Parts for Gaggenau KG103-8__: 01 - Complete Parts

This small rubber gasket seals and cushions an M4 fastener to help prevent leaks and reduce vibration at attachment points. It's a compact replacement part used where a watertight or vibration-damping seal is needed. What it does:

• Creates a seal around an M4 screw or bolt to help prevent water intrusion
• Cushions fasteners to reduce vibration, noise, and metal-on-metal wear
• Restores a tightened fastener's proper sealing surface when the original gasket is worn
• Helps maintain appliance integrity around panels, brackets, or connections

• Power off and unplug the appliance before starting any repair.
• Confirm the gasket's size matches the fastener and seating area before installation.
• Install flat against the mating surface; tighten fastener snugly but avoid over-torquing which can deform the gasket.
• Handle small parts carefully and retain any removed hardware for reassembly.

This thermocouple monitors the burner flame and works with the safety valve. It allows gas flow only while a flame is present and lets the valve close when no flame is detected, helping restore dependable burner operation.

• Senses burner flame heat and sends a small millivolt signal to the safety valve
• Works with the flame-failure safety system to maintain or cut gas flow based on flame presence
• Common symptoms can include: burner lights but goes out when the knob is released; needing to hold the knob down unusually long to keep the burner lit

• Disconnect power and shut off gas before servicing
• Allow the unit to cool; remove grates/caps to access the sensor tip and route the lead to the valve connection as originally installed
• Do not kink or sharply bend the lead; position the tip within the burner's flame envelope
• After reassembly, restore gas/power and test burner operation

This replacement cable with attached plug provides the appliance's mains connection, restoring safe, reliable power delivery when the original cord is damaged or worn. Use this direct-fit cord to replace frayed, cut, or nonfunctional power leads. What it does:

• Supplies AC power from the wall outlet to the appliance
• Replaces damaged or worn cords that cause intermittent power or no power
• Helps eliminate cracked insulation, exposed wires, or loose plug connections
• Restores a secure plug-to-appliance connection for normal operation

• Always unplug the appliance and shut off power at the breaker before replacing the cord
• Verify connector orientation and routing before tightening fasteners; avoid pinching the cord
• Inspect the appliance-side connector and terminal block; replace any damaged terminals

This replacement mounting bracket secures internal components and panels to restore proper fit and support. It's a small but essential hardware piece that helps stop unwanted movement and keeps parts aligned for reliable operation. What it does:

• Secures appliance panels or components to the frame to maintain correct alignment
• Prevents rattling, vibration noise, or shifting caused by a loose or broken bracket
• Restores proper support for adjacent parts that depend on a stable mount
• Helps ensure doors, panels or assemblies operate smoothly when mounting is intact

• Disconnect power and water before starting any repair
• Use basic hand tools; do not force parts — align bracket before tightening fasteners
• Follow the appliance manufacturer's service instructions for exact placement and torque
• If other fasteners or clips are damaged, replace them to ensure a secure fit

This spark electrode with attached spring is the electrode assembly used to ignite a gas burner. It provides a reliable spark and proper positioning so the burner lights consistently and safely. What it does:

• Creates the high-voltage spark that ignites the gas at the burner
• Restores ignition when a cracked, bent or worn electrode causes no spark or intermittent ignition
• Spring maintains correct electrode position and contact for consistent sparking
• Works with the stove/oven ignition system; does not include wiring harness or ignition module

• Disconnect electrical power and turn off gas supply before starting any repair
• Handle the ceramic/porcelain insulator carefully to avoid cracking
• Ensure correct electrode gap and secure mounting per the appliance's service information

This small metal spring retains a control knob on the shaft so the knob stays secure and provides proper detent action. It replaces a worn or missing knob spring to restore reliable knob feel and position. What it does

• Fits behind a control knob to hold it on the shaft and provide detent/return tension.
• Restores a loose, wobbly, or falling-off knob.
• Helps correct inconsistent knob positioning or skipped detents.
• Simple replacement that returns proper knob feel and control.

• Disconnect power to the appliance before servicing; for gas appliances also shut off the gas supply.
• Remove the knob and any escutcheon or retaining clip to access the spring; keep small parts away from children.
• Handle the spring carefully—small parts can fly when compressed; use long-nose pliers if needed.
• If knob or shaft is damaged, inspect those parts as well; this spring replaces only the retaining spring.

A white decorative ring that restores the finished look around a control or trim opening. Replaces a worn or discolored bezel to improve appearance and maintain a clean, factory look. What it does:

• Covers the gap around a control shaft or trim opening for a finished appearance
• Hides scratches, chips, or faded finish on the surrounding surface
• Keeps the control area looking factory-new after repair or part replacement
• Compatible with models that use the matching white trim ring design

• One white decorative ring

• Remove power to the appliance before accessing controls or trim areas
• Typically installs by snapping or sliding into place; check OEM instructions for exact method
• Handle gently to avoid cracking the plastic during installation
• Retain other fasteners or bezels for reassembly