Parts for Gaggenau VG352-812: 01 - Complete Parts

Replacement engine coupling for front-engine lawn tractors. Connects engine components for proper power transfer. Order new part if original is cracked or worn.

Replacement engine coupling for front-engine lawn tractors. Connects engine components for proper power transfer. Order new part if original is cracked or worn.

This VG 352 hinge secures and guides an appliance door for smooth opening and reliable closure, restoring proper alignment and operation. Designed to match the OEM fit and function for straightforward replacement. What it does

• Provides a secure pivot point so the door opens and closes smoothly
• Restores proper door alignment and helps eliminate sagging or uneven gaps
• Helps ensure the door seals correctly to improve performance
• Reduces rattling or sticking caused by worn or damaged hinges

• One VG 352 hinge (single hinge as shown)

• Basic mechanical skills and common hand tools required
• Disconnect power (and water supply for dishwashers) before servicing
• Keep track of screws and any trim; reinstall in the original orientation

Replacement gasket creates an airtight seal to prevent leaks. Replace if worn, cracked, or leaking. Verify compatibility with your model number.

This terminal connector provides a secure electrical connection for appliance wiring, replacing a worn or damaged spade-style terminal to restore reliable power flow. It fits into the appliance's existing terminal block for a lasting repair. What it does:

• Replaces a damaged or corroded spade terminal to re-establish a solid electrical connection
• Helps eliminate intermittent power, arcing, or overheating at the wiring junction
• Works where a right-angle terminal is required to connect a wire to the appliance terminal block
• Compatible with standard insulated or non-insulated spade-style wire terminations

• Disconnect power at the circuit breaker or unplug the appliance before inspecting or replacing terminals
• Verify terminal orientation and fully seat the connector on the mating spade to ensure a tight fit
• Use proper crimping or soldering techniques if attaching bare wire; avoid loose or exposed conductors

M4 rubber gasket creates watertight seal and reduces vibration around fasteners. Replace when worn, cracked, or leaking. Verify fit with your model number.

This strain relief secures the appliance power cord where it enters the cabinet, helping prevent cord pull, chafing, and accidental disconnection. It restores proper cord routing and reduces stress on internal wiring. What it does:

• Holds the power cord firmly at the entry point to stop pulling or tugging on internal connections
• Protects the cord from abrasion where it passes through the cabinet or panel
• Helps prevent intermittent power loss caused by a loose or damaged cord connection
• Fits the original cord routing to maintain safe, reliable wiring

• One strain relief clamp

• Disconnect power to the appliance before beginning any repair
• Access may require removing a rear or lower service panel; keep fasteners organized
• Replace the old clamp with the new unit, route the cord, then secure the clamp per original orientation
• Inspect the cord for damage; if the cord insulation or conductors are compromised, replace the cord

This is a replacement electrical door-latch switch that completes the circuit when the appliance door is closed, restoring normal control and operation. It replaces a failed switch to help the unit register a closed door and allow cycles to start. What it does:

• Detects/communicates door-closed status to the control so cycles can begin
• Acts as an electrical contact/signal switch for safety interlock systems
• Commonly used when the appliance won't start, stalls at door-close, or shows control/lock errors
• Restores reliable on/off/contact function for the door latch circuit

• One replacement switch as pictured and specified

• Disconnect power before accessing the door latch area; follow manufacturer safety procedures
• Verify correct part fit and orientation before final assembly
• Test switch continuity with a multimeter after removal and before final reassembly

Spring for knob that restores proper tension and return action to a control knob, helping knobs operate smoothly and stay in position. Use this small replacement when a knob feels loose, won't center, or won't return. What it does:

• Provides tension and return action for a control knob so it centers and responds correctly.
• Replaces worn or broken knob springs that cause loose, wobbly, or non-returning knobs.
• Works as the mechanical spring behind the knob's rotation and detent action.
• Small, straightforward part used wherever a control knob needs restored tension.

