Weedeater Carburetor

The carburetor kit has a metal body that is designed to withstand high temperatures, a rubber primer bulb, and a plastic throttle lever. The carburetor is an integral part of engines in lawn and garden equipment. This is where the air and fuel will be mixed before being sent into the engine. The air comes in through the intake tube, and it flows into a smaller tube, where the fuel is injected through small holes in the carburetor body. Then, the two are mixed and released into the engine through a butterfly valve, which controls the amount of fuel going to the engine for optimal performance. The carburetor can become clogged over time or even be broken or damaged. If the engine is not running properly, the carburetor may need to be replaced. This is a simple replacement that only requires a screwdriver. Make sure to always disconnect the spark plug and wear gloves when performing engine repairs. This kit can be used with several models of lawn and garden equipment, including brands like Weed Eater, Paramount, Poulan, Jonsered, and Husqvarna.

This certified OEM replacement part is a carburetor kit for a gas-powered leaf blower engine. For gas to ignite in an engine, there has to be the right amount of air in the system. Without oxygen, the spark won't light and the gasoline will not ignite. A carburetor is responsible for maintaining the right balance of air and gasoline. Therefore, without a properly functioning carburetor, the engine will also not function properly. Carburetors begin to break down over time because of built up exhaust and gunk in the engine. As this grime builds up, the carburetor cannot get enough air and the balance is thrown off. While carburetors can sometimes be cleaned, if it has become overly clogged or damaged, it will need to be replaced. Signs of a faulty carburetor include shakiness and black smoke, backfiring, hard starts, or an engine that will not start at all. Replacing a leaf blower's carburetor requires the crankcase line, primer line, fuel line, air filter, and throttle linkage to all be disconnected using pliers and a screwdriver. This part is intended for Craftsman, Poulan, Weed Eater, and Husqvarna leaf blowers and is sourced from the original manufacturer. It ships individually.

This part is a replacement carburetor assembly. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or defective carburetor in leaf blowers.Carburetors are critical for the proper functioning of an internal combustion engine as they enable the proper mixture of air and fuel for ignition. If the carburetor is faulty, the equipment may not run properly or may not turn on at all. Thus, the carburetor will need to be replaced. When working on or near an engine it's important to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this carburetor assembly, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality materials. This carburetor assembly can be used with different models of leaf blowers that have been manufactured by Husqvarna, Poulan, and other brands. Part sold individually.

Blowers are often designed with gas-powered engines. When a blower has adequate fuel, but the engine does not start, it could be a problem with the carburetor. This is the part that mixes air and fuel to send into the engine. If an engine starts and dies or fails to start at all, the carburetor may need replacement. This replacement for a blower carburetor works with Craftsman and Poulan blowers, and is compatible with a long list of models. This is an OEM replacement part that features a metal body and which incorporates the rubber primer bulb necessary to begin the starting process. It ships individually and is will require pliers and a screwdriver to make the repair.

This replacement part is a carburetor assembly and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This carburetor assembly is used in leaf blowers and snow blowers and is part of the engine. This part is one of the most important parts of the machine and is responsible for allowing it to run smoothly.A new carburetor assembly might be needed if the current engine is slow to start, slow to stop, or won't start at all. This can be due to a malfunctioning carburetor and create problems within the machine. Be sure the appliance is completely powered down before replacing this part. work gloves are recommended to ensure safety during any type of repair.This carburetor is sold individually and is a genuine OEM replacement part. This is also sourced directly from the manufacturer.

This throttle linkage is a genuine Husqvarna part, sold individually. This throttle linkage can be used as a replacement part in a leaf blower. The purpose of the throttle linkage in a leaf blower is to affix the throttle control to the carburetor so that the carburetor and throttle can work in unison to provide power to the engine and control the speed of the appliance as it is propelled forward across a variety of surfaces.The throttle linkage in a leaf blower might need to be replaced if the throttle linkage has permanently detached from its stable position within the throttle controls of the appliance or if the throttle linkage has suffered irreparable damage. If the throttle linkage is not serving its function and cannot be repaired, the throttle linkage should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This throttle linkage is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Weed Eater, Poulan, and Poulan Pro.

Here is a replacement carburetor assembly specifically for use with handheld blowers. The carburetor is the part of the machine responsible for mixing the air and the fuel before the mixture goes to the engine. It helps to ensure a good start and performance of the engine each time the blower is fired up and used. The carburetor can become damaged or it could start to wear out over time. When this happens, it means that engine performance is likely to suffer. In some cases, the engine might stall. It's possible to test the carburetor by ensuring there is fresh fuel inside, removing the air filter, and adding a teaspoon of fuel to the carburetor. Pull the starter rope and see if the engine starts and then dies immediately. If that's the case, it means that the carburetor is likely the problem and will need to be replaced. This is a genuine OEM replacement carburetor for handheld blowers. It is sold individually and is compatible with certain models from the brands Husqvarna and Weed Eater.

