Tecumseh Parts

The Dryer Gas Valve Coil Kit is an OEM replacement part for Whirlpool dryers, as well as Kenmore and Samsung dryers. It is a set of coils that control the flow of gas fuel to the burner. The gas valve regulates the precise amount of gas needed to properly combust and generate heat for drying clothes. 

Causes of a bad gas valve coil can be wear and tear from regular use, lime or mineral buildup on the coils over time, or physical damage to the coils.

Symptoms of a bad gas valve coil kit include:

• Inconsistent or incomplete drying  
• Slow or intermittent drying
• Burning smell from the gas dryer
• Improper burner ignition or non-ignition

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This bake element supplies the lower-oven heat your range or wall oven needs for baking and roasting. Replace it when the oven won't heat properly in Bake or the element shows visible damage.

• Provides primary heat from the bottom of the oven during Bake cycles
• Helps maintain even, consistent oven temperature
• Common failure symptoms: no heat in Bake, slow preheat, uneven or undercooked results
• Visual signs of failure: element is blistered, cracked, or broken

• Disconnect power at the breaker and allow the oven to cool completely
• Access from inside the oven; remove mounting screws, pull the element forward, and move the two wire leads to the new element one at a time
• Support wires so they don't slip behind the liner; ensure snug terminal connections
• Restore power and run a short Bake cycle to verify operation

This control display board is the appliance's user-interface module that operates the front control panel and display, giving visible status and responding to user input. Replacing it fixes display and control issues safely and simply. What it does:

• Provides the visible display and interprets button/touch inputs so the appliance responds to selections.
• Can produce unresponsive or intermittent buttons/touch controls and erratic indicator lights.
• May trigger control errors or prevent cycle selection if damaged.

• Disconnect all power before starting — turn off breaker or unplug the appliance.
• Handle the board carefully and avoid static discharge; use a grounding strap if available.
• Remove and reattach wire connectors and mounting hardware gently; note connector orientation.
• Reconnect power and verify functions before reassembling trim or covers.

This round cooktop surface element provides a direct heat source for electric ranges, restoring one burner's ability to heat cookware evenly. It's a straightforward replacement for a damaged or non-heating burner element. What it does:

• Heats cookware on an electric range cooktop so pots and pans can reach cooking temperatures
• Replaces a cracked, burned-through, or non-functioning surface element to restore burner operation
• Helps eliminate intermittent or no-heat symptoms on the affected burner
• Works with the range's existing terminal block and controls when compatible

• One cooktop surface (round) element

• Disconnect power to the range at the circuit breaker before starting work
• Remove the damaged element from its terminal connections and lift out; install the new element by seating terminals fully and testing power
• Use care to avoid scratching the cooktop surface and verify element compatibility with your model

This is an authentic replacement bowl drain washer for use with lawn mower engines and other types of lawn and garden equipment. The washer is used to help seal the connection between the float bowl and the bowl drain screw in the engine. Although the washer is made from metal, it may still need to be replaced at some point if it becomes corroded, bent, or otherwise damaged. This would mean that it no longer provides a proper seal and that there could be leaks. Owners should periodically take the time to inspect the bowl drain washer, along with other elements of their machine, and replace them as needed. It may be a good idea to have several of the washers on hand. The genuine OEM replacement bowl drain washer is sold individually. It will work with a range of different types of machines including lawn mowers, snowblowers, pressure washers, and other small engines. Compatible brands include Craftsman, Toro, Tecumseh, Lawn-Boy, MTD, and Briggs & Stratton. Buyers should always be sure they are choosing the correct washers for their needs.

This air cleaner cover is designed for use with lawn and garden equipment with small engines like lawnmowers and tillers. It is made of durable black plastic and fits over the air filter to offer extra protection, keeping debris and dirt out of the motor as those contaminants can create engine performance issues. The air cleaner cover has a set of ventilation slots to allow air passage. Through ordinary use, it can be damaged and will need replacement.A quick visual inspection of the air cleaner cover will indicate whether the part has been damaged or is broken. It may have broken tabs or be cracked. If there are holes in the material, it will need to be replaced. Removal and installation of the part do not require additional tools.This air cleaner cover is an authentic OEM replacement part sourced directly from the manufacturer. It is sold as an individual component. The cover is compatible with lawnmowers, pressure washers, and tillers manufactured by Simplicity, Briggs & Stratton, Cub Cadet, and Tecumseh.

This is a replacement for a carburetor in lawn and garden equipment engines. The carburetor is responsible for creating the air and fuel mixture that goes into the engine to create the combustion and start the machine. It contains several parts and can become worn, damaged, or even just clogged over time. In many cases, it's more affordable and easier to replace or repair a carburetor than it is to replace the entire unit. Be sure to use an OEM part like this to do the job. To replace the carburetor, simply allow the engine to cool and then remove the old one from the engine. Then, replace the new unit, screw it into place, and connect the fuel lines. Test it by pouring fuel straight into the carb and starting the engine. If it fires and wants to stay running, the problem is solved. This OEM carburetor replacement is compatible with several models of 4-cycle engines from Tecumseh. It comes as an entire assembly and is sold as an individual unit. Other parts and hardware will require an additional purchase.

