Parts for Gaggenau AH900-791: 01 - Complete Parts

This is a cylindrical sleeve used in a range vent hood assembly. It serves as a pass-through or mounting insert that helps secure components or route ducting within the hood structure. Replace this sleeve if it is cracked, deformed, or missing, which can cause loose fittings or rattling noises during hood operation.

This is a coil component used in a range vent hood. It functions as part of the electrical circuit that powers hood components. Replace this coil if your vent hood is not operating properly or if the existing coil shows signs of damage or electrical failure.

This strain relief secures the appliance power cord where it enters the cabinet, helping prevent cord pull, chafing, and accidental disconnection. It restores proper cord routing and reduces stress on internal wiring. What it does:

• Holds the power cord firmly at the entry point to stop pulling or tugging on internal connections
• Protects the cord from abrasion where it passes through the cabinet or panel
• Helps prevent intermittent power loss caused by a loose or damaged cord connection
• Fits the original cord routing to maintain safe, reliable wiring

• One strain relief clamp

• Disconnect power to the appliance before beginning any repair
• Access may require removing a rear or lower service panel; keep fasteners organized
• Replace the old clamp with the new unit, route the cord, then secure the clamp per original orientation
• Inspect the cord for damage; if the cord insulation or conductors are compromised, replace the cord

This is a mounting support clip used to secure an internal shelf or component within a range vent hood. It snaps or clips into place to hold the shelf steady and properly positioned. Replace this support if the shelf inside the hood is loose, rattling during operation, or has fallen out of alignment.

This is a replacement fluorescent lamp starter designed for use with 80W, 240V fixtures. It helps the lamp reach full brightness reliably so lighting cycles start and run normally. What it does:

• Provides the initial pulse to ignite fluorescent tubes in compatible fixtures
• Commonly restores lamps that fail to start or take multiple strikes to light
• Can stop or reduce continuous flickering or rapid flashing at startup
• Works with starter-type ballasts specified for 80W / 240V operation

• Disconnect power to the fixture before servicing to avoid shock
• Typically replaces a plug-in starter in the fixture's starter holder—pull old starter straight out and push the new starter into place
• Confirm fixture voltage and lamp wattage match the starter specifications before installing

Fluorescent light socket that connects bulb to fixture wiring. Replace if cracked, melted, or unable to hold bulb securely. Direct fit component.

This replacement light socket secures the appliance lamp and provides the electrical connection the bulb needs to illuminate the interior. It restores a loose, damaged, or non-contact lamp mount so the light works reliably. What it does:

• Holds the light bulb in place and provides the electrical contact for the lamp
• Restores a lamp that sits loosely, fails to make contact, or flickers
• Helps re-establish interior illumination when the socket is cracked, burnt, or broken
• Works with the appropriate OEM bulb and wiring to ensure correct operation

• One light socket / lamp holder (single)

• Disconnect power to the appliance before servicing to avoid shock
• Handle the bulb and socket carefully; wear gloves and eye protection as needed
• Verify correct bulb type/wattage and proper wiring connections per the appliance manual

This is a replacement tension spring for AH 250/900 assemblies. It restores proper tension in the original mechanism so moving parts operate smoothly and reliably. What it does

• Provides tension for the AH 250/900 assembly so doors/closures move and return as designed
• Replaces a stretched, broken, or weak spring that can cause sagging or improper alignment
• Helps stop rattling or uneven movement caused by a failed spring
• Restores the original fit and function of the related hinge or mechanism

• Designed to install in the original spring location; confirm orientation before removing the old spring
• Use appropriate tools and take care to avoid pinching—springs can release tension suddenly
• Disconnect power or follow appliance-specific safety steps if working near electrical components

This insulating strip (AH 250/900) is a replacement insulation piece that helps protect and separate appliance components from heat and abrasion. Restores proper clearance and helps reduce heat transfer and noise where installed. What it does:

• Provides thermal and physical separation between adjacent components to help prevent heat damage.
• Helps reduce heat transfer and localized hot spots that can affect nearby parts.
• Cushions and protects edges to reduce wear, chafing, and vibration noise.
• Common symptom: missing, torn, burned or dislodged insulation visible during inspection.

• One insulating strip (AH 250/900).

