Parts for Gaggenau EB181-610: 01 - Cavity, Internal Top Panel & Door Parts

This part has been discontinued by the manufacturer and is no longer available.

This 750 ohm fixed resistor restores the correct resistance on the appliance control circuit so the control board can operate reliably. Use it to replace a burned or open resistor that interrupts normal electrical function. What it does:

• Provides a precise 750 O resistance value used in control and sensing circuits
• Limits or drops voltage to protect downstream components
• Restores stable control-board signals when the original resistor is open or damaged
• Commonly linked to symptoms like intermittent operation, control errors, or failure to start

• Disconnect power to the appliance before attempting service
• Handle the resistor and circuit board carefully to avoid damage; observe ESD precautions
• Confirm orientation and solder joint quality when installing; use proper tools and techniques

This oven convection blower motor circulates hot air for even baking and helps cool internal components. Replaces a worn or failed blower motor to restore proper airflow and consistent oven performance. What it does:

• Drives the convection/blower fan to move hot air for more even cooking
• Restores airflow when the oven overheats or cooling is inadequate
• Stops excessive fan noise or vibration caused by a failing motor
• Brings the fan back to life if it won't start or runs intermittently

• Disconnect power to the appliance before starting any repair
• Basic hand tools needed; access typically from the oven rear or interior panel
• Handle the motor and fan blade carefully to avoid bending blades or damaging wiring
• Test operation after installation before reassembling all panels

This rubber grommet cushions and seals appliance components to reduce vibration and prevent chafing where hoses, shafts, or fasteners pass through panels. It restores a proper seal and helps stop rubbing-related wear and noise. What it does:

• Cushions motor, pump, or assembly mounts to reduce vibration and noise
• Seals openings to help prevent rubbing and abrasion of hoses or wiring
• Keeps components aligned and reduces movement that can cause wear
• Commonly replaced when you see wear, cracking, splitting, or persistent vibration/noise

• One rubber grommet

• Disconnect power (and water if applicable) before accessing internal components
• Access the faulty grommet location per your model's service instructions; remove and compare the old grommet to fit
• Press new grommet into place; ensure proper seating around the hose/shaft or mounting point

This mounting clip secures panels and small components to the appliance frame to prevent movement and vibration. It's a simple, durable replacement that restores proper fit and reduces rattling or loose trim. What it does:

• Holds trim, panels, or small assemblies in place to maintain correct alignment
• Helps stop rattling, vibration noise, and loose-fitting parts
• Restores the original fastener function after a broken or missing clip
• Fits into a designed slot or stud for a secure snap-in connection

• Disconnect power and water before starting any repair
• Remove the affected panel or trim to access the clip; gentle prying may be required
• Align clip with the factory slot or stud and press until it snaps into place
• If clip is brittle or hard to seat, replace any adjacent damaged fasteners for a secure fit

This rubber mounting grommet cushions and secures a dishwasher component to reduce vibration and wear, helping restore quieter operation and proper alignment. It's a small but important part for stabilizing mounted parts and protecting wiring or hoses. What it does:

• Cushions and isolates vibration between a mounted component and the chassis to reduce noise and movement
• Protects hoses, wires, or other parts from chafing where they pass through or contact openings
• Helps maintain proper alignment of the attached component to prevent excess wear
• Common symptom fix: reduces rattling or vibrating noises and prevents rubbing marks at the mount

• Disconnect power and, if applicable, water supply before starting any repair
• Access may require removing outer panels or the component being mounted; keep fasteners organized
• Verify correct orientation and full seating of the grommet before reassembling
• If multiple grommets are used at the same location, replace all like-for-like for consistent support

This gasket seals the heating element opening to help maintain proper heat and prevent leaks or debris entry. It restores a tight fit between the element and the appliance cavity for safer, more efficient operation. What it does:

• Creates a heat-resistant seal around the heating element to reduce heat loss
• Helps prevent dust, grease, and moisture from entering the element cavity
• Reduces risk of shorting or arcing caused by gaps or damaged insulation
• Common symptom fix: frayed, cracked, or missing gasket around element flange

• One heating element gasket

• Disconnect power (or unplug) and allow the appliance to fully cool before servicing
• Access the element per your model's service instructions; remove element mounting hardware to replace gasket if required
• Inspect element flange and mounting surface; replace gasket only if it matches OEM shape and seating
• If you see corrosion, burning, or element damage, replace the element as needed and retest after installation

This gasket seals the heating element opening to help maintain proper heat and prevent leaks or debris entry. It restores a tight fit between the element and the appliance cavity for safer, more efficient operation. What it does:

• Creates a heat-resistant seal around the heating element to reduce heat loss
• Helps prevent dust, grease, and moisture from entering the element cavity
• Reduces risk of shorting or arcing caused by gaps or damaged insulation
• Common symptom fix: frayed, cracked, or missing gasket around element flange

• One heating element gasket

• Disconnect power (or unplug) and allow the appliance to fully cool before servicing
• Access the element per your model's service instructions; remove element mounting hardware to replace gasket if required
• Inspect element flange and mounting surface; replace gasket only if it matches OEM shape and seating
• If you see corrosion, burning, or element damage, replace the element as needed and retest after installation