This replacement part is a carburetor adapter and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. This carburetor adapter, also referred to as a carburetor spacer, is able to increase the distance between the intake of the bottom of the carburetor. This reduces the velocity of the intake charge which allows the entire appliance to run smoothly and efficiently.A malfunctioning adapter might cause additional friction inside the machine, so be aware of extra heat. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This genuine carburetor repair kit is designed for use in select trimmer engines. The carburetor is responsible for combining the gas and air mixture that will go into the engine. Fuel and air flow into the carburetor through filters to remove any potential debris or particulates. Then, they are passed through a series of tubes and diaphragms and mixed together in the inner tube before being released into the engine through a butterfly valve. Over time, the high heat and constant pressure can damage the gaskets, diaphragms, and other parts of the carburetor. It may be necessary to replace everything with this carburetor repair kit that includes multiple components. This genuine OEM carb kit is compatible with select lawn and garden trimmers from Craftsman, Poulan, Weed Eater, and Jonsered. There are more than 50 compatible models available that can use this kit. This carburetor repair kit comes with 16 pieces in total, including the gaskets and diaphragms, the primer bulb and primer bulb assembly, and other necessary hardware. It is sold as a single unit. Always cool the engine completely and work in a well-ventilated area when performing carb rebuilds and replacements or other engine repairs.

The genuine replacement primer bulb covers the primer base and plunger on specific leaf blower models. Before starting the leaf blower, the primer is pushed to allow fuel to flow into the carburetor to assist in a smooth engine start. It can also make starting the equipment easier after it has been sitting for a period of time. The bulb is made of plastic and exposed to the elements, so over time it can become cracked, worn, or even completely lost. Without it, the engine cannot be properly primed before operating and therefore will not run as well. Replacing the bulb with a genuine OEM model like this should be done as soon as possible. This OEM primer bulb is manufactured by Husqvarna and can be used for a variety of leaf blowers that are manufactured by the brand. This model is also compatible with Poulan, Craftsman, and Weed Eater products. The bulb is made of durable rubber and may require a screwdriver for replacement to assist in fitting the bulb into place. This unit is sold individually and does not include the primer base assembly or any hardware.

This kit includes all parts necessary to repair the carburetor on certain models of small engine outdoor power equipment.Internal combustion engines require a proper ratio of air to fuel in order to run. The carburetor is responsible for sending a combination of fuel and air to the motor for ignition. Because the carburetor is used every time the engine is started, it can deteriorate over time and may need to be repaired or replaced. Signs of a worn-out or deteriorating carburetor include backfiring, overheating, excessive black smoke, and reduced engine performance. This carburetor repair kit is a genuine OEM replacement part that has been sourced directly from the manufacturer. This carburetor repair kit can be used to fix various different models of Husqvarna, WeedEater, and Poulan blowers, trimmers, and hedge trimmers. Please note this part is sold individually.

This carburetor kit is a genuine Husqvarna part that can be used as a replacement part inside snowblowers, wood-chippers, lawn mowers, and other outdoor appliances. The function of the carburetor kit in a small engine is to mix the air and the fuel together at a proper ratio for combustion before they are both passed into the engine via the network of valves. This carburetor kit includes the carburetor and the primer bulb. If the carburetor kit is indeed malfunctioning or in a state of disrepair, there are signs to look for in confirming the issue. Pour a spoonful of fuel directly into the carburetor and try to start the engine with the recoil starter. If the engine fails after a quick false start, the carburetor kit might be in need of repair or total replacement. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This carburetor kit is compatible with the brands Husqvarna and Weed Eater.

This is a choke control which is used on various types of trimmers for yards and gardens. It is made of durable plastic and is responsible for letting fuel go into the engine whenever the motor is running. The choke control comes with a steel ball, metal valve door, and a spring. If the choke control is damaged or stops working, it will need to be replaced. The engine will not receive fuel if the part is malfunctioning or otherwise damaged.This is a fairly easy replacement project that requires no tools other than a screwdriver. First, make sure the trimmer is turned off to prevent any accidents. Place it on a flat surface while making the replacement. The first step is to remove the carburetor from the engine. At that point, the choke control can be removed and the new replacement part can be installed. Reinstall the carburetor and the equipment will be ready for use.This choke control is a genuine OEM replacement part that is directly sourced from the manufacturer. It comes as an individual part. The choke control is designed to be used in string trimmers and hedge trimmers created by Craftsman, Poulan, and Weed Eater.