Parts for Gaggenau EB876-600: 01 - Cavity & Internal Top Panel Parts

This front side panel replaces a damaged or corroded outer side on the appliance, restoring appearance and protecting internal components from dust and wear. It provides a clean, finished surface and supports proper cabinet alignment. What it does

• Covers and protects the appliance's front side area, helping prevent dust and debris from entering internal components.
• Restores the unit's cosmetic appearance when panels are dented, scratched, or rusted.
• Helps maintain proper airflow and panel alignment for normal operation.
• Common symptoms indicating replacement: visible dents or rust, loose or warped panel edges, or gaps between cabinet pieces.

• Disconnect power to the appliance before beginning any work.
• Removal and installation typically require removing adjacent trim or fasteners; keep all screws and clips for reassembly.
• Handle the panel carefully to avoid scratching the finish; align tabs and screw holes before tightening.

This part has been discontinued by the manufacturer and is no longer available.

This retaining clip secures components in the espresso machine brew group to hold assemblies in place and maintain reliable brewing alignment. It's a small but essential fastener for stable operation and consistent performance. What it does:

• Secures the brew-group or internal assembly to prevent unwanted movement during operation
• Helps maintain proper seals and alignment that affect extraction and prevent leaks
• A worn or broken clip can allow parts to shift, causing noise, improper brewing, or leaks

• Unplug the machine and allow it to fully cool before servicing
• Handle small clips carefully; use appropriate pliers or tools to remove/install
• Verify proper seating and alignment of the assembly after installation

Protective cover for the temperature probe on your appliance. Replace if the cover is cracked, broken, or missing to protect the probe sensor assembly.

Replace a burned-out oven light with this 120V, 15W bulb. It restores interior illumination so you can clearly monitor cooking progress through the window, helping maintain temperature and consistent results.

• Illuminates the oven cavity during preheat, baking, and broiling
• Direct replacement for a failed or dim bulb
• Helps you check food without opening the door
• Common signs of failure: light won't turn on, flickers, or filament appears broken

• Disconnect power to the appliance and allow the oven to cool completely before servicing.
• Remove the glass lens/cover to access the bulb; handle glass carefully.
• Install using a dry cloth or gloves; do not overtighten.
• Match the bulb's voltage and wattage to the original; never exceed the rated wattage.

This listing indicates the manufacturer no longer produces or supplies this part. It is a discontinued listing; please contact our parts team to find compatible replacement options or repair alternatives for your appliance. What it does / why you might see this listing

• Marks that the original part has been discontinued by the manufacturer.
• Explains why the exact replacement is not offered for sale here.
• Helps identify when you should consider an alternate part or repair route.
• Advises against ordering unknown substitutes without verification.

• This listing is informational only and does not include a physical replacement part.

• Contact Appliance Parts Pros support with your appliance model and serial to identify current replacements or retrofit kits.
• Follow all safety precautions before inspecting or repairing appliances.

This spacer positions and stabilizes nearby components to ensure proper fit and spacing during appliance assembly. It helps prevent rubbing and maintains correct panel and bracket alignment for quieter, more reliable operation. What it does:

• Keeps fixed parts correctly spaced to prevent contact and wear
• Stabilizes panels or brackets to reduce vibration and noise
• Restores proper alignment when gaps or looseness are present
• Supports fastener placement for secure reassembly

• Disconnect power and water before starting any repair
• Inspect surrounding hardware and replace any damaged fasteners before reinstalling the spacer
• Handle carefully to avoid deforming; install in original orientation and location

Fix uneven baking or loose heating elements with this oven bake element holder. Secures the element in place for proper heat distribution. Quick repair.

Light socket for your range. Installs in the oven cavity or cooktop area to hold the interior light bulb. Replace if cracked, damaged, or no longer secure.

This part has been discontinued by the manufacturer and is no longer available.

M4 square nut for securing components in appliances. Replace if stripped, corroded, or missing to properly fasten panels and parts during assembly.