This convection fan motor circulates oven air to promote even heat distribution for baking and roasting. Replacing a failed motor restores airflow so your oven can maintain more consistent cooking temperatures. What it does:

• Spins the convection fan to move hot air throughout the oven cavity for more even cooking and browning
• Common symptom: uneven baking or roasting where food cooks hotter in some areas
• Common symptom: fan doesn't run, hums, or runs intermittently
• Common symptom: increased vibration or loud noise coming from the oven interior

• Disconnect power to the appliance before starting any service to avoid shock hazard
• Access usually requires removing oven panels or the rear cover; handle sharp sheet metal carefully
• Match part number and connector type before installation; secure mounting and wiring per OEM guidance

This genuine OEM replacement part is a heater ring. Also known as the heating element, the heater ring is the coil in the oven that heats up allowing the oven to do its job. Over time, through continuous wear and tear, it is possible for a heating ring to no longer heat properly and sometimes not heat at all. Luckily, replacing this part is a relatively simple process.To replace the heating element, first, make sure the oven is turned off and unplugged. After that, remove the screws of the back panel located on the interior of the oven where the fan is located. The old heater ring will be attached to a single bracket with two screws. Unfasten those screws and remove the old ring by gently pulling it out. Remove the wires attached to the back of the heating element and make sure to take note of their orientation by taking a photo. After the old heater ring has been completely removed, reattach the correct wires to the terminals of the new heating element. Secure the mounting bracket and reinstall the back panel of the oven's interior.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador ovens.

This retaining clip secures components in the espresso machine brew group to hold assemblies in place and maintain reliable brewing alignment. It's a small but essential fastener for stable operation and consistent performance. What it does:

• Secures the brew-group or internal assembly to prevent unwanted movement during operation
• Helps maintain proper seals and alignment that affect extraction and prevent leaks
• A worn or broken clip can allow parts to shift, causing noise, improper brewing, or leaks

• Unplug the machine and allow it to fully cool before servicing
• Handle small clips carefully; use appropriate pliers or tools to remove/install
• Verify proper seating and alignment of the assembly after installation

This gasket seals the heating element opening to help maintain proper heat and prevent leaks or debris entry. It restores a tight fit between the element and the appliance cavity for safer, more efficient operation. What it does:

• Creates a heat-resistant seal around the heating element to reduce heat loss
• Helps prevent dust, grease, and moisture from entering the element cavity
• Reduces risk of shorting or arcing caused by gaps or damaged insulation
• Common symptom fix: frayed, cracked, or missing gasket around element flange

• One heating element gasket

• Disconnect power (or unplug) and allow the appliance to fully cool before servicing
• Access the element per your model's service instructions; remove element mounting hardware to replace gasket if required
• Inspect element flange and mounting surface; replace gasket only if it matches OEM shape and seating
• If you see corrosion, burning, or element damage, replace the element as needed and retest after installation

This gasket seals the heating element opening to help maintain proper heat and prevent leaks or debris entry. It restores a tight fit between the element and the appliance cavity for safer, more efficient operation. What it does:

• Creates a heat-resistant seal around the heating element to reduce heat loss
• Helps prevent dust, grease, and moisture from entering the element cavity
• Reduces risk of shorting or arcing caused by gaps or damaged insulation
• Common symptom fix: frayed, cracked, or missing gasket around element flange

• One heating element gasket

• Disconnect power (or unplug) and allow the appliance to fully cool before servicing
• Access the element per your model's service instructions; remove element mounting hardware to replace gasket if required
• Inspect element flange and mounting surface; replace gasket only if it matches OEM shape and seating
• If you see corrosion, burning, or element damage, replace the element as needed and retest after installation

This genuine OEM part is an oven door handle mounting bracket. The oven door handle mounting bracket secures the handle to the oven door allowing the user to open and close the oven. Over time, these brackets can loosen, causing the handle to no longer be secured to the door. If the brackets are no longer holding the handle in place, then they might need to be replaced. Luckily this is a simple repair. To replace the brackets, open the oven door and locate the screws holding the brackets in place. Remove the screws and damaged brackets. Replace the brackets with the new ones and tighten the screws to secure the handle. Make sure to test if the handle is secured tightly to the oven door. This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador ovens.

This genuine OEM part is an oven door handle mounting bracket. The oven door handle mounting bracket secures the handle to the oven door allowing the user to open and close the oven. Over time, these brackets can loosen, causing the handle to no longer be secured to the door. If the brackets are no longer holding the handle in place, then they might need to be replaced. Luckily this is a simple repair. To replace the brackets, open the oven door and locate the screws holding the brackets in place. Remove the screws and damaged brackets. Replace the brackets with the new ones and tighten the screws to secure the handle. Make sure to test if the handle is secured tightly to the oven door. This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador ovens.