• Disconnect power to the appliance (unplug or switch off circuit breaker) before servicing.
• Remove the knob and any bezels per the appliance's service instructions to access the spring.
• Handle small parts carefully; keep orientation noted for correct reassembly.

This white control knob replaces a worn, faded, or damaged front-panel control on compatible cooktop or range controls to restore a secure grip and clear pointer for selecting settings. It provides a direct, intuitive interface for adjusting heat and function. What it does:

• Replaces a cracked, loose, or missing control knob so you can safely select temperatures and functions.
• Restores the visual pointer and tactile feel for precise setting changes.
• Fits onto the appliance's control shaft to transmit user input to the underlying switch or valve.
• Helps prevent accidental setting changes caused by brittle or broken knobs.

• Disconnect power (and gas, if applicable) before servicing controls to avoid injury.
• Most knobs are press-fit—pull the old knob straight off the control shaft and push the replacement fully onto the shaft.
• Verify the shaft spline type and knob orientation before ordering to ensure proper fit; special adapters or variants may be required on some models.

Snap ring secures and retains components in place on various appliances. Replace if ring is cracked, broken, or missing to restore proper assembly.

Replacement engine coupling for front-engine lawn tractors. Connects engine components for proper power transfer. Order new part if original is cracked or worn.

Replacement engine coupling for front-engine lawn tractors. Connects engine components for proper power transfer. Order new part if original is cracked or worn.

This is a replacement housing for the VG 352 assembly that restores the unit's structural support and protects internal components from damage and debris. It helps maintain proper fit and appearance after wear or impact. What it does:

• Replaces a cracked, broken, or worn outer housing to restore structural integrity
• Provides the mounting surface and alignment for internal components
• Helps reduce vibration and rattling caused by a damaged enclosure
• Protects internal parts from dirt, moisture, and accidental contact
• Addresses symptoms such as visible housing damage, loose fit, or unusual noises

• One housing (VG 352)

• Disconnect power and follow all safety precautions before starting repair
• Basic hand tools are typically required; keep track of fasteners and clips
• Inspect related seals, clips, and mounting hardware and replace if damaged

This thermocouple monitors the burner flame and works with the safety valve. It allows gas flow only while a flame is present and lets the valve close when no flame is detected, helping restore dependable burner operation.

• Senses burner flame heat and sends a small millivolt signal to the safety valve
• Works with the flame-failure safety system to maintain or cut gas flow based on flame presence
• Common symptoms can include: burner lights but goes out when the knob is released; needing to hold the knob down unusually long to keep the burner lit

• Disconnect power and shut off gas before servicing
• Allow the unit to cool; remove grates/caps to access the sensor tip and route the lead to the valve connection as originally installed
• Do not kink or sharply bend the lead; position the tip within the burner's flame envelope
• After reassembly, restore gas/power and test burner operation

M4 square nut for securing components in appliances. Replace if stripped, corroded, or missing to properly fasten panels and parts during assembly.

Replacement name plate for your appliance. Installs on the exterior to display model information. Needed when original plate is damaged, faded, or missing.

This oven grommet is a small rubber or plastic insulating component that cushions wires or protects openings. Replace when cracked, worn, or missing.

This small spring fits behind the control knob to provide tension and a positive, secure feel. Replace it to restore proper knob height and a snug fit when the knob feels loose, wobbly, or won't stay seated.

• Provides spring tension between the knob and control shaft for proper engagement
• Helps keep the knob centered and at the correct height on the control panel
• Restores firm, consistent knob feel during operation
• Common symptoms: loose or wobbly knob, knob doesn't stay seated or sits unevenly

• Disconnect power; for gas appliances, also shut off the gas supply
• Pull the knob straight off the shaft; note the spring's position/orientation
• Remove the old spring and seat the new spring on the shaft or in the knob recess
• Reinstall the knob and check for smooth operation; do not force the knob onto the shaft