2006Yahoocom Parts

This electric heater restores the heat your machine needs to reach and maintain proper operating temperature. Replacing an open or weak element brings back consistent heating so cycles complete as intended. What it does:

• Converts electrical power into heat within the appliance's heating circuit
• Works with thermostats and controls to maintain target temperature
• Common symptoms: no heat or lower-than-expected temperatures
• Extended cycle times or inability to reach set temperatures

• 1 heater element

• Disconnect power at the breaker and allow the unit to cool completely before service
• Note wire positions; move connectors one at a time and avoid stressing the coil/insulators
• Inspect related thermostats, cutoffs, wiring, and airflow/circulation issues to prevent repeat failures
• The part matches your model's required voltage rating (208V) before restoring power

This round cooktop surface element provides a direct heat source for electric ranges, restoring one burner's ability to heat cookware evenly. It's a straightforward replacement for a damaged or non-heating burner element. What it does:

• Heats cookware on an electric range cooktop so pots and pans can reach cooking temperatures
• Replaces a cracked, burned-through, or non-functioning surface element to restore burner operation
• Helps eliminate intermittent or no-heat symptoms on the affected burner
• Works with the range's existing terminal block and controls when compatible

• One cooktop surface (round) element

• Disconnect power to the range at the circuit breaker before starting work
• Remove the damaged element from its terminal connections and lift out; install the new element by seating terminals fully and testing power
• Use care to avoid scratching the cooktop surface and verify element compatibility with your model

This part is a replacement hex bolt. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a lost or defective hex bolt in outdoor power equipment. The hex bolt is named for its hexagonal shaped head and is important for properly securing together different equipment components. It should be replaced if lost, worn, stripped, corroded, or ineffective in any way. When working on or near an enginee, it is important to ensure the equipment is powered down and completely cool before beginning repairs. For more accurate information on how and where to place this hex bolt, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this hex bolt is suitable for use on outdoor power equipment manufactured by MTD, Craftsman, Troy-Bilt and other brands. Please note that this is a genuine part made of high-quality, durable metal and is sold individually.

This is a seven-inch cable tie that is used with different types of lawn and garden equipment. It is most commonly used to secure the cable onto the handle of the lawnmower or tiller so it is secure. The cable tie is made of durable plastic but can be damaged or break. When this happens, the tie will need to be replaced to ensure the cable stays on the handle.If the cable tie needs to be replaced, no tools are needed. In the situation where other parts need to be replaced at the same time, a basic set of tools and a pair of work gloves may be required. Turn off the yard equipment and place it on a stable surface before replacing the broken cable tie. The old tie can be removed so the new one can be installed before further use.This cable tie is an authentic OEM replacement part that is directly sourced from the manufacturer. This product is sold individually. The component is designed to be compatible with lawnmowers, lawn tractors, tillers, and snowblowers manufactured by MTD, Troy-Bilt, Yard-Man, and Yard Machines.

This is a replacement bell washer, a flat washer that can be used with a wide range of various types of lawn and garden equipment. The inner dimension of this washer is 0.40 inches, while the outer dimension is 0.88 inches. Washers are typically used as a way to help ensure a tight connection when used with bolts or screws. They will also help to distribute the pressure of the connection and reduce the risk of corrosion. Washers will also provide some protection from damage during installation. Washers could need to be replaced for any number of reasons. In some cases, they might have become corroded or worn down over time. This could mean they no longer provide a solid and secure connection. Other times, the washer could become lost while working on the machine. Owners should always be sure that they replace any lost or damaged washers right away. Not using washers can reduce the lifespan of the machine. This is a genuine OEM bell washer that is sold individually. It is typically used in lawn mowers, snowblowers, tillers, leaf blowers, string trimmers, log splitters, wood chippers, edgers, and chainsaws. It is compatible with Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, and MasterCut brands.

This replacement part is a shoulder screw. This part is small but very important in various types of appliances. Shoulder screws are able to work with other small parts such as nuts or washers to ensure that pieces in the machine are held together securely during use.Overtightened screws might be stripped and could fall out or get stuck in place, necessitating replacement. Over time, exposure to the elements may lead to a screw becoming worn or corroded, which may cause it to break or get stuck.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

This bell washer is a genuine MTD part, sold individually. This bell washer can be used as a replacement part for a lawn tractor, chipper shredder, tiller, or lawnmower. This bell washer adds spacing on a shaft in the tool.If the user of the appliance notices that a washer is missing, it should be replaced. General wear and tear is very normal for outdoor appliances, and if it occurs, the washer should be removed and replaced with this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bell washer is compatible with the following outdoor appliance brands: MTD, Yard Man, Yard Machines, and Troy-Bilt.

This replacement part is a blade. This is a genuine replacement part made by MTD. Blades are commonly found in lawn mowers and assist in cutting or trimming grass according to the user's preferences. A new blade might be needed if the current one is damaged in any way. This can include being dented or bent. Additionally, if the blade is too dull and can no longer cut grass effectively, it should be replaced as soon as possible to return the machine to working condition. Be sure to wear work gloves as the new blade will be extremely sharp and can cause injury. It is recommended that the engine be turned off before attempting to replace this part.This part is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This replacement part is a hex screw. This is a genuine replacement part made by MTD. This type of screw is commonly found in many types of machinery and appliances. Screws are able to keep certain parts stable and connected so that they are secure during use. A new hex screw might be needed if the current one is visibly damaged in any way or missing. It is not uncommon for screws to become stripped down or lodged in place after years of normal use. If this is the case they should be replaced as soon as possible. If the screw is lodged in place, pliers might be required on top of a screwdriver to complete this repair. This part is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This screw is a genuine MTD part. A screw can be used as a replacement part in lawn mowers, snowblowers, tillers, chainsaws, log splitters, and wood chippers. The purpose of this genuine OEM part is to rotate and pierce into one or more components within the internal or external machinery of the appliance so that the stability of those components is maintained throughout general use of the appliance.The screw in an lawn equipment might need to be replaced if it has been lost, misplaced, or has suffered enough damage as to loosen the components that it is supposed to secure.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This screw is compatible with equipment manufactured by MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Murray, Yard Machines, Huskee, Montgomery Wards, Yard Man, Turf King, and MasterCut.

This replacement part is an adjuster kit. It is a genuine replacement part made by MTD. This adjuster kit is typically found in lawnmowers and is responsible for assisting the user in changing the height of the blades so that the user may determine the setting which the grass is cut at. A new adjuster kit might be needed if the user is unable to adjust the height of the blades and therefore cannot perform the necessary duties. If the blades are stuck at one height it is possible that the adjuster kit is to blame. Because this part is located close to dangerous objects it is recommended that work gloves be worn for protection. This is a genuine OEM replacement part to ensure proper fit and long-lasting use. Note that part is sold individually and is sourced directly from the manufacturer.

This spacer is a genuine MTD part. A spacer can be used as a replacement part in a lawn mower or a log splitter. The purpose of this genuine OEM part is to reduce friction between one or more components while also keeping the components apart from one another.The spacer is a small fastening component that can be easily lost or misplaced without notice for a variety of reasons. If the spacer is damaged, it should be immediately removed and replaced.This is a genuine OEM replacement sourced directly from the manufacturer. It is sold individually. This spacer is compatible with equipment manufactured by MTD, Craftsman, Troy-Bilt, Yard Machines, Yard Man, Turf King, and MasterCut.