Je2160co2 Parts

This high-voltage capacitor sits in the microwave's HV circuit, storing and releasing energy to power the magnetron. Replacing a weak or failed capacitor may restore heating performance and help reduce stress on other high-voltage components. What it does:

• Provides energy storage and filtering in the microwave's high-voltage circuit
• Works with the HV transformer and diode to supply power to the magnetron
• Common symptoms: runs but doesn't heat; loud hum/buzz during cook; blows the internal fuse or trips a breaker when cooking starts; visible bulging or leakage on the capacitor

• 1 high-voltage capacitor

• Unplug the microwave; for built-in/OTR units, switch off the circuit breaker as well
• The capacitor can retain a dangerous charge—use the proper discharge procedure
• Photograph wiring, transfer leads to the same terminals, and secure the capacitor in its bracket
• If no-heat persists, test the HV diode, transformer, and magnetron

This high-voltage diode assembly is part of the microwave's HV circuit. It converts the transformer's high-voltage AC to DC, enabling the magnetron to generate microwave energy so your unit can heat food properly.

• Rectifies high-voltage AC to DC in the microwave's high-voltage network
• Works with the HV transformer and capacitor to power the magnetron
• Failure may cause "runs but doesn't heat"
• Other possible signs include a loud hum during cook or a blown internal fuse at start-up

• Unplug the microwave; the HV capacitor can hold a dangerous charge—discharge it properly before servicing
• Observe diode polarity/orientation and install in the same direction as the original
• Ensure secure, insulated connections and proper routing away from sharp edges

This replacement hook fastens a mating part to your appliance, keeping the assembly properly retained and aligned. Replacing a worn or missing hook restores a snug fit, reduces rattles, and ensures components stay securely in place.

• Provides the retention point for a panel, grille, or assembly
• Maintains proper alignment and support during operation
• Helps prevent looseness, vibration, or rattling
• Symptoms include: part won't stay seated, difficulty latching, or a loose fit

• Disconnect power to the appliance before servicing
• Access the mounting area and note the hook's orientation and location
• Transfer and reuse any original screws/clips or hardware as required
• After installation, ensure the mating part engages fully and operates normally

This replacement foot fits select GE microwaves. It provides a stable, cushioned contact point so the unit or its removable rack sits level, stays steady during operation, and helps protect surfaces from wear.

• Supports and cushions the microwave cabinet or a removable rack/accessory
• Helps keep the unit level to reduce wobble and vibration
• Protects interior and countertop surfaces from scuffs and marks
• Replaces missing, cracked, or flattened feet that cause rocking or rattling

• Disconnect power and allow the appliance to cool before servicing
• Remove the worn or missing foot and clean the mounting area
• Press or slide the new foot fully into place until secure
• The unit or rack sits level and stable before use

This replacement spring hook secures a door/spring assembly to restore proper tension and alignment so the door closes and operates as intended. Fits the OEM spring mounting location and installs in minutes with basic hand tools. What it does:

• Latches and anchors a door or tension spring to maintain spring tension and proper door movement
• Helps stop door from sagging, not fully closing, or coming loose when the hook has worn or detached
• Durable stamped metal construction for reliable holding strength under normal use
• Works as the direct replacement piece for the corresponding OEM spring attachment point

• One spring hook replacement part

• Disconnect power (and gas or fuel if applicable) before starting repairs
• Relieve spring tension carefully; springs can be under high load—wear eye protection and gloves
• Use common hand tools (screwdriver, pliers) to remove and attach the hook; retain any clips or fasteners

The Interlock Switch is an OEM replacement part for GE microwaves. It acts as a safety device that prevents the microwave from operating unless the door is securely closed and latched. The switch monitors the door position and communicates with the main control board to allow or cancel cooking functions.

Causes of failure may include damage from excess heat over time or wear from repeated door openings and closings. Failures can compromise safety if the microwave operates unexpectedly while open.

Symptoms of a bad interlock switch include:

• Microwave can be turned on even when the door is open     
• Error codes displayed related to door issues  
• Inconsistent or faulty communication with the control board

This genuine OEM replacement part is also compatible with GE, Hotpoint, and select Kenmore microwave models.

This latch slider is the replacement sliding component used in the door latch assembly to help secure the appliance door and enable proper latching. Replaces a worn or broken slider to restore reliable door engagement. What it does

• Slides along the latch assembly to engage or release the door catch for secure closing
• Helps the door fully latch so the appliance can start and run normally
• Common symptom: door won't latch or stays ajar even when closed
• Common symptom: door latch feels loose, sticks, or makes noise when operated

• One latch slider

• Disconnect power (and water if applicable) before starting any repairs
• Removing the door or front panel may be required to access the latch assembly
• Use basic hand tools; handle trim and glass carefully to avoid damage
• Verify proper alignment of the slider and latch after installation before restoring power

The Door Gasket is an OEM part for GE built-in microwaves. Installed around the inner edge of the microwave door, this rubber seal forms an important barrier and insulation component. 

Symptoms of a defective door gasket include: 

• Microwave leaking heat or emitting sounds/vibrations during operation
• Visible wear, cracks or shrinkage around the door sealing area  
• Difficulty closing or locking the door securely
• Steam or condensation developing inside the cavity or door glass  

Factors like age, heat deterioration or damage over time can compromise the pliable material. 

This genuine OEM GE replacement is compatible with additional Hotpoint, RCA and Kenmore models.

This power cord assembly restores the main electrical connection to your appliance, providing a safe, routed supply line for consistent operation. Use it to replace a damaged, frayed, or non-functioning power cord and regain reliable power. What it does

• Replaces the appliance's main power cord to restore full electrical connection
• Fixes symptoms such as intermittent power, no power at the appliance, visible cord damage, or scorch marks at the cord connection
• Provides a factory-style replacement that routes and secures the cord where the OEM design intends
• Prevents unsafe operation caused by exposed or degraded wiring

• One factory-style power cord assembly

• Disconnect power at the breaker or unplug the appliance before beginning any work
• Route the cord through the strain relief and secure all terminal connections tightly
• If you see melting, corrosion, or damaged terminals, replace the mating parts.