Med Propeller Rear Badge Mover Parts

This faceplate is the front cover for the control panel. It restores a finished look and helps protect and support the control assembly so the controls align and operate correctly.

• Covers and shields the control assembly from everyday use
• Provides secure mounting and proper alignment for controls
• Replace if cracked, warped, or if mounting tabs are broken
• Common signs include a loose or missing cover, rattling panel, or misaligned controls

• Disconnect power at the breaker before servicing
• Remove screws/retainers to lift the control panel; support the board and wiring
• Transfer any existing brackets or clips to the new faceplate as needed
• Reinstall, restore power, and test

This replacement propeller is used on the outdoor fan of room air conditioners. It mounts to the condenser fan motor shaft to move air across the condenser coil, restoring heat rejection and airflow when the original blade is damaged or unbalanced. What it does:

• Moves outdoor air through the condenser coil to expel heat
• Helps address poor cooling caused by weak or no condenser airflow
• Replaces cracked, warped, or loose blades that cause vibration or scraping noises
• Symptom check: outdoor fan not spinning, weak airflow, rattling, or visible blade damage

• Includes: 1 propeller

• Disconnect power before servicing; wear gloves—blade edges can be sharp
• Note blade orientation and hub depth on the motor shaft before removal
• Remove the fastener/set screw and pull the old blade straight off; avoid bending coil fins
• Install the new blade in the same orientation, secure firmly, then test run

This logo badge is the decorative nameplate used on select cooking appliances. Replacing a missing or worn emblem restores the finished factory look and keeps the front of your appliance looking complete and consistent with the original design.

• Cosmetic component that displays the appliance logo and completes the front panel or door
• Replaces a badge that is missing, cracked, peeling, or discolored
• Helps refresh the appliance's appearance without affecting operation
• Common signs: badge fell off, won't adhere, looks faded or damaged

• Disconnect power before working near control panels or doors
• Note the badge's original location and orientation before removal
• Use a non-marring tool to gently lift the old emblem if present; avoid scratching finishes
• Clean and dry the surface thoroughly before pressing the new badge into place

A replacement name plate that restores the appliance's factory identification label so model and serial information are legible for service and parts lookup. Helps maintain the appliance's appearance and accurate identification. What it does:

• Provides the factory identification area showing model/serial and manufacturer data for parts lookup and service.
• Use when the original label is missing, scratched, faded, or peeling and no longer readable.
• Restores exterior appearance where the original name plate has cosmetic damage.

• Clean and dry the mounting surface before installing; remove old adhesive residue if present.
• Align carefully and press firmly; some installations may require removal of trim or a cover.
• Use appropriate tools and avoid sharp solvents that could damage surrounding surfaces.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This axial flow fan moves air through the appliance to help cool internal components and support proper airflow. Replacing a worn or damaged fan restores quiet operation and helps prevent overheating-related issues. What it does:

• Circulates air across internal components or heat exchangers to maintain proper operating temperatures
• Helps prevent overheating of electronics, motors, or heating elements
• Reduces abnormal noise caused by worn or imbalanced fan blades or bearings
• Supports consistent airflow for reliable appliance performance

• One axial flow fan assembly

• Disconnect power to the appliance before starting any repair
• Handle the fan blades carefully to avoid damage; align properly during installation
• Verify secure mounting and electrical connections before restoring power
• Test appliance operation after installation and observe for proper airflow and quiet operation

This center trim is the molded bezel that fits the front center of the cooktop/oven control area, restoring a finished look and protecting the control panel edges from heat and grime. What it does:

• Covers and protects the exposed edge of the control panel for a clean appearance
• Hides gaps, chips or discolored trim that make the console look worn
• Helps prevent dirt and grease from getting behind the control assembly
• Restores proper alignment and fit where the original trim is cracked or broken

• Disconnect power to the appliance before starting any repair.
• Typically secures with clips or screws—retain hardware and note orientation when removing old trim.
• Handle edges carefully; replacement may require gentle prying with a trim tool.
• If mounting hardware or support brackets are damaged, replace them separately.