This terminal connector provides a secure electrical connection for appliance wiring, replacing a worn or damaged spade-style terminal to restore reliable power flow. It fits into the appliance's existing terminal block for a lasting repair. What it does:

• Replaces a damaged or corroded spade terminal to re-establish a solid electrical connection
• Helps eliminate intermittent power, arcing, or overheating at the wiring junction
• Works where a right-angle terminal is required to connect a wire to the appliance terminal block
• Compatible with standard insulated or non-insulated spade-style wire terminations

• Disconnect power at the circuit breaker or unplug the appliance before inspecting or replacing terminals
• Verify terminal orientation and fully seat the connector on the mating spade to ensure a tight fit
• Use proper crimping or soldering techniques if attaching bare wire; avoid loose or exposed conductors

This terminal connector provides a secure electrical connection for appliance wiring, replacing a worn or damaged spade-style terminal to restore reliable power flow. It fits into the appliance's existing terminal block for a lasting repair. What it does:

• Replaces a damaged or corroded spade terminal to re-establish a solid electrical connection
• Helps eliminate intermittent power, arcing, or overheating at the wiring junction
• Works where a right-angle terminal is required to connect a wire to the appliance terminal block
• Compatible with standard insulated or non-insulated spade-style wire terminations

• Disconnect power at the circuit breaker or unplug the appliance before inspecting or replacing terminals
• Verify terminal orientation and fully seat the connector on the mating spade to ensure a tight fit
• Use proper crimping or soldering techniques if attaching bare wire; avoid loose or exposed conductors

This convection fan motor circulates oven air to promote even heat distribution for baking and roasting. Replacing a failed motor restores airflow so your oven can maintain more consistent cooking temperatures. What it does:

• Spins the convection fan to move hot air throughout the oven cavity for more even cooking and browning
• Common symptom: uneven baking or roasting where food cooks hotter in some areas
• Common symptom: fan doesn't run, hums, or runs intermittently
• Common symptom: increased vibration or loud noise coming from the oven interior

• Disconnect power to the appliance before starting any service to avoid shock hazard
• Access usually requires removing oven panels or the rear cover; handle sharp sheet metal carefully
• Match part number and connector type before installation; secure mounting and wiring per OEM guidance

Seals the heating element opening to maintain proper heat and prevent leaks. Replace when worn or damaged to restore efficient operation. Confirm fit.

This genuine OEM replacement part is a heater ring. Also known as the heating element, the heater ring is the coil in the oven that heats up allowing the oven to do its job. Over time, through continuous wear and tear, it is possible for a heating ring to no longer heat properly and sometimes not heat at all. Luckily, replacing this part is a relatively simple process.To replace the heating element, first, make sure the oven is turned off and unplugged. After that, remove the screws of the back panel located on the interior of the oven where the fan is located. The old heater ring will be attached to a single bracket with two screws. Unfasten those screws and remove the old ring by gently pulling it out. Remove the wires attached to the back of the heating element and make sure to take note of their orientation by taking a photo. After the old heater ring has been completely removed, reattach the correct wires to the terminals of the new heating element. Secure the mounting bracket and reinstall the back panel of the oven's interior.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador ovens.

Structural angle bracket for appliance mounting and support. Replace if bent, cracked, or missing to restore proper alignment and secure installation.

This thermal protector is a temperature-sensitive cutoff designed to open a circuit at 158°F to help protect appliance motors and heating components from overheating. It provides a direct replacement for failed thermal cutoff devices. What it does:

• Opens the electrical circuit when internal temperature reaches 158°F to help prevent motor/heater overheating
• Restores normal operation when replaced if a failed protector caused a motor not to start or an appliance to shut down
• Common symptom linkage: appliance stops running, runs intermittently, or trips due to overheating
• Small, color-coded design for straightforward identification and replacement

• Always disconnect power before inspecting or replacing the thermal protector
• Verify correct orientation and secure electrical connections (crimp or solder per original wiring)
• Avoid damaging the protector or insulation; replace mounting clips or connectors if damaged

This oven temperature limiter is a safety device that prevents your oven from overheating by cutting power when temperatures exceed safe limits. It automatically resets when temperatures return to normal operating range. Replace if your oven isn't heating, shuts off unexpectedly during cooking, or won't maintain proper temperatures.

This thermal safety device automatically shuts off power to your oven when internal temperatures exceed safe limits. It acts as a backup safety system to prevent overheating and potential fire hazards. Replace this limiter if your oven won't heat at all or if it previously overheated beyond normal cooking temperatures.

