Je2160sf01 Parts

This high-voltage diode assembly is part of the microwave's HV circuit. It converts the transformer's high-voltage AC to DC, enabling the magnetron to generate microwave energy so your unit can heat food properly.

• Rectifies high-voltage AC to DC in the microwave's high-voltage network
• Works with the HV transformer and capacitor to power the magnetron
• Failure may cause "runs but doesn't heat"
• Other possible signs include a loud hum during cook or a blown internal fuse at start-up

• Unplug the microwave; the HV capacitor can hold a dangerous charge—discharge it properly before servicing
• Observe diode polarity/orientation and install in the same direction as the original
• Ensure secure, insulated connections and proper routing away from sharp edges

This replacement hook fastens a mating part to your appliance, keeping the assembly properly retained and aligned. Replacing a worn or missing hook restores a snug fit, reduces rattles, and ensures components stay securely in place.

• Provides the retention point for a panel, grille, or assembly
• Maintains proper alignment and support during operation
• Helps prevent looseness, vibration, or rattling
• Symptoms include: part won't stay seated, difficulty latching, or a loose fit

• Disconnect power to the appliance before servicing
• Access the mounting area and note the hook's orientation and location
• Transfer and reuse any original screws/clips or hardware as required
• After installation, ensure the mating part engages fully and operates normally

This thermostat cavity is a genuine General Electric part, sold individually. It can be used as a replacement part for a microwave. This thermostat cavity regulates the temperature and power of the appliance so that it can properly heat up food and other items inserted into the appliance. The thermostat cavity is made out of durable gray metal.The thermostat cavity of a microwave might have to be replaced if it exhibits either of the following symptoms: the exhaust fan of the microwave is malfunctioning, or the microwave does not run or runs for under ten seconds before stopping. If either of these symptoms occur, the thermostat cavity should be removed and replaced by this genuine OEM replacement part before using the microwave again. Remember to wear work gloves while inspecting the thermostat cavity and while conducting a replacement. It is a relatively complicated replacement that will require several special tools.This is an OEM part sourced directly from the manufacturer. It is sold individually. This thermostat cavity is compatible with General Electric brand microwaves.

This replacement foot fits select GE microwaves. It provides a stable, cushioned contact point so the unit or its removable rack sits level, stays steady during operation, and helps protect surfaces from wear.

• Supports and cushions the microwave cabinet or a removable rack/accessory
• Helps keep the unit level to reduce wobble and vibration
• Protects interior and countertop surfaces from scuffs and marks
• Replaces missing, cracked, or flattened feet that cause rocking or rattling

• Disconnect power and allow the appliance to cool before servicing
• Remove the worn or missing foot and clean the mounting area
• Press or slide the new foot fully into place until secure
• The unit or rack sits level and stable before use

This barrier screen is the molded door air baffle that helps direct and control refrigerator airflow to maintain proper cooling and protect interior components. It restores intended air circulation for more even temperatures. What it does:

• Directs cold air through the door to balance temperatures across compartments
• Prevents unwanted drafts and helps reduce hot/cold spots inside the refrigerator
• Helps keep vents and internal components protected from debris
• Reduces frost buildup caused by disrupted airflow

• Disconnect power before starting any repair to avoid electrical shock
• Remove the door bin or liner as needed to access the mounting clips
• Align the tabs and press until clips engage; do not force or pry on brittle tabs
• If mounting hardware is damaged, replace clips to ensure a secure fit

This replacement spring hook secures a door/spring assembly to restore proper tension and alignment so the door closes and operates as intended. Fits the OEM spring mounting location and installs in minutes with basic hand tools. What it does:

• Latches and anchors a door or tension spring to maintain spring tension and proper door movement
• Helps stop door from sagging, not fully closing, or coming loose when the hook has worn or detached
• Durable stamped metal construction for reliable holding strength under normal use
• Works as the direct replacement piece for the corresponding OEM spring attachment point

• One spring hook replacement part

• Disconnect power (and gas or fuel if applicable) before starting repairs
• Relieve spring tension carefully; springs can be under high load—wear eye protection and gloves
• Use common hand tools (screwdriver, pliers) to remove and attach the hook; retain any clips or fasteners

The Interlock Switch is an OEM replacement part for GE microwaves. It acts as a safety device that prevents the microwave from operating unless the door is securely closed and latched. The switch monitors the door position and communicates with the main control board to allow or cancel cooking functions.

Causes of failure may include damage from excess heat over time or wear from repeated door openings and closings. Failures can compromise safety if the microwave operates unexpectedly while open.

Symptoms of a bad interlock switch include:

• Microwave can be turned on even when the door is open     
• Error codes displayed related to door issues  
• Inconsistent or faulty communication with the control board

This genuine OEM replacement part is also compatible with GE, Hotpoint, and select Kenmore microwave models.

This high-voltage capacitor sits in the microwave's HV circuit, storing and releasing energy to power the magnetron. Replacing a weak or failed capacitor may restore heating performance and help reduce stress on other high-voltage components. What it does:

• Provides energy storage and filtering in the microwave's high-voltage circuit
• Works with the HV transformer and diode to supply power to the magnetron
• Common symptoms: runs but doesn't heat; loud hum/buzz during cook; blows the internal fuse or trips a breaker when cooking starts; visible bulging or leakage on the capacitor

• 1 high-voltage capacitor

• Unplug the microwave; for built-in/OTR units, switch off the circuit breaker as well
• The capacitor can retain a dangerous charge—use the proper discharge procedure
• Photograph wiring, transfer leads to the same terminals, and secure the capacitor in its bracket
• If no-heat persists, test the HV diode, transformer, and magnetron

This latch slider is the replacement sliding component used in the door latch assembly to help secure the appliance door and enable proper latching. Replaces a worn or broken slider to restore reliable door engagement. What it does

• Slides along the latch assembly to engage or release the door catch for secure closing
• Helps the door fully latch so the appliance can start and run normally
• Common symptom: door won't latch or stays ajar even when closed
• Common symptom: door latch feels loose, sticks, or makes noise when operated

• One latch slider

• Disconnect power (and water if applicable) before starting any repairs
• Removing the door or front panel may be required to access the latch assembly
• Use basic hand tools; handle trim and glass carefully to avoid damage
• Verify proper alignment of the slider and latch after installation before restoring power

The Door Gasket is an OEM part for GE built-in microwaves. Installed around the inner edge of the microwave door, this rubber seal forms an important barrier and insulation component. 

Symptoms of a defective door gasket include: 

• Microwave leaking heat or emitting sounds/vibrations during operation
• Visible wear, cracks or shrinkage around the door sealing area  
• Difficulty closing or locking the door securely
• Steam or condensation developing inside the cavity or door glass  

Factors like age, heat deterioration or damage over time can compromise the pliable material. 

This genuine OEM GE replacement is compatible with additional Hotpoint, RCA and Kenmore models.

This decorator button assembly replaces a damaged or missing control-panel button to restore push-button function and appearance. It snaps into the console and provides a reliable surface for operating the appliance's control switches. What it does

• Replaces a worn, cracked, or missing decorator button so presses register cleanly
• Restores the original look of the control panel for consistent user operation
• Aligns with the control switch beneath and transmits button presses to the switch
• Helps eliminate sticking, intermittent activation, or cosmetic damage from everyday use

• Disconnect power to the appliance before beginning any work to avoid shock or injury.
• Remove any trim or console pieces as needed to access the button; basic hand tools may be required.
• Snap the button assembly into the panel and verify it properly engages the switch and moves freely.