A decorative medallion trim piece that restores the finished look of your appliance front. Replaces a scratched, faded or missing medallion to improve appearance and maintain original styling. What it does:

• Covers and protects the underlying surface while matching the appliance's original finish
• Restores a clean, finished look when the factory medallion is damaged or discolored
• Helps keep grime and moisture out of seams around the emblem area
• Useful when replacing a damaged control/door trim for a consistent appearance

• One medallion decorative trim

• Surface-mount replacement; peel adhesive or fasten per original attachment method
• Clean and dry mounting area before installing for best adhesion
• Handle carefully to avoid scratching the finish during installation

This replacement nameplate label restores the appliance's identification and rating information so you can read model, serial, and electrical data clearly. Helps when the original label is faded, damaged, or missing. What it does

• Displays model and serial numbers, electrical ratings and safety markings for identification and service
• Replaces faded, torn, or illegible factory labels so appliance data is readable
• Helps technicians and owners confirm correct specifications during repairs or replacement parts ordering
• Does not affect appliance operation; used for identification and information only

• One replacement nameplate label

• Clean and dry the surface before applying so the label adheres and lays flat
• Align carefully; many labels are adhesive-backed and are intended for single use
• Avoid placing over gaskets, vents, or moving parts; install where original label was located

This evaporator blower fan blade circulates cold air through the refrigerator to maintain even cooling and proper frost control. Replacing a worn or broken blade restores airflow and helps the appliance cool more consistently. What it does:

• Spins on the evaporator motor to move air across the evaporator coils
• Promotes even temperature distribution inside the fresh-food and freezer compartments
• Helps prevent frost build-up by maintaining steady airflow
• Commonly replaced when airflow is weak, the fan is noisy, or the blade is cracked or broken

• One fan blade

• Disconnect power before accessing the evaporator/fan area to avoid shock or injury
• Handle the blade carefully to avoid bending fins or damaging the motor shaft
• The motor shaft and mounting hardware are intact before installation

Color: Stainless

The Fan Blade is an OEM replacement part for Frigidaire window air conditioners. Located inside the unit behind the protective grill, the fan blade rotates to circulate cooled air throughout the room. Made with corrosion-resistant materials, the precisely balanced blade withstands constant rotation during seasonal operation.  

Symptoms of a bad fan blade include:

• Excessive vibrations or strange noises from the AC unit  
• Reduced air circulation felt in the room
• The blade visibly rubbing or hitting the fan enclosure

Causes can be dirt buildup causing imbalance, broken blade tips from impacts, or loosened set screws allowing shaft wobbling over extended use. 

Replacing this OEM Frigidaire part restores smooth, powerful air distribution. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement blade fan moves cold air across the evaporator to help maintain even temperatures inside the compartment. It restores proper airflow for more consistent cooling and helps reduce frost buildup when working with a good motor. What it does:

• Circulates air across the evaporator to distribute cold air through the compartment
• Restores airflow when a cracked, warped, or missing blade reduces cooling efficiency
• Helps reduce uneven temperatures and localized warm spots caused by poor airflow
• Can reduce abnormal noises caused by damaged or unbalanced blades

• One replacement blade fan

• Disconnect power to the appliance before starting any repair
• Remove the evaporator cover/panel to access the fan assembly per your model's service instructions
• Handle the replacement blade carefully to avoid bending the blades or contaminating the evaporator
• If the fan motor or mounting hardware is damaged, replace those parts as well for reliable operation

This axial flow fan circulates air inside the appliance to help cool components and maintain proper ventilation. It replaces a worn or damaged blower wheel to restore airflow and reduce overheating risk. What it does:

• Moves air across coils or internal components to support cooling and ventilation.
• Helps prevent overheating and supports consistent appliance performance.
• Can reduce unusual temperature-related symptoms or poor cooling/airflow.
• Fits into the appliance's blower/motor assembly to restore proper airflow.

• Disconnect power to the appliance before starting any repair.
• Handle the fan blades carefully to avoid bending or damage.
• Verify proper seating on the motor shaft and secure fasteners per the appliance's service instructions.