Parts for Bosch MUZ7 ER1: 01 - Complete Parts

A replacement drive gear that restores rotational motion between the motor and driven components so the appliance can advance cycles and operate smoothly. Fits locations where the original worn or broken gear prevents proper drive engagement. What it does:

• Transfers motor rotation to the driven mechanism so parts move as intended
• Replaces worn, stripped, or broken teeth that cause slipping or no movement
• Helps stop grinding, clicking, or intermittent operation caused by damaged gearing
• Restores proper timing and engagement between motor and driven parts

• One replacement drive gear

• Disconnect power before beginning any repair
• Access may require partial disassembly; follow the appliance's service manual or diagram
• Inspect mating shafts/bushings for wear and clean before installing the new gear
• Use OEM-recommended lubricants if specified; reassemble components securely without over-tightening

This is a replacement door gasket that seals the dishwasher door to help prevent leaks and keep wash water inside the tub. Restores a tight door seal for reliable cleaning and less mess. What it does:

• Creates a watertight seal between the dishwasher door and tub to stop leaks during cycles
• Helps maintain proper wash pressure and prevents water from leaking onto the floor
• Reduces chance of detergent residue and water spotting on the floor or cabinetry
• Commonly replaced when the door leaks, water puddles near the door, or the seal is cracked or compressed

• One replacement door gasket

• Disconnect power and shut off the water supply before beginning any repair
• Follow the manufacturer's disassembly steps for removing the door inner panel or trim—handle panels gently to avoid damage
• Inspect the door cavity and mounting channel; clean and dry before installing the new gasket for best fit
• After installation, run a short test cycle and check for leaks; re-torque any fasteners to manufacturer specs if required

This stainless-steel mixing bowl is the removable work bowl for compatible stand mixers, providing a durable container for mixing ingredients and easy access for adding or removing food. Restores a secure, hygienic mixing surface. What it does:

• Holds ingredients during mixing, beating, and stirring operations
• Replaces a missing, dented, or warped bowl that prevents proper mixing
• Helps maintain food-contact hygiene with a corrosion-resistant surface
• Works with the mixer's drive and locking features to stay in place while running

• One stainless-steel mixing bowl

• Remove power from the mixer and follow the machine's manual when installing the bowl
• Align bowl with the mixer's mounting grooves or locking tabs and twist or press until it seats securely
• Inspect for damage or sharp edges before first use; do not use if bowl is cracked or severely dented
• Clean according to the mixer manual and usual stainless-steel care recommendations

This lid is the factory replacement access cover used on select Bosch appliances to restore protection and a finished appearance. It helps keep internal components covered and prevents dirt or debris from entering the compartment. What it does:

• Covers and protects the appliance compartment where internal components or controls are located
• Restores proper fit and finish to the unit's exterior after damage or wear
• Helps prevent dust, moisture, and debris from reaching internal parts that can cause issues
• Stops rattling or vibration caused by a broken or missing cover

• High-level replacement: typically unclips or is secured with screws—refer to your model's service instructions or parts diagram for exact fastening
• Disconnect power to the appliance before attempting service to avoid shock or injury
• Handle gently to avoid scratching the finish; use appropriate tools to avoid damaging mounting tabs

This driveshaft transmits motor torque to the appliance drum so the drum rotates smoothly. Replacing a worn or broken driveshaft helps stop excessive noise, wobble, scraping, or failure-to-spin symptoms. What it does:

• Transfers rotational force from the motor to the drum for normal operation
• Maintains drum alignment; a damaged shaft can cause wobbling or uneven rotation
• Failing shafts may cause loud squeaks, scraping noises, or prevent the drum from spinning
• Works with bearings, couplers and support assemblies—inspect related parts when replacing

• Disconnect power before starting work; follow all safety precautions
• Basic hand tools required; refer to the OEM diagram for disassembly steps
• Inspect and replace worn bearings, seals or couplers as needed to ensure proper operation
• If the shaft is seized or rusted, support the drum to prevent damage during removal

Color: stainless. It measures about 3-1/2 inches wide by 6 inches high.

This scraper is a simple hand tool used to remove baked-on food, sticky residue and debris from smooth appliance surfaces, making cleanup faster and helping preserve appearance when used with care and proper safety precautions. What it does:

• Removes stubborn food, grease and adhesive residue from smooth surfaces to aid cleaning.
• Helps clear debris that can interfere with surface contact or appearance.
• Allows targeted scraping in tight areas that are hard to clean with cloths or sponges.
• Reduces the need for aggressive scrubbing when used correctly.

• Always allow the appliance to fully cool before scraping.
• Hold the scraper at a low angle and use light, controlled pressure to avoid scratching.
• Wear cut-resistant gloves and eye protection when scraping.
• If working near electrical components, disconnect power before starting.

This genuine wire whisk replaces a damaged or missing mixing beater to restore whisking and light mixing performance for compatible Bosch hand mixers and stand attachments. It provides reliable aeration for batters and egg whites. What it does:

• Replaces a worn or bent wire whisk used to whip cream, beat eggs, and mix light batters
• Restores even mixing and improved aeration for better texture
• Helps eliminate uneven or slow mixing caused by damaged beaters
• Fits into the mixer's beater socket to engage with the drive for normal operation

• One replacement wire whisk (single beater)

• Always unplug the appliance before removing or installing attachments
• Remove the old beater by pressing the eject/release button or twisting per your mixer's method, then insert the replacement until it clicks or seats securely
• Test operation briefly at low speed to confirm proper engagement before full use
• Inspect for damage before each use and discontinue use if the whisk is bent or wires are loose