Parts for Gaggenau EB170-610: 01 - Cavity, Internal Top Panel & Door Parts

This part has been discontinued by the manufacturer and is no longer available.

Appliance overheating or shutting off unexpectedly? This 253°F thermal protector prevents damage by cutting power when temperatures exceed safe limits.

Structural angle bracket for appliance mounting and support. Replace if bent, cracked, or missing to restore proper alignment and secure installation.

This 750 ohm fixed resistor restores the correct resistance on the appliance control circuit so the control board can operate reliably. Use it to replace a burned or open resistor that interrupts normal electrical function. What it does:

• Provides a precise 750 O resistance value used in control and sensing circuits
• Limits or drops voltage to protect downstream components
• Restores stable control-board signals when the original resistor is open or damaged
• Commonly linked to symptoms like intermittent operation, control errors, or failure to start

• Disconnect power to the appliance before attempting service
• Handle the resistor and circuit board carefully to avoid damage; observe ESD precautions
• Confirm orientation and solder joint quality when installing; use proper tools and techniques

This rubber grommet cushions and seals appliance components to reduce vibration and prevent chafing where hoses, shafts, or fasteners pass through panels. It restores a proper seal and helps stop rubbing-related wear and noise. What it does:

• Cushions motor, pump, or assembly mounts to reduce vibration and noise
• Seals openings to help prevent rubbing and abrasion of hoses or wiring
• Keeps components aligned and reduces movement that can cause wear
• Commonly replaced when you see wear, cracking, splitting, or persistent vibration/noise

• One rubber grommet

• Disconnect power (and water if applicable) before accessing internal components
• Access the faulty grommet location per your model's service instructions; remove and compare the old grommet to fit
• Press new grommet into place; ensure proper seating around the hose/shaft or mounting point

This mounting clip secures panels and small components to the appliance frame to prevent movement and vibration. It's a simple, durable replacement that restores proper fit and reduces rattling or loose trim. What it does:

• Holds trim, panels, or small assemblies in place to maintain correct alignment
• Helps stop rattling, vibration noise, and loose-fitting parts
• Restores the original fastener function after a broken or missing clip
• Fits into a designed slot or stud for a secure snap-in connection

• Disconnect power and water before starting any repair
• Remove the affected panel or trim to access the clip; gentle prying may be required
• Align clip with the factory slot or stud and press until it snaps into place
• If clip is brittle or hard to seat, replace any adjacent damaged fasteners for a secure fit

This rubber mounting grommet cushions and secures a dishwasher component to reduce vibration and wear, helping restore quieter operation and proper alignment. It's a small but important part for stabilizing mounted parts and protecting wiring or hoses. What it does:

• Cushions and isolates vibration between a mounted component and the chassis to reduce noise and movement
• Protects hoses, wires, or other parts from chafing where they pass through or contact openings
• Helps maintain proper alignment of the attached component to prevent excess wear
• Common symptom fix: reduces rattling or vibrating noises and prevents rubbing marks at the mount

• Disconnect power and, if applicable, water supply before starting any repair
• Access may require removing outer panels or the component being mounted; keep fasteners organized
• Verify correct orientation and full seating of the grommet before reassembling
• If multiple grommets are used at the same location, replace all like-for-like for consistent support

This convection fan motor circulates oven air to promote even heat distribution for baking and roasting. Replacing a failed motor restores airflow so your oven can maintain more consistent cooking temperatures. What it does:

• Spins the convection fan to move hot air throughout the oven cavity for more even cooking and browning
• Common symptom: uneven baking or roasting where food cooks hotter in some areas
• Common symptom: fan doesn't run, hums, or runs intermittently
• Common symptom: increased vibration or loud noise coming from the oven interior

• Disconnect power to the appliance before starting any service to avoid shock hazard
• Access usually requires removing oven panels or the rear cover; handle sharp sheet metal carefully
• Match part number and connector type before installation; secure mounting and wiring per OEM guidance

This convection ring element supplies the heat for the oven's convection bake and roast cycles. Replacing a failed element restores even convection performance so foods cook properly across multiple racks.

• Provides the heat source for convection modes; the fan circulates air across this ring for uniform baking
• Common symptoms of failure: no heat in convection, very long preheat, or uneven results during convection cycles
• Visual clues include cracks, blistering, or burn-through on the element band
• Electrical clue: element tests open/infinite (OL) with a multimeter when power is disconnected

• Disconnect power at the breaker before servicing; this is a high-wattage circuit
• Access varies by model: remove the rear panel or the interior convection cover to reach the element and terminals
• Note wire locations and transfer leads to the new element one at a time
• Ensure the element sits flat and does not contact the cavity walls; tighten mounting screws snugly

Seals the heating element opening to maintain proper heat and prevent leaks. Replace when worn or damaged to restore efficient operation. Confirm fit.

