Parts for Bosch NKT926: 01 - Complete Parts

This small rubber gasket seals and cushions an M4 fastener to help prevent leaks and reduce vibration at attachment points. It's a compact replacement part used where a watertight or vibration-damping seal is needed. What it does:

• Creates a seal around an M4 screw or bolt to help prevent water intrusion
• Cushions fasteners to reduce vibration, noise, and metal-on-metal wear
• Restores a tightened fastener's proper sealing surface when the original gasket is worn
• Helps maintain appliance integrity around panels, brackets, or connections

• Power off and unplug the appliance before starting any repair.
• Confirm the gasket's size matches the fastener and seating area before installation.
• Install flat against the mating surface; tighten fastener snugly but avoid over-torquing which can deform the gasket.
• Handle small parts carefully and retain any removed hardware for reassembly.

This replacement case is the molded housing that protects and secures internal components, restoring structural support and helping prevent moisture, debris, or movement-related failures. It's a direct-fit exterior/interior enclosure used in the original assembly. What it does

• Protects internal components and wiring by providing a rigid enclosure
• Secures parts in their correct positions to prevent vibration and rattling
• Helps prevent water, dust, or food debris from contacting sensitive parts
• Common symptom: cracked or broken housing that allows parts to shift or causes leaks
• Common symptom: missing or damaged mounting tabs causing loose fit or vibration noise

• One replacement case

• Disconnect power and water before beginning any repair
• Handle carefully to avoid breaking fragile tabs or clips; use plastic trim tools where possible
• Transfer any gaskets, seals, or internal components from the old case exactly as originally installed
• Verify alignment of mounting points and secure all fasteners; test operation after reassembly

This rubber grommet cushions and seals a hose, wire or chassis opening to reduce vibration and help prevent abrasion or leaks. A simple, low-cost part that restores a snug, protected pass-through. What it does:

• Provides a vibration-dampening cushion where hoses or wiring pass through panels
• Creates a basic seal to help prevent chafing and moisture intrusion
• Helps reduce rattles and noise caused by loose components
• Often replaced when cracked, torn, or missing

• One grommet as described

• Inspect mating surfaces and replace if worn; press the grommet fully into the opening for a secure fit
• No special tools usually required; use gentle pressure or a non-marring tool to seat
• Disconnect power and water to the appliance before accessing internal components
• Do not use solvents or adhesives unless explicitly recommended by the manufacturer

This heat indicator body is the replacement housing that secures and protects the heat-indicator assembly while providing the visible indicator surface. Restores proper fit and appearance for the indicator on compatible appliances. What it does:

• Secures the heat indicator lens and internal indicator components in the control panel
• Protects the indicator assembly from heat, dust, and physical damage
• Restores a stable, correctly-aligned indicator when the original housing is cracked, warped, or broken
• Can resolve symptoms such as a loose, missing, or visibly damaged indicator housing that affects appearance or mounting

• One heat indicator body (housing)

• Disconnect power to the appliance before beginning any work
• Remove the control panel or access cover per the appliance service instructions to reach the indicator
• Handle the indicator lens and internal components carefully to avoid damage during replacement

This wire harness with connector routes power and signals between appliance components to restore reliable electrical connections and component communication. It replaces damaged or worn wiring that can cause intermittent operation or no power at affected circuits. What it does

• Provides a matched connectorized wiring assembly for CK 260 NKT applications to ensure correct pin-to-pin connections.
• Restores power and signal continuity to the associated control or component when the original harness is broken, frayed, or corroded.
• Helps eliminate intermittent failures, errors, or component non-response caused by loose, burned, or damaged wires.
• Maintains factory-style routing and secure connector fit to reduce strain on terminals.

• One wire harness with connector as pictured.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Verify the harness part number and connector orientation match the original before installation.
• Remove and replace carefully to avoid bending terminals; ensure connectors fully seat and locking tabs engage.