This 750 ohm fixed resistor restores the correct resistance on the appliance control circuit so the control board can operate reliably. Use it to replace a burned or open resistor that interrupts normal electrical function. What it does:

• Provides a precise 750 O resistance value used in control and sensing circuits
• Limits or drops voltage to protect downstream components
• Restores stable control-board signals when the original resistor is open or damaged
• Commonly linked to symptoms like intermittent operation, control errors, or failure to start

• Disconnect power to the appliance before attempting service
• Handle the resistor and circuit board carefully to avoid damage; observe ESD precautions
• Confirm orientation and solder joint quality when installing; use proper tools and techniques

This mounting clip secures panels and small components to the appliance frame to prevent movement and vibration. It's a simple, durable replacement that restores proper fit and reduces rattling or loose trim. What it does:

• Holds trim, panels, or small assemblies in place to maintain correct alignment
• Helps stop rattling, vibration noise, and loose-fitting parts
• Restores the original fastener function after a broken or missing clip
• Fits into a designed slot or stud for a secure snap-in connection

• Disconnect power and water before starting any repair
• Remove the affected panel or trim to access the clip; gentle prying may be required
• Align clip with the factory slot or stud and press until it snaps into place
• If clip is brittle or hard to seat, replace any adjacent damaged fasteners for a secure fit

This terminal connector provides a secure electrical connection for appliance wiring, replacing a worn or damaged spade-style terminal to restore reliable power flow. It fits into the appliance's existing terminal block for a lasting repair. What it does:

• Replaces a damaged or corroded spade terminal to re-establish a solid electrical connection
• Helps eliminate intermittent power, arcing, or overheating at the wiring junction
• Works where a right-angle terminal is required to connect a wire to the appliance terminal block
• Compatible with standard insulated or non-insulated spade-style wire terminations

• Disconnect power at the circuit breaker or unplug the appliance before inspecting or replacing terminals
• Verify terminal orientation and fully seat the connector on the mating spade to ensure a tight fit
• Use proper crimping or soldering techniques if attaching bare wire; avoid loose or exposed conductors

This terminal connector provides a secure electrical connection for appliance wiring, replacing a worn or damaged spade-style terminal to restore reliable power flow. It fits into the appliance's existing terminal block for a lasting repair. What it does:

• Replaces a damaged or corroded spade terminal to re-establish a solid electrical connection
• Helps eliminate intermittent power, arcing, or overheating at the wiring junction
• Works where a right-angle terminal is required to connect a wire to the appliance terminal block
• Compatible with standard insulated or non-insulated spade-style wire terminations

• Disconnect power at the circuit breaker or unplug the appliance before inspecting or replacing terminals
• Verify terminal orientation and fully seat the connector on the mating spade to ensure a tight fit
• Use proper crimping or soldering techniques if attaching bare wire; avoid loose or exposed conductors

A replacement coil tension spring that restores proper tension and smooth movement to the appliance component it attaches to, helping return doors, levers, or assemblies to their intended position for reliable operation. What it does:

• Provides tension and return force for a door, lever, or linkage to ensure proper closing and positioning
• Helps eliminate sagging, sticking, or uneven movement caused by a worn or broken spring
• Can reduce rattling or noise from loose components when the spring is worn
• Restores normal mechanical action so other parts operate under correct load

• Disconnect power and water before servicing the appliance
• Use appropriate tools and caution—springs can be under tension and may release suddenly
• Compare the new spring to the original to ensure correct length and end configuration before installation
• If the appliance uses matching springs on both sides, replace both to maintain balanced operation

This electrical relay component controls heating elements and temperature regulation in your oven. It switches power on and off to maintain proper cooking temperatures based on thermostat signals. Replace this part if your oven won't heat up, overheats, or maintains incorrect temperatures during cooking.

This angle bracket is a metal mounting bracket used to secure internal components and maintain proper alignment. It restores stable support and helps eliminate movement or misalignment of the attached parts. What it does:

• Provides a secure mounting point to hold panels, assemblies, or components in place
• Restores proper alignment and structural support where a bent or broken bracket allowed movement
• Can stop rattling or vibrations caused by loose or damaged mounting hardware
• Used wherever a right-angle mounting support is required in the appliance assembly

• Disconnect power and any fuel lines before working on the appliance to prevent shock or injury
• Typical installation requires basic hand tools; retain original fasteners if undamaged
• Align bracket to mating hole pattern and fasten securely; do not overtighten
• If welding or drilling is required, consider service