Parts for Gaggenau CK074-604: 01 - Complete Parts

This is a replacement M5 x 20 gasket designed to restore a secure seal where the original small rubber gasket has failed. It prevents leaks and maintains proper pressure or fluid routing in the assembly. What it does:

• Provides a tight seal at the specified M5 x 20 connection to stop drips and seepage
• Restores proper seating for valves, fittings, or small housings that use this gasket
• Helps prevent airflow or fluid loss that can cause poor appliance performance
• Addresses common symptoms such as minor leaks, moisture buildup, or loose-fitting parts

• Replace with the appliance powered off and water/gas disconnected where applicable
• Inspect mating surfaces for damage or debris and clean before installing the new gasket
• Lubricate lightly with approved lubricant only if specified by the manufacturer

This ground wire provides a dedicated chassis ground for the appliance, restoring a safe electrical path and helping prevent shock or electrical faults. Use this exact replacement when the original grounding conductor is damaged or missing. What it does:

• Connects appliance metal chassis to earth ground to reduce risk of electrical shock
• Restores proper grounding to stop intermittent power faults or arcing at chassis-mounted components
• Helps prevent nuisance breaker trips and electrical noise that can cause control or sensor errors
• Matches OEM routing and terminal ends to fit the factory grounding point

• Disconnect power and unplug the appliance before beginning any work.
• Verify the correct grounding point and secure terminals tightly to clean metal surfaces.
• Use appropriate tools and do not alter wire ends or insulation; replace if terminals or wire are corroded.

This spring clamp is a small metal retainer clip used to secure components in place on compatible Bosch appliances, helping maintain proper alignment and stable operation. It's a direct-fit replacement when the original clip is bent or missing. What it does:

• Holds trim, panels, or small assemblies in position to prevent rattling or movement
• Restores proper fit where a damaged or lost clip causes loose parts
• Helps eliminate noise from vibrating components by maintaining secure connections
• Common symptom: loose panel edges, trim pieces, or intermittent contact from shifted parts

• Basic hand tools may be required; inspect surrounding parts for damage before installing
• Disconnect power to the appliance before working near electrical components
• Install by aligning clip over mating surfaces and compressing until it snaps into place

This strain relief secures the cooktop power cord where it enters the appliance, protecting wiring from pull damage and reducing stress on the terminal connection for safer, more reliable operation. Ideal when the cord area shows wear or looseness. What it does:

• Holds the power cord firmly at the cooktop entry to prevent tugging on internal wiring
• Reduces risk of frayed wires, loose terminals, and intermittent power caused by cord movement
• Helps maintain a stable electrical connection at the terminal block
• Commonly replaced when the cord jacket is damaged or the cord pulls freely at the entry point

• One strain relief as shown

• Disconnect electrical power at the breaker before any service; confirm power is off with a multimeter
• Access typically requires removing the cooktop/back panel to reach the terminal area
• Secure the cord under the strain relief and tighten fasteners per OEM orientation; avoid overtightening

Burner not heating or heating unevenly? This radiant cooktop element restores even heating on glass-top ranges. Direct replacement for failed hotplates.

Cooktop zone not heating or heating unevenly? This radiant surface element restores proper heat transfer to your glass ceramic cooktop. Moderate DIY repair.

This replacement hotplate is the cooktop surface element that provides direct heat for pots and pans on electric ranges. It restores a damaged, cracked, or non-heating burner so you can cook safely and consistently. What it does

• Heats cookware directly as the primary cooking surface on electric ranges
• Replaces a cracked, visibly damaged, or non-functioning surface element
• Restores consistent heat delivery when the original burner fails to warm
• Works with the range's existing control and wiring when installed correctly

• Disconnect power to the range at the breaker before servicing to avoid shock
• Remove the cooktop or access panel per your model's service instructions to access the element
• Handle the element carefully to avoid bending terminals or damaging the mounting surfaces

Handheld glass scraper tool for removing stubborn, baked-on residue from smooth cooktop surfaces. Replace when blade dulls or handle breaks.