Install notes:

Disconnect power; for gas dryers, also shut off gas supply
Access the motor assembly; note the strap's routing/orientation before removal
Support the motor while releasing the strap to avoid stressing wiring and mounts
After securing the strap, rotate the drum/blower by hand to verify free movement before reassembly

$8.29

Compare At:: $9.08
You Save:: $0.79

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Ge part

Screw (12-Pack)

By: Ge

Part Number: WZ5X158D

Size: 8-32 t. Includes 12 screws.

$25.57

Compare At:: $30.43
You Save:: $4.86

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Ge part

Motor Pulley (Drive)

4.0 (1)

By: Ge

Part Number: WE12X41

This motor drive pulley guides the dryer drive belt and helps transfer motor power to the drum for proper rotation. Replacing a worn or damaged pulley restores smooth drum movement and reduces noise. What it does:

Guides and supports the drive belt so the drum turns evenly
Maintains belt alignment to prevent slipping or excessive wear
Reduces squealing or grinding caused by a damaged pulley bearing
Helps restore normal tumbling when the drum drags or hesitates

What's included:

One motor drive pulley

Install notes:

Disconnect power to the appliance before any service; follow lockout/tagout best practices
Inspect the drive belt and bearings while replacing the pulley; replace worn belt or bearings as needed
Typical service requires basic hand tools and access to the dryer cabinet or motor housing

Do-It-Yourself Stories from Customers like You Broken belt Richard B. • Fairfield , CT • March 14, 2015

Replaced belt, pulley with a 4 grove pulley. Pulley that was on there was a 3 grove pulley, Had to cut the old one off, Press on to shaft. Replaced rear drum bearing. Bearing was locked on with a snap ring. Access to it from a removable plate on the back side of dryer. Reset belt and idler puller by removing a long back plate on the bottom rear side of the dryer. None of this was shown in your Video. Read more

$27.25

Compare At:: $32.43
You Save:: $5.18

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Ge part

Wheel

By: Ge

Part Number: WE16X16

7" diameter

$63.25

Compare At:: $79.57
You Save:: $16.32

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Ge part

Ground Strap Assembly (Drum Shaft)

5.0 (1)

By: Ge

Part Number: WE1X1172

Do-It-Yourself Stories from Customers like You Was making a squeaking/squealing on start up Gerald G. • Nashua , NH • March 20, 2016

$27.28

Compare At:: $32.46
You Save:: $5.18

IN STOCK

Ships Monday Guaranteed

Add to Cart

Appliance

Appliance

Lawn & Garden

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Dde7500galwh Parts

Rear Drum Bearing Kit

Dryer Drive Belt

Door Latch

Clamp And Screw Kit

Dryer Motor Kit

Rear Drum Support Bearing

Idler Pulley (Dryer Belt Tensioner)

Screw

Felt Seal (Drum)

Leveling Leg

Screw

Motor Strap (Dryer)

Screw (12-Pack)

Motor Pulley (Drive)

Wheel

Ground Strap Assembly (Drum Shaft)