• Follow your appliance service manual for exact location and routing; replace like-for-like.
• Disconnect power (and gas if applicable) before accessing internal components.
• Use appropriate tools and wear gloves; avoid compressing the strip excessively during installation.
• If mounting surfaces are damaged or other insulation is compromised, inspect surrounding parts and replace as needed.

This insulating strip prevents unwanted heat transfer and cushions internal components to help reduce noise and wear. It restores proper thermal spacing for safe, efficient appliance operation. What it does:

• Provides thermal insulation between heat-generating parts and surrounding panels
• Cushions and separates components to reduce vibration and rubbing noise
• Helps prevent heat-related damage to wiring or nearby plastic parts
• Missing or damaged strip can cause increased cabinet heat, noise, or premature component wear

• One insulating strip

• Disconnect power and allow the appliance to cool before servicing
• Handle part carefully to avoid tearing; use appropriate tools to remove fasteners or clips
• Verify proper orientation and full seating before restoring power

Lamp window protects the internal bulb from grease and debris. Replace if cracked, discolored, or cloudy to restore proper lighting. Verify fit with your model number.

This blower control module operates the blower assembly to manage air flow and fan functions in compatible Bosch appliances, restoring proper blower response and system cycling. It's a direct-fit replacement when the blower fails to run or responds intermittently. What it does

• Supplies control signals to the blower/fan motor so the appliance can circulate air as designed
• Helps resolve symptoms such as no blower operation, intermittent blower activity, or blower not responding to controls
• Restores correct timing and sequencing of blower-related cycles when the original control board is faulty
• Works with the appliance's user controls and sensors to regulate blower behavior safely

• One blower control module (single control board)

• Disconnect power before accessing internal components to avoid shock or injury
• Replace only with the exact part number; verify orientation and connector seating during install
• Route and secure wiring harnesses to prevent pinching; avoid force when seating connectors

This PC board mount is a dedicated mounting bracket that secures the appliance control board in place, helping keep electrical connections stable and preventing damage from vibration or shifting during use. What it does:

• Secures the control (PC) board to the appliance chassis for reliable positioning
• Helps reduce board movement and vibration that can cause loose connections
• Minimizes risk of shorting from board contact with metal panels
• Needed when the board is loose, rattling, or shows visible mounting damage

• Disconnect power before starting any repair to avoid shock or damage
• Handle the control board carefully and use ESD precautions where possible
• Basic tools (screwdriver) typically required; follow OEM diagram for correct placement

This cable harness is a wiring assembly that carries electrical signals and power between components inside a range vent hood. It connects the control board, fan motor, lights, and other electrical parts. Replace this harness if the hood has intermittent electrical failures, lights that won't turn on, or a fan that stops responding to controls.

This replacement cover is an exterior access panel that protects internal dishwasher components and keeps the appliance looking finished. It restores a secure barrier over openings and helps prevent water and debris from reaching internal parts. What it does:

• Covers and protects internal components behind the lower access area.
• Helps maintain proper airflow and prevents foreign objects from entering service areas.
• Can reduce the risk of minor water exposure to internal parts when panels are missing.
• Restores the appliance's finished appearance after service or damage.

• One replacement cover panel as shown.

• Designed for user-replaceable service access; verify correct panel orientation before fastening.
• Use basic hand tools; power tools may damage trim or mounting points.
• Disconnect power and water supply to the appliance before removing panels.
• Inspect mounting clips and screws during reassembly and replace any damaged hardware.

Replacement housing cover that protects internal components and restores exterior appearance. Replaces cracked, broken, or missing covers on compatible models.

This part is a grease filter that is for range hoods. This part is responsible for filtering the grease out of the air. It helps reduce odors in the air as well.If the grease filter needs to be replaced, it may appear dirty and full of grease. If it cannot be cleaned, it can easily be replaced. This part will need to be replaced periodically over time due to normal wear and tear. This particular part includes two of the filters in the package for the ultimate convenience.This filter is compatible with range hoods that are manufactured by the Bosch brand, including Gaggenau and Thermador. It is sold individually and is sourced directly from the manufacturer.

Replacement cover for your appliance. Protects internal components from dust and debris. Order a new cover if yours is cracked, broken, or missing.