Eb294610 Parts

This Halogen Bulb is an OEM part for Bosch Ranges. It provides illumination for the range's interior. Continuous use or high temperatures can cause the bulb to burn out or fail.

What Causes a Bad Halogen Bulb: 
Repeated heating and cooling cycles, along with continuous use, can cause the halogen bulb to burn out or break.

Symptoms of a Bad Halogen Bulb:

• The bulb is not lighting up
• Visible signs of damage or a broken filament
• Flickering or intermittent lighting

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Fix an oven that won't heat to the right temperature or overheats food with this temperature sensor probe. Measures internal oven temp accurately.

Appliance overheating or shutting off unexpectedly? This high-limit thermostat cuts power when temperatures exceed safe levels, preventing damage.

Seals side lamp glass on lawn tractors, blocking moisture and debris from the housing. Replace when glass rattles or leaks occur. Confirm fit with your model.

This oven temperature probe is the internal sensor that monitors cooking cavity temperature so the oven control can regulate heat for accurate cooking and bake results. It's a direct-replacement sensing probe for compatible Bosch ovens. What it does:

• Measures internal oven temperature and sends readings to the control board
• Allows the oven to maintain set temperatures for consistent cooking
• Common symptoms of a failing probe: inaccurate oven temps, oven not reaching set temperature, or temperature-related error codes
• Works with the oven's control system to help cycle heating elements or gas valve

• Disconnect power to the appliance before servicing to avoid shock hazard
• Handle the probe and its wiring gently; avoid sharp bends or pulling on connectors
• Verify connector orientation and secure connections to the control board per OEM diagram

A female door latch that secures the appliance door and ensures a proper close for safe operation. Replaces a worn or broken latch to restore reliable door engagement and help the appliance start normally. What it does:

• Secures the door by engaging the corresponding door striker so the appliance can run
• Helps prevent the door from popping open during operation
• Commonly replaced when the door won't stay closed or the unit displays a "door"/won't-start symptom
• Fits the OEM latch location and mates with the matching male striker to restore proper function

• One female door latch

• Disconnect power (and gas, if applicable) before servicing
• Remove the outer door panel or access panel as required to reach the latch assembly
• Align the latch with the striker and secure fasteners; test door engagement before reassembly

This inner door seal replaces the worn gasket that keeps your appliance door watertight and helps maintain proper operation. Restores the door's seal to prevent leaks and reduce moisture and odor buildup inside the appliance. What it does:

• Creates a watertight seal along the inner door to help prevent leaks and water on the floor
• Helps maintain proper internal humidity and reduces odor and mildew risk
• Keeps the door aligned and cushioning contact between door panels
• Worn, torn, or deformed seals may lead to visible leaking or poor performance

• One inner door seal

• Disconnect power and water (if applicable) before replacing the seal
• Handle glass or door panels carefully to avoid breakage; wear gloves and eye protection
• Press the seal into the door channel evenly, checking for full seating around the perimeter

This control panel lens cover protects the oven's display and touchpad area from spills, scratches and everyday wear while keeping the display visible and looking finished. It restores the appliance's appearance and helps prevent damage to the underlying controls. What it does

• Shields the display and control buttons from food splatter, grease and scratches.
• Keeps the display readable by reducing direct contact and surface damage.
• Replaces cracked, chipped or yellowed lens surfaces that obscure the control panel.
• Helps prevent moisture from directly contacting the control electronics when properly seated.

• One lens cover for the control panel.

• Disconnect power to the appliance before starting any work.
• Typically installs by removing the control panel trim or bezel; handle the lens by the edges to avoid fingerprints.
• Inspect mounting tabs or clips for damage and align carefully before snapping or fastening into place.
• If screws or additional trim are required, reuse OEM fasteners.

Frame support bracket for front-tine tillers. Mounts to the main frame assembly to provide structural reinforcement. Replace if cracked, bent, or damaged.