Line Mover Badge Chute Parts

Prevents water from leaking at door corners in your dishwasher. Replace if you notice pooling water on the floor during cycles. Easy DIY install.

Reduce noise and prevent heat loss with this dishwasher toe panel insulation. Replace when soiled, damaged, or missing. Adhesive-backed for easy install.

Replacement hinge brace for dishwasher doors. Anchors the door hinge assembly to the tub. Install if original is cracked, warped, or missing.

Replaces cracked, peeling, or worn control panel faceplate on your oven. Covers and protects control assembly while restoring a finished appearance.

This diverter valve directs wash water inside the machine, switching flow between internal paths during wash and drain/recirculation steps. Replacing a failed diverter restores proper water routing so cycles advance and complete as designed.

• Redirects water between the drain and recirculation/spray paths as commanded by the control
• Ensures correct water flow for wash, rinse, and drain steps
• A sticking or failed diverter can cause slow/no drain or no recirculation/spray
• May lead to cycle pauses/errors, unusual clicking/buzzing from the valve area, or leaks at the valve body/ports

• Unplug the washer and turn off water supply; expect residual water in hoses
• Access location varies by model; typically mounted along the pump/hoses under the cabinet
• Move hoses/clamps and the electrical connector one at a time; match port orientation
• After installation, run a rinse/drain test and check all connections for leaks

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Decorative nameplate badge for oven and range front panels. Replaces missing, worn, or damaged emblems to restore factory appearance. Includes adhesive.

Guides dryer airflow from drum to lint screen housing. Replace if cracked, broken, or missing to restore proper air path and contain lint in ductwork.

Replacement nameplate that restores your refrigerator's factory identification label. Adhesive-backed plate needed when original is faded, damaged, or missing.

This is a black surface burner cap that sits on top of the burner base to distribute the flame evenly across the cookware. It covers the center of the burner assembly and helps produce a uniform ring of flame. Replace this cap if it is cracked, chipped, warped, or if you notice uneven flame patterns during cooking.

Replacement nameplate label for refrigerators. Restores model, serial, and electrical rating information when original is faded, peeling, or missing.

Barrier guard for dishwasher inner door panel. Separates and protects components, keeping wiring properly aligned. Replace if cracked, broken, or missing.

This center trim is the molded bezel that fits the front center of the cooktop/oven control area, restoring a finished look and protecting the control panel edges from heat and grime. What it does:

• Covers and protects the exposed edge of the control panel for a clean appearance
• Hides gaps, chips or discolored trim that make the console look worn
• Helps prevent dirt and grease from getting behind the control assembly
• Restores proper alignment and fit where the original trim is cracked or broken

• Disconnect power to the appliance before starting any repair.
• Typically secures with clips or screws—retain hardware and note orientation when removing old trim.
• Handle edges carefully; replacement may require gentle prying with a trim tool.
• If mounting hardware or support brackets are damaged, replace them separately.

Water deflector for dishwashers. Directs spray during wash cycles. Replace if cracked, broken, or missing to restore proper water distribution.

Left switch breakwater bracket secures console switch assembly in dishwasher door. Replace if cracked, broken, or missing to restore proper alignment.

Dishwasher door guard installs on the door hinge for reinforcement and support. Replace if cracked, broken, or missing to prevent door bending.