Speed Queen Washer Parts

This black door boot seal forms a watertight barrier between the door and front tub on a front-load washer, keeping wash water contained. Replace a worn or torn seal to stop leaks and restore reliable operation. What it does

• Seals the gap between the door and front tub to prevent water leaks
• Helps direct water back into the drum during operation
• Maintains proper containment when filling, washing, and spinning
• Common failure signs: water leaking from the door/front, visible tears or cracks, or the gasket pulling loose

• Includes: 1 black door boot seal

• Disconnect power and turn off water supply before servicing
• Open the door and carefully release the inner and outer retaining clamps/springs
• Note the seal's orientation (alignment marks/drain ports) and install the new seal the same way
• Ensure both inner and outer lips are fully seated; reinstall clamps and run a short test cycle to check for leaks

This fabric softener dispenser assembly holds liquid softener and releases it during the rinse cycle. Replacing a cracked, missing, or clogged dispenser restores reliable dispensing, reduces messes, and helps keep the washer tub and laundry free of residue. What it does:

• Holds fabric softener and meters its release during the rinse phase
• Uses a simple siphon action to deliver softener evenly into the tub
• Helps prevent spills, streaks, and build-up from manual pouring
• Common symptoms: softener left in cup after cycle, leaks or drips, cracked/loose cup or cap, residue/odor in dispenser area

• 1 fabric softener dispenser assembly

• Disconnect power to the washer before servicing
• Remove the old dispenser from its mounting point; some models require a twist or releasing locking tabs
• Clean any residue from the mounting area to ensure proper flow
• Align and press the new dispenser firmly until fully seated, then test with a small amount of water

This replacement switch assembly restores the appliance's electrical switching function so the control or safety circuit can open and close when activated. Use it to replace a worn or failed switch and regain expected control response. What it does:

• Acts as the electrical contact that opens or closes a circuit when toggled or pressed
• Commonly used where a user action or door/lid position must be sensed by the control
• Can address symptoms such as no start, unresponsive controls, or intermittent operation tied to the switch circuit
• Transfers the mechanical action to the appliance's control or safety system

What's included: One switch assembly Install notes:

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Verify correct wiring and connector orientation before reassembly; take photos if needed
• Test switch continuity (with power off) after installation to confirm correct operation

This replacement control assembly manages cycle selection and timing for select 4-cycle washers with a Heavy Soil option. Restores reliable starting, correct cycle advancement, and consistent operation when the original control fails.

• Sequences fill, wash/agitation, drain, and spin based on the chosen cycle
• Provides user control for 4 wash cycles and a Heavy Soil option
• Regulates power to components such as the motor, water valves, and pump
• Helps address symptoms like won't start, won't advance or stops mid-cycle, some cycles inoperative, or erratic timing

• Disconnect power before servicing; use proper ESD precautions when handling electronics
• Access the console/control compartment and document wire locations (photos help)
• Transfer connectors one at a time to the new assembly and mount securely
• Reassemble, restore power, and run a test cycle to proper operation

The Drain Pump is an OEM component for Speed Queen washing machines. It is an important electric part that works to remove water from the washer tub at the end of each cycle. 

Symptoms of a failing drain pump include:

• The washer not fully draining water after cycles
• Excessively long drain times
• Unusual noises coming from the pump area

Causes stem from blockages in the pump chamber or drain hose, worn impeller assembly, or damaged electrical components inhibiting proper operation.

This Speed Queen replacement pump restores the machine's essential draining ability for hygienic washing. It ensures the removal of all water to prevent residual moisture issues. 

This timer knob assembly is the replacement control knob that lets you set and adjust cycle time on the dryer/washing machine control. It restores a secure grip and clear cycle selection so you can operate the machine easily. What it does:

• Provides a firm, easy-to-turn control for selecting timer settings and cycles
• Replaces cracked, stripped, or missing knobs that are hard to turn or won't stay set
• Helps ensure the timer/control shaft is engaged for accurate cycle selection
• Matches OEM fit and function for a direct replacement when the knob is worn or damaged

• Disconnect power to the appliance before attempting replacement
• Knob typically pulls straight off the control shaft; align splines and press on until seated
• If a retaining clip or screw is present, remove and reinstall as needed—retain hardware
• Do not force the knob; confirm proper alignment to avoid damaging the control shaft

This white temperature knob replaces a worn or broken control knob to restore reliable temperature selection on your range or oven. Simple cosmetic replacement that gives you a solid grip and clear control. What it does:

• Fits onto the temperature control shaft so you can set and adjust oven/range temperature
• Restores a secure, non-slip grip when original knob is cracked, loose, or missing
• Helps ensure accurate manual selection of heat settings by providing clear pointer alignment
• Commonly used when knobs won't turn, won't stay in position, or are cosmetically damaged

• Disconnect power to the appliance before beginning any service
• Align the knob's internal spline with the control shaft and push straight on until seated; do not force
• If knob does not fit, confirm correct part number and shaft type before proceeding

This replacement knob assembly with skirt restores a secure, easy-to-turn control interface on the appliance. It provides a finished look while allowing reliable selection of settings. What it does:

• Replaces a cracked, stripped, or missing control knob to restore user control
• Provides a stable grip and tactile feedback when turning settings
• Helps prevent accidental slips or selector misalignment caused by worn knobs
• Matches the original mounting style for a direct-fit replacement

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the old knob by pulling straight off the control shaft; install the new knob by aligning and pushing fully onto the shaft
• If the original used a retaining clip or set screw, verify and reinstall it; only use parts explicitly included

This Drive belt keeps the washer's transmission and tub turning by transferring motor power to the drum. Replaces a worn or broken belt to restore normal agitation and spinning performance. What it does:

• Transfers motor torque to the transmission/drum so the washer agitates and spins
• Stops slippage that can cause slow or no spin/agitate cycles
• Helps eliminate squealing or burning-rubber noises when the belt is worn
• Prevents further motor/drive damage from a broken or glazed belt

• Disconnect power and water supply before starting any repairs
• Remove access panels and shift the drum to relieve belt tension for removal
• Inspect pulleys, idler, and motor shaft for wear or debris before installing the new belt
• Route the belt according to the OEM diagram, then test run the machine

This 2 oz tube of silicone grease lubricates seals, gaskets and moving plastic or rubber parts to reduce noise and wear. It resists water and helps maintain smooth operation of appliance components. What it does:

• Lubricates rubber seals, gaskets, O-rings and sliding plastic parts to reduce sticking and squeaks
• Helps protect parts from moisture and prevents drying or cracking of elastomers
• Safe for most appliance plastics and rubbers when used sparingly as directed
• Commonly used during seal replacement, hinge service, and routine maintenance

• One 2 oz tube of silicone grease

• Apply a thin, even layer to clean, dry surfaces; avoid excess that can attract dirt
• Use gloves and avoid contact with skin and eyes; wash thoroughly after use
• Do not use on electrical contacts or high-temperature surfaces unless specified by OEM
• Follow appliance manufacturer instructions and replace seals or components as recommended