This is a metal grate that sits over a cooktop burner on a range, providing a stable surface to support pots and pans during cooking. It distributes weight evenly and allows heat to reach cookware from the burner below. Replace this grate if it is cracked, warped, rusted, or if its supports are worn down causing cookware to sit unevenly.

This is the worktop surface that sits on top of the range body, providing the main cooking surface and housing for burners or heating elements. It serves as the structural and aesthetic top panel of the unit. Replace this part if it is cracked, chipped, warped, or otherwise damaged from heat exposure or impact.

This genuine OEM part is an oven door handle mounting bracket. The oven door handle mounting bracket secures the handle to the oven door allowing the user to open and close the oven. Over time, these brackets can loosen, causing the handle to no longer be secured to the door. If the brackets are no longer holding the handle in place, then they might need to be replaced. Luckily this is a simple repair. To replace the brackets, open the oven door and locate the screws holding the brackets in place. Remove the screws and damaged brackets. Replace the brackets with the new ones and tighten the screws to secure the handle. Make sure to test if the handle is secured tightly to the oven door. This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador ovens.

This genuine OEM part is an oven door handle mounting bracket. The oven door handle mounting bracket secures the handle to the oven door allowing the user to open and close the oven. Over time, these brackets can loosen, causing the handle to no longer be secured to the door. If the brackets are no longer holding the handle in place, then they might need to be replaced. Luckily this is a simple repair. To replace the brackets, open the oven door and locate the screws holding the brackets in place. Remove the screws and damaged brackets. Replace the brackets with the new ones and tighten the screws to secure the handle. Make sure to test if the handle is secured tightly to the oven door. This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador ovens.

This genuine OEM part is an oven door handle mounting bracket. The oven door handle mounting bracket secures the handle to the oven door allowing the user to open and close the oven. Over time, these brackets can loosen, causing the handle to no longer be secured to the door. If the brackets are no longer holding the handle in place, then they might need to be replaced. Luckily this is a simple repair. To replace the brackets, open the oven door and locate the screws holding the brackets in place. Remove the screws and damaged brackets. Replace the brackets with the new ones and tighten the screws to secure the handle. Make sure to test if the handle is secured tightly to the oven door. This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador ovens.

This genuine OEM part is an oven door handle mounting bracket. The oven door handle mounting bracket secures the handle to the oven door allowing the user to open and close the oven. Over time, these brackets can loosen, causing the handle to no longer be secured to the door. If the brackets are no longer holding the handle in place, then they might need to be replaced. Luckily this is a simple repair. To replace the brackets, open the oven door and locate the screws holding the brackets in place. Remove the screws and damaged brackets. Replace the brackets with the new ones and tighten the screws to secure the handle. Make sure to test if the handle is secured tightly to the oven door. This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador ovens.

This is a holder component that secures the oven door in place during operation. It helps maintain proper door alignment and ensures a tight seal when the door is closed. Replace this part if your oven door feels loose, does not latch properly, or fails to stay in the correct position.

This adhesive ground terminal label identifies the appliance's designated grounding connection, helping homeowners locate the correct terminal quickly for safe wiring and service. Durable, self-adhesive marking for internal appliance panels. What it does:

• Marks the chassis ground/earth connection so the grounding point is clearly visible
• Helps reduce wiring errors during service or installation
• Improves safety by making the ground terminal easy to find
• Intended for use on interior appliance sheet metal or electrical access panels

• Disconnect power before opening access panels or working near electrical components
• Clean and dry the mounting surface; peel adhesive backing and press firmly into place
• Position carefully before applying; adhesive is permanent and not intended for repeated repositioning
• Use only on appropriate interior panel surfaces away from high-heat components

M4 square nut for securing components in appliances. Replace if stripped, corroded, or missing to properly fasten panels and parts during assembly.

Replace a burned-out oven light with this 120V, 15W bulb. It restores interior illumination so you can clearly monitor cooking progress through the window, helping maintain temperature and consistent results.

• Illuminates the oven cavity during preheat, baking, and broiling
• Direct replacement for a failed or dim bulb
• Helps you check food without opening the door
• Common signs of failure: light won't turn on, flickers, or filament appears broken

• Disconnect power to the appliance and allow the oven to cool completely before servicing.
• Remove the glass lens/cover to access the bulb; handle glass carefully.
• Install using a dry cloth or gloves; do not overtighten.
• Match the bulb's voltage and wattage to the original; never exceed the rated wattage.

This spacer positions and supports internal components to maintain correct alignment and reduce wear. It helps keep panels and assemblies spaced correctly so moving parts don't rub or bind. What it does:

• Holds components at the proper distance to ensure correct fit and function
• Prevents rubbing, chafing, and premature wear between parts
• Reduces vibration and noise caused by loose or misaligned assemblies
• Can cause misalignment, excessive noise, or binding when damaged or missing

• Disconnect power and water before accessing internal parts
• Replace only with the exact spacer to maintain correct clearance and fit
• Handle small plastic/metal spacers carefully to avoid loss; keep fasteners organized

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.