This genuine OEM part is an oven door handle mounting bracket. The oven door handle mounting bracket secures the handle to the oven door allowing the user to open and close the oven. Over time, these brackets can loosen, causing the handle to no longer be secured to the door. If the brackets are no longer holding the handle in place, then they might need to be replaced. Luckily this is a simple repair. To replace the brackets, open the oven door and locate the screws holding the brackets in place. Remove the screws and damaged brackets. Replace the brackets with the new ones and tighten the screws to secure the handle. Make sure to test if the handle is secured tightly to the oven door. This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador ovens.

This genuine OEM part is an oven door handle mounting bracket. The oven door handle mounting bracket secures the handle to the oven door allowing the user to open and close the oven. Over time, these brackets can loosen, causing the handle to no longer be secured to the door. If the brackets are no longer holding the handle in place, then they might need to be replaced. Luckily this is a simple repair. To replace the brackets, open the oven door and locate the screws holding the brackets in place. Remove the screws and damaged brackets. Replace the brackets with the new ones and tighten the screws to secure the handle. Make sure to test if the handle is secured tightly to the oven door. This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador ovens.

This adhesive ground terminal label identifies the appliance's designated grounding connection, helping homeowners locate the correct terminal quickly for safe wiring and service. Durable, self-adhesive marking for internal appliance panels. What it does:

• Marks the chassis ground/earth connection so the grounding point is clearly visible
• Helps reduce wiring errors during service or installation
• Improves safety by making the ground terminal easy to find
• Intended for use on interior appliance sheet metal or electrical access panels

• Disconnect power before opening access panels or working near electrical components
• Clean and dry the mounting surface; peel adhesive backing and press firmly into place
• Position carefully before applying; adhesive is permanent and not intended for repeated repositioning
• Use only on appropriate interior panel surfaces away from high-heat components

This part has been discontinued by the manufacturer and is no longer available.

Replace a burned-out oven light with this 120V, 15W bulb. It restores interior illumination so you can clearly monitor cooking progress through the window, helping maintain temperature and consistent results.

• Illuminates the oven cavity during preheat, baking, and broiling
• Direct replacement for a failed or dim bulb
• Helps you check food without opening the door
• Common signs of failure: light won't turn on, flickers, or filament appears broken

• Disconnect power to the appliance and allow the oven to cool completely before servicing.
• Remove the glass lens/cover to access the bulb; handle glass carefully.
• Install using a dry cloth or gloves; do not overtighten.
• Match the bulb's voltage and wattage to the original; never exceed the rated wattage.

This spacer positions and supports internal components to maintain correct alignment and reduce wear. It helps keep panels and assemblies spaced correctly so moving parts don't rub or bind. What it does:

• Holds components at the proper distance to ensure correct fit and function
• Prevents rubbing, chafing, and premature wear between parts
• Reduces vibration and noise caused by loose or misaligned assemblies
• Can cause misalignment, excessive noise, or binding when damaged or missing

• Disconnect power and water before accessing internal parts
• Replace only with the exact spacer to maintain correct clearance and fit
• Handle small plastic/metal spacers carefully to avoid loss; keep fasteners organized

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This front side panel replaces a damaged or corroded outer side on the appliance, restoring appearance and protecting internal components from dust and wear. It provides a clean, finished surface and supports proper cabinet alignment. What it does

• Covers and protects the appliance's front side area, helping prevent dust and debris from entering internal components.
• Restores the unit's cosmetic appearance when panels are dented, scratched, or rusted.
• Helps maintain proper airflow and panel alignment for normal operation.
• Common symptoms indicating replacement: visible dents or rust, loose or warped panel edges, or gaps between cabinet pieces.

• Disconnect power to the appliance before beginning any work.
• Removal and installation typically require removing adjacent trim or fasteners; keep all screws and clips for reassembly.
• Handle the panel carefully to avoid scratching the finish; align tabs and screw holes before tightening.

This spacer positions and stabilizes nearby components to ensure proper fit and spacing during appliance assembly. It helps prevent rubbing and maintains correct panel and bracket alignment for quieter, more reliable operation. What it does:

• Keeps fixed parts correctly spaced to prevent contact and wear
• Stabilizes panels or brackets to reduce vibration and noise
• Restores proper alignment when gaps or looseness are present
• Supports fastener placement for secure reassembly

• Disconnect power and water before starting any repair
• Inspect surrounding hardware and replace any damaged fasteners before reinstalling the spacer
• Handle carefully to avoid deforming; install in original orientation and location

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.

This oven temperature probe is the internal sensor that monitors cooking cavity temperature so the oven control can regulate heat for accurate cooking and bake results. It's a direct-replacement sensing probe for compatible Bosch ovens. What it does:

• Measures internal oven temperature and sends readings to the control board
• Allows the oven to maintain set temperatures for consistent cooking
• Common symptoms of a failing probe: inaccurate oven temps, oven not reaching set temperature, or temperature-related error codes
• Works with the oven's control system to help cycle heating elements or gas valve

• Disconnect power to the appliance before servicing to avoid shock hazard
• Handle the probe and its wiring gently; avoid sharp bends or pulling on connectors
• Verify connector orientation and secure connections to the control board per OEM diagram