Parts for Whirlpool ZDIS15CSSM: 01 - Cabinet Liner And Door Parts

Size: 8-18 x 1 1/4 inch.

Replacement mounting spacer for ice makers. Maintains proper clearance and alignment between components. Replace if cracked, broken, or missing.

Size: 8-18 x 1/2 inch.

Ice maker door won't stay closed or seal properly? This door catch assembly restores secure latching to maintain proper temperatures and operation.

White hole plug covers unused openings in your refrigerator cabinet. Replace when missing or damaged to seal gaps and protect internal components.

White button plug cap for refrigerators. Covers screw holes or mounting points on control panels and exterior surfaces. Replace when missing, cracked, or discolored.

This screw grommet anchors a screw in thin appliance panels so trim, covers, or consoles stay tight. It provides a snug, vibration-damping fit where a standard screw could loosen or strip over time.

• Creates a captive insert so a screw can securely fasten to sheet metal or plastic panels
• Replaces a worn, cracked, or missing grommet to restore proper screw retention
• Helps reduce panel rattles and movement from vibration
• Typical signs of failure: screw won't tighten, panel or trim feels loose, grommet falls out

• Disconnect power and shut off gas/water as applicable before servicing
• Remove the screw and lift out the old grommet; clear debris from the opening
• Press the new grommet straight into the hole until fully seated and flush
• Reinstall the screw and tighten gently to avoid deforming the grommet

Bottom door gasket for ice makers. Seals lower door edge to maintain temperature and prevent frost buildup. Replace if worn, cracked, or leaking air.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This 15-inch door gasket is a direct-replacement sealing gasket that restores a tight door seal to the appliance, helping reduce heat and air leaks for more consistent temperature control and improved efficiency. What it does:

• Seals the door edge to prevent loss of heat, steam, or cooled air during operation.
• Helps maintain consistent internal temperature for proper cooking/drying/operation.
• Common symptoms it can fix: visible cracks, tears, flattening, gaps, or a door that does not close flush.
• Reduces stray heat or moisture around the appliance that can indicate a worn seal.

• Disconnect power (and gas if applicable) and allow the appliance to cool before servicing.
• Remove the old gasket carefully and inspect the sealing channel for debris or damage before installing the new gasket.
• Start installation at the top and press the gasket evenly into the channel, working around the door so the flange seats fully; replace any fasteners or clips as needed.
• Do not stretch, trim, or modify the gasket unless OEM instructions explicitly direct it; the appliance diagram for orientation.

This part has been discontinued and is no longer available

Replacement top hinge for ice maker doors. Installs at the upper door corner. Order if your original hinge is broken, cracked, or no longer holds securely.

Hinge shim for ice makers. Installs between hinge components to maintain proper door alignment. Replace if worn, cracked, or missing for smooth operation.

Replacement cover assembly for ice makers. Installs to replace cracked, broken, or missing covers. Protects internal components and restores appearance.

White handle mounting screw for ice makers. Secures the door handle in place. Order a replacement if your original screw is stripped, lost, or damaged.

Black mounting screw for ice maker door handles. Secures handle to door panel. Replace if screw is stripped, missing, or no longer holds handle firmly.

Black plastic right side endcap filler for freestanding ice makers. Replaces cracked, broken, or missing endcap trim pieces. Installs on right side.

Color: Black. This is the left side endcap filler. For right side use 2185656B.

Wiring channel for ice makers. Organizes and protects electrical wires inside the unit. Replace if cracked, broken, or missing to secure wiring properly.

Water pooling under your ice maker? A cracked or damaged drain tube causes leaks and floor damage. This 15-inch tube restores proper drainage flow.

The Ice Maker Scoop is an OEM component specifically designed for Whirlpool ice machines. As an included accessory, it provides a sanitary and convenient way for users to fetch ice from the storage bin.

The scoop is strategically designed with an ergonomic handle and wide opening bowl shape. This facilitates easy scooping and transport of ice cubes without spillage or crumbling. Its food-safe materials maintain hygienic conditions in the storage area. 

Symptoms of a faulty scoop include:

• Cracks or breaks that compromise the scooping surface 
• Leaks or spills of ice when trying to scoop
• Sharp edges that risk cuts or scratches
• Warping or loosening of the handle attachment over time

This OEM Whirlpool scoop is also compatible with some Scotsman and Manitowoc ice machines. Replace yours today to restore safe and hygienic ice retrieval from the storage bin.
 

Size: 8-18 x 5/8 inch.

Secures flexible tubing to fittings on water and drain lines. Replace when clamps lose tension or you find leaks. Confirm fit with your model number.

Bottom door hinge for freestanding ice makers. Mounts at the base of the door to provide pivot support. Replace if cracked, bent, or worn from use.

Secures your ice maker door to the hinge assembly for smooth pivoting. Replace if worn, damaged, or causing door misalignment, rubbing, or sagging.

Size: 8-32 x 1/2 inch.

Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.

Size: 8-18 x 3/4 inch.

Secures panels, brackets, and internal components in appliances. Replace missing, stripped, or corroded screws to restore secure assembly and alignment.

This scoop holder is a replacement freezer-door accessory that keeps the ice scoop secure, hygienic, and within easy reach. It restores the built-in storage location so your scoop stays put and ready when you need it. What it does:

• Provides a dedicated clip/mount to hold the ice scoop on the freezer door or bin
• Keeps the scoop off surfaces to reduce contamination and dripping
• Prevents the scoop from falling out when opening or closing the door/bin
• Restores proper storage when the original holder is cracked, broken, or missing

• Typically snaps into the designated slot on the freezer door or bin; no special tools required for most installs
• Align the holder and press firmly until it clicks into place; replace cracked or broken surrounding tabs if necessary
• Handle gently to avoid damaging door bins or trim during installation

Size: 10-32 x 5/8 inch.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

Electrical shield for ice makers. Protects wiring and electrical components from moisture and debris. Replace if cracked, damaged, or missing.

White front grill panel for freestanding ice makers. Replace this cosmetic part if your original grill is cracked, discolored, or missing.

Black front grill panel for ice makers. Covers the front exterior of your unit. Replace if cracked, discolored, or damaged to restore appearance.

Size: 8 x 1-1/4 inch.