This carburetor repair kit is made to be used with several types of lawn and garden equipment with small engines. It has all the replacement parts needed to get a generator or snowblower running again if there is a problem with the carburetor. The carburetor is a component inside the lawn equipment that controls the mixture of air and fuel that ignites within a cylinder to cause the engine to run.If the lawn and garden equipment refuses to start up even with a full tank of fuel, this is one of the primary signs that the carburetor has gone bad and will need repairs or replacement. Remove the air filter and pour a small amount of fuel into the carburetor to test where the component is working the way it should be. If the engine turns on but then dies after a short period of time, there is likely an issue with the carburetor. It will need to be rebuilt or replaced.This is a genuine OEM replacement carburetor repair kit directly sourced from the manufacturer. It is compatible with snowblowers and generators manufactured by Craftsman, Tecumseh, Cub Cadet, Toro, and Husqvarna. Each repair kit is sold individually and may require basic tools for installation.

This screw is built specifically to secure the choke bracket on a variety of snowblowers and tillers. Screws can be used in all sorts of situations to hold two components together for protection and security. Over time, the screw can become stripped, corroded, or damaged. When this occurs, the screw will need to be replaced.A visual inspection will determine whether the screw needs to be replaced. First, make sure the equipment is turned off and the spark plug wire has been disconnected. Look at the screw and clean it off to determine whether it has been damaged or broken. Sometimes, the screws can become loose and will need to be replaced to continue securing the choke bracket. The first step is to use a screwdriver or a nut removed to take out the damaged screw. Replace it with a new screw.This is a genuine OEM replacement part that is directly sourced from the manufacturer. The screw is sold as an individual part. It is made to be compatible with snowblowers and tillers manufactured by Lawn-Boy, Toro, Cub Cadet, and Tecumseh.

This intake manifold allows an engine to get the air it needs in order to run properly. Any engine runs on three things - air mixed fuel, the sparks, and combustion. It is the intake manifold that delivers the air to all of the cylinders and guarantees function. This gasket is used to replace a pre-existing intake manifold gasket that has dried out or has failed to keep the intake manifold properly sealed to the engine. This may allow air leaks or uneven air pressure in the cylinders, affecting how well the engine runs. Any gasket may wear out with time and use, and replacing the a failed intake manifold gasket with this OEM part is one way to ensure that the engine is again running at optimal levels. The repair requires wrenches, socket sets, and the appropriate components for the engine in question. This is a gasket for an intake manifold on an array of lawnmowers, lawn tractors, and snowblowers made by Tecumseh, Toro, MTD, and Lawn-Boy, and others. This high-quality intake gasket ships individually and is made of composite materials.

This is a replacement carburetor gasket. The gasket plays an important role in the carburetor. It helps to ensure that there is no additional air getting into the carburetor. It also ensures no dirt or other debris makes it into the carburetor. If the gasket is not working properly or has been damaged, air and other elements that get into the carburetor could cause the engine to run rough. It could also make it more difficult to start the engine.Over time, the carburetor gasket will wear down and will need to be replaced. Gaskets will dry out and crack the longer they've been used. There is also the possibility that the gasket has not been seated properly, which would require repair. Whenever owners are servicing the carburetor, they should make it a point to replace the gaskets, even if they appear to be in serviceable condition.This gasket is an OEM replacement part sourced directly from the manufacturer. It will work for certain models of carburetors from Tecumseh and Craftsman. Each of the gaskets is sold individually.

The oil seal is designed to stop fluid from leaking out, as well as to ensure that dirt and other debris do not make their way into the oil. When applied properly, it should create an impermeable seal. It also provides spacing between the crankcase and the crankshaft. If the oil seal has been damaged or has degraded because of wear and tear, it will need to be replaced. Some of the signs that the oil seal might be bad include leaks or an engine that is not performing properly. Users might also notice that the machine is going through oil quickly. This is an authentic OEM product that is sold individually. The oil seal can be used with many types of lawn and garden equipment including lawn mowers, snowblowers, tillers, pressure washers, wood chippers, generators, and other small engines. Compatible brands including Briggs & Stratton, Simplicity, Snapper, MTD, Lawn-Boy, Tecumseh, Cub Cadet, Toro, and Craftsman.

This is a throttle link made to be used by many types of lawn and garden equipment. It is a metal part that connects the carburetor to the throttle controls. If the throttle link is damaged or broken, it will not be possible to change the speed of the tool's engine. In some cases, if the throttle link is malfunctioning or broken, the equipment may not run at all.The throttle link is made of durable materials but it can be weakened by continued use due to stress and vibrations. This can cause the link to break down and stop working. If this occurs, it will need to be replaced. A screwdriver or an Allen wrench will be required to handle the replacement process. The throttle link will need to be removed from the throttle body so the replacement part can be installed.This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The throttle link is created for use with snowblowers, lawnmowers, tillers, pressure washers, and generators made by Briggs & Stratton, Tecumseh, Cub Cadet, Craftsman, MTD, Simplicity, and Toro.