Parts for Gaggenau VG223-812: 01 - Complete Parts

This burner lid is the top cap for a three-piece gas cooktop burner. It protects the burner head and helps shape the flame for more even heating and stable performance during cooking. What it does:

• Covers the burner head and directs flame for consistent heat distribution
• Helps maintain stable flame pattern and reliable ignition behavior
• Replaces lids that are cracked, chipped, warped, or corroded
• Can reduce uneven cooking or flickering/unstable flames caused by damaged lids

• Turn off gas supply and power to the appliance and allow all parts to cool fully before servicing
• Remove the old lid and seat the new lid squarely on the burner head; ensure it does not obstruct the igniter or burner ports
• Inspect surrounding burner components for damage; replace any damaged rings, caps, or gaskets as needed

This burner lid is the top cover for a slim two-piece gas cooktop burner, protecting the burner head and helping direct flame. It restores proper burner appearance and helps maintain even ignition and heat distribution. What it does

• Covers the burner head to protect internal parts from spills and debris
• Helps direct gas flow for a consistent flame pattern during cooking
• Can reduce ignition issues caused by food or liquid obstruction on the burner head
• Restores the cooktop's finished look where the original lid is cracked, warped, or missing

• One burner lid (slim 2-piece style)

• Turn off the appliance and gas supply (or unplug) before servicing; allow all parts to cool completely
• Lift off the existing lid and position the replacement so it seats securely on the burner base
• Do not force or overtighten—ensure proper alignment to avoid damaging the burner head

This is a replacement M5 x 20 gasket designed to restore a secure seal where the original small rubber gasket has failed. It prevents leaks and maintains proper pressure or fluid routing in the assembly. What it does:

• Provides a tight seal at the specified M5 x 20 connection to stop drips and seepage
• Restores proper seating for valves, fittings, or small housings that use this gasket
• Helps prevent airflow or fluid loss that can cause poor appliance performance
• Addresses common symptoms such as minor leaks, moisture buildup, or loose-fitting parts

• Replace with the appliance powered off and water/gas disconnected where applicable
• Inspect mating surfaces for damage or debris and clean before installing the new gasket
• Lubricate lightly with approved lubricant only if specified by the manufacturer

This spark igniter switch mounts on the burner valve shaft and sends power to the spark module when you turn the knob, creating the clicking spark to light the burner. Replacing a worn switch restores dependable burner ignition.

• Activates the ignition circuit when the control knob is turned
• Common fix for a burner that doesn't click or spark
• Addresses intermittent sparking from a worn or contaminated switch
• Can resolve continuous clicking caused by a stuck/shorted switch after spills or moisture

• Disconnect power and shut off gas before servicing
• Remove the knob and top/panel as needed to access the valve area
• Note wire positions; transfer wires one at a time and align the switch on the valve shaft in the same orientation
• Reassemble and test burner ignition

Insulating paper provides electrical insulation in appliances. Replace if damaged, brittle, or showing signs of heat damage. Verify fit with your model number.

This terminal connector provides a secure electrical connection for appliance wiring, replacing a worn or damaged spade-style terminal to restore reliable power flow. It fits into the appliance's existing terminal block for a lasting repair. What it does:

• Replaces a damaged or corroded spade terminal to re-establish a solid electrical connection
• Helps eliminate intermittent power, arcing, or overheating at the wiring junction
• Works where a right-angle terminal is required to connect a wire to the appliance terminal block
• Compatible with standard insulated or non-insulated spade-style wire terminations

• Disconnect power at the circuit breaker or unplug the appliance before inspecting or replacing terminals
• Verify terminal orientation and fully seat the connector on the mating spade to ensure a tight fit
• Use proper crimping or soldering techniques if attaching bare wire; avoid loose or exposed conductors

Replacement control knob for gas walk-behind mowers. Restores secure grip on control stem when original is cracked, stripped, or missing. Easy install.

This bracket pin secures a door bracket to the hinge assembly so the door opens and closes smoothly. Replace a worn or bent pin to restore proper door alignment and reduce sagging or noisy operation. What it does:

• Anchors the door bracket to the hinge so the door pivots correctly
• Prevents lateral play that can cause door sag or misalignment
• Restores secure attachment when original pin is bent, worn, or broken
• Helps eliminate rubbing, binding, or uneven closing related to a loose bracket

• One bracket pin

• Disconnect power and follow all safety steps in your appliance manual before starting
• Basic hand tools are typically required; access may involve removing the door or inner panels
• Inspect surrounding bracket and hinge components; replace any damaged parts to avoid repeat failure

Engine won't stay running or shuts off unexpectedly? This gas safety shut-off solenoid controls fuel flow to prevent dangerous operation on lawn tractors.

Bottom hinge for lawn tractor hood or deck assembly. Replace if hinge is bent, cracked, rusted, or no longer secures properly. Restores proper alignment.

Snap ring secures and retains components in place on various appliances. Replace if ring is cracked, broken, or missing to restore proper assembly.

This small washer secures the thermocouple in place within the oven's gas valve assembly. Replace if the oven won't stay lit, frequently goes out during operation, or if the thermocouple appears loose or wobbly.

M4 square nut for securing components in appliances. Replace if stripped, corroded, or missing to properly fasten panels and parts during assembly.

This spark ignition module generates the electrical spark needed to light gas burners on your range or cooktop. It sends timed electrical pulses to the spark electrodes when you turn on a burner. Replace this module when burners won't light, you hear clicking but no ignition occurs, or only some burners will light properly.