Parts for Gaggenau VC355-602: 01 - Complete Parts

Replacement name plate for your appliance. Installs on the exterior to display model information. Needed when original plate is damaged, faded, or missing.

M4 rubber gasket creates watertight seal and reduces vibration around fasteners. Replace when worn, cracked, or leaking. Verify fit with your model number.

Cooktop not heating? This radiant heating element restores consistent heat to your burner. Compatible with multiple cooktop models. DIY-friendly repair.

A replacement coil tension spring that restores proper tension and smooth movement to the appliance component it attaches to, helping return doors, levers, or assemblies to their intended position for reliable operation. What it does:

• Provides tension and return force for a door, lever, or linkage to ensure proper closing and positioning
• Helps eliminate sagging, sticking, or uneven movement caused by a worn or broken spring
• Can reduce rattling or noise from loose components when the spring is worn
• Restores normal mechanical action so other parts operate under correct load

• Disconnect power and water before servicing the appliance
• Use appropriate tools and caution—springs can be under tension and may release suddenly
• Compare the new spring to the original to ensure correct length and end configuration before installation
• If the appliance uses matching springs on both sides, replace both to maintain balanced operation

This small spring fits behind the control knob to provide tension and a positive, secure feel. Replace it to restore proper knob height and a snug fit when the knob feels loose, wobbly, or won't stay seated.

• Provides spring tension between the knob and control shaft for proper engagement
• Helps keep the knob centered and at the correct height on the control panel
• Restores firm, consistent knob feel during operation
• Common symptoms: loose or wobbly knob, knob doesn't stay seated or sits unevenly

• Disconnect power; for gas appliances, also shut off the gas supply
• Pull the knob straight off the shaft; note the spring's position/orientation
• Remove the old spring and seat the new spring on the shaft or in the knob recess
• Reinstall the knob and check for smooth operation; do not force the knob onto the shaft

Replace damaged or corroded 4-wire female terminal connectors that cause appliance power issues or intermittent operation. Simple plug-in repair.

M4 square nut for securing components in appliances. Replace if stripped, corroded, or missing to properly fasten panels and parts during assembly.

This 4-wire male terminal connector provides a secure electrical connection for compatible Bosch appliances, restoring reliable power transfer to the wiring harness. Use it when the existing connector is damaged, corroded, or loose. What it does:

• Replaces a damaged or worn 4-pin male terminal to restore proper electrical contact
• Secures wiring to the appliance's harness and prevents intermittent power loss
• Helps eliminate symptoms such as burners, elements, or controls that fail to power reliably
• Meets OEM fit and form for straightforward replacement where this style connector is specified

• One 4-wire male terminal connector

• Recommended for technicians or experienced DIYers familiar with appliance electrical work
• Disconnect power at the breaker before inspecting or replacing the connector
• Verify correct wiring orientation and tightness of crimp or screw termination per service diagram
• If terminals or harness are corroded or damaged beyond the connector, replace the affected wiring or harness assembly

This strain relief secures the cooktop power cord where it enters the appliance, protecting wiring from pull damage and reducing stress on the terminal connection for safer, more reliable operation. Ideal when the cord area shows wear or looseness. What it does:

• Holds the power cord firmly at the cooktop entry to prevent tugging on internal wiring
• Reduces risk of frayed wires, loose terminals, and intermittent power caused by cord movement
• Helps maintain a stable electrical connection at the terminal block
• Commonly replaced when the cord jacket is damaged or the cord pulls freely at the entry point

• One strain relief as shown

• Disconnect electrical power at the breaker before any service; confirm power is off with a multimeter
• Access typically requires removing the cooktop/back panel to reach the terminal area
• Secure the cord under the strain relief and tighten fasteners per OEM orientation; avoid overtightening

This replacement hotplate is the cooktop surface element that provides direct heat for pots and pans on electric ranges. It restores a damaged, cracked, or non-heating burner so you can cook safely and consistently. What it does

• Heats cookware directly as the primary cooking surface on electric ranges
• Replaces a cracked, visibly damaged, or non-functioning surface element
• Restores consistent heat delivery when the original burner fails to warm
• Works with the range's existing control and wiring when installed correctly

• Disconnect power to the range at the breaker before servicing to avoid shock
• Remove the cooktop or access panel per your model's service instructions to access the element
• Handle the element carefully to avoid bending terminals or damaging the mounting surfaces

Replacement screw for your range. Secures panels, components, and trim pieces. Order a new screw if yours is stripped, missing, or damaged during repair.

Motor sleeve bearing supports rotating shaft operation. Replace if you notice excess noise, wobbling, or reduced performance. Verify fit with your model number.

This part has been discontinued and is no longer available.

Handheld glass scraper tool for removing stubborn, baked-on residue from smooth cooktop surfaces. Replace when blade dulls or handle breaks.