Douglas F Camano Island , WA January 09, 2018 Appliance: Model KITCHENAIDE MOD # 10224430 Door on detergent dispencer would not stay fastened Initially, I reviewed the comments submitted by previous buyers and then ventured into the "You Tube" Zone. I found the comments submitted by previous buyers both interesting and contradictory. My dishwasher is a ten (10) year old Kitchen Aide (Model# 10224430). The first six or seven reviews stated you need to remove six (6) to ten (10) screws to remove the door and access the detergent rinse dispenser. They are wrong. See the actual number below. CAUTION: Before starting any removal procedures, DO NOT FORGET to DISCONNECT the dishwasher breaker!! This is IMPORTANT!!! You will need the following tools to complete the overhaul: #15 Torque screw driver or socket driver. 3/16" Socket or wrench. (I used a socket driver with 1/4: drive) Here is an actual breakdown of the number of screws: Four (4) 3/4" screws on each side of the dishwasher. Two (2) 1/2" screws on each side at the very bottom of the dishwasher. Four (4) 1-1/2" screws of the top of the door. Note: All screws have #15 torque heads. After removing all ten (10) screws, separate the top part of the door frame and remove the front panel being careful to not over stress or pull on the ribbon cable attached to the panel. (Note: There is no need to disconnect the ribbon cable just proceed with caution. Now you can start to remove the old dispenser from the inside door panel. Start by removing the six (6) 3/16" screws from the dispenser. There is a rectangular frame and black rubber moisture / vapor barrier cover that protects the unit and they will both be freed from the dispenser. There are two (2) tabs located at the top and bottom of the dispenser that need to be pried upward to fully facilitate removal of the unit. To remove the unit from the door I needed to hold the unit with my hand, push it in and turn at an angle to remove. Carefully disconnect the wiring harness plug and the dispenser will now be totally free. Reassembly is basically just reversing the removal process with a few caveats: The wiring harness will only plug in one (1) way. Do not force it! Do not forget to reinstall the protective rubber boot and frame over the new dispenser. The exterior door panel must be lifted over two (2) brackets on each side of the door to fit properly. Turn the fuse breaker back on after installation. Once you have assembled all the required tools the job should be easily completed in 60=90 minutes. Read More... Do-It-Yourself Rating: Repair Time Estimate: 1-2 hours Tools: Nut Drivers, Screwdrivers
Reed W Eldon , MO November 11, 2014 My dishwasher detergent dispensor door was not opening during wash cycle and the control panel was loose because the plastic mounts for the screws were broken I ordered a new detergent dispenser and control assembly, watched a few videos on you tube and dived in. The repairs were pretty simple once I got started and while I was doing this I went the extra step and cleaned out the drain. I would suggest doing this annually. Pretty simple to do and only 5 screws to get to the drain and the grinder. I found plastic and several other things that would not allow the dishwasher to drain properly and probably part of the problem of dishes not getting clean. It took less than an hour to do all the repairs and maintenance. Watch the you tube videos and from there almost anyone can figure out. Read More... 13 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Pliers, Screwdrivers
Alan H Waterford , MI March 12, 2014 Soap dispenser didn't work. I watched a video on YouTube and took it from there. Not a big deal. Read More... 7 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Socket Set
Debra F New Smyrna Beach , FL April 01, 2015 Soap dispenser didn't open Ordered soap dispenser unit & installed it myself. Saved a lot of money & my dishwasher working perfect again! Read More... 6 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 2+ hours Tools: Nut Drivers, Screwdrivers
David D Rochester , NH June 15, 2015 Appliance: KitchenAid Undercounter Dishwasher KUDI02IRBS2 Clip that held dispenser door closed near breaking point It was probably a dozen or so washes from breaking off completely. The repair was quite simple - remove the star screws holding the front panel (3 on each side), remove the panel, remove the wire connector, unscrew the dispenser (6 hex screws) and replace in reverse order. Took 20-30 minutes. Read More... 3 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers, Socket Set