Parts for Gaggenau CK062-604: 01 - Complete Parts

This terminal connector provides a secure electrical connection for appliance wiring, replacing a worn or damaged spade-style terminal to restore reliable power flow. It fits into the appliance's existing terminal block for a lasting repair. What it does:

• Replaces a damaged or corroded spade terminal to re-establish a solid electrical connection
• Helps eliminate intermittent power, arcing, or overheating at the wiring junction
• Works where a right-angle terminal is required to connect a wire to the appliance terminal block
• Compatible with standard insulated or non-insulated spade-style wire terminations

• Disconnect power at the circuit breaker or unplug the appliance before inspecting or replacing terminals
• Verify terminal orientation and fully seat the connector on the mating spade to ensure a tight fit
• Use proper crimping or soldering techniques if attaching bare wire; avoid loose or exposed conductors

This is a rubber or silicone sealing grommet used to create an airtight seal around openings or connections within the microwave. It helps prevent moisture, heat, and air from escaping or entering where components pass through panels. Replace this part if you notice steam leaking from unusual spots, rattling noises near sealed areas, or visible cracking and deterioration of the original seal.

M4 rubber gasket creates watertight seal and reduces vibration around fasteners. Replace when worn, cracked, or leaking. Verify fit with your model number.

This is a right-side holder or endcap bracket that secures an internal component in place within the microwave. It provides structural support and proper alignment for the part it holds. Replace this holder if it is cracked, broken, or missing, which can cause the supported component to shift or rattle during operation.

This coil spring provides the tension needed for a moving assembly to return to position, restoring proper balance and motion in the appliance. It's a small replacement part that stops sagging or uneven movement. What it does:

• Re-establishes tension so doors, levers or internal mechanisms return and stay in place.
• Reduces sagging, slumping or uneven movement caused by a worn spring.
• Helps eliminate rattling or binding noises tied to a weakened spring.
• Restores smooth action for the affected hinge or linkage without replacing the full assembly.

• One replacement coil spring as shown

• Disconnect power and water before starting any repair.
• Use appropriate hand tools and keep track of fasteners; springs can be under tension—wear eye protection.
• Note original orientation and routing before removal for correct reinstallation.
• If the spring or surrounding hardware is damaged, replace associated components to ensure safe operation.

This rubber grommet cushions and secures a shaft or panel opening to reduce vibration and prevent metal-on-metal wear. It replaces a worn or missing grommet so components fit snugly and move quietly. What it does:

• Cushions and isolates vibration between parts to reduce noise and wear
• Protects wiring or shafts passing through openings from abrasion
• Helps maintain proper alignment of panels or small components
• Commonly replaced when grommets are cracked, flattened, or missing causing rattling or loose parts

• One replacement grommet

• Basic hand tools may be needed to access the mounting area; refer to your model's service instructions
• Inspect surrounding components for wear and replace any damaged clips or fasteners
• Ensure the grommet seats fully in the opening to provide proper cushion and protection
• Disconnect power before servicing electrical components to avoid shock

A replacement control knob that restores user control for range/oven cooktops. Fits the listed Bosch control shafts to provide a solid grip and clear position feedback when the original knob is cracked, loose, or missing. What it does:

• Replaces a worn, cracked, or missing control knob so you can safely set heat levels and oven functions.
• Provides a secure fit on the control shaft for reliable on/off and temperature selection.
• Restores clear tactile and visual detents for accurate setting changes.
• Helps stop slipping or spinning knobs that prevent proper control.

• Disconnect power (or turn off gas supply for gas ranges) before replacing knobs.
• Most knobs pull straight off the shaft; gently pull while wiggling if needed. Do not force.
• If a retaining screw is present, loosen it first; keep hardware for reassembly.
• If the new knob does not fit, stop and verify shaft style and part number before forcing.

Replacement energy regulator that helps control power delivery to the appliance's heating and control circuits, restoring stable performance and addressing power-related faults. Installs in-line with the factory wiring to replace a failed regulator. What it does:

• Regulates power to heating and control components to maintain expected operation.
• Can resolve symptoms such as inconsistent heating, intermittent operation, or unexpected shutdowns.
• Prevents erratic behavior caused by a failing power-control component.
• Works as a direct replacement for the factory energy regulator to restore proper function.

• Disconnect all power before beginning service to avoid shock or injury.
• Use basic hand tools; inspect wiring and connectors for damage and replace any compromised parts.
• Refer to the appliance service manual or OEM instructions for specific removal and installation steps.

Burner not heating or heating unevenly? This radiant cooktop element restores even heating on glass-top ranges. Direct replacement for failed hotplates.

Cooktop not heating? This radiant heating element restores consistent heat to your burner. Compatible with multiple cooktop models. DIY-friendly repair.

Handheld glass scraper tool for removing stubborn, baked-on residue from smooth cooktop surfaces. Replace when blade dulls or handle breaks.