Parts for Gaggenau VR322-612: 01 - Complete Parts

This terminal connector provides a secure electrical connection for appliance wiring, replacing a worn or damaged spade-style terminal to restore reliable power flow. It fits into the appliance's existing terminal block for a lasting repair. What it does:

• Replaces a damaged or corroded spade terminal to re-establish a solid electrical connection
• Helps eliminate intermittent power, arcing, or overheating at the wiring junction
• Works where a right-angle terminal is required to connect a wire to the appliance terminal block
• Compatible with standard insulated or non-insulated spade-style wire terminations

• Disconnect power at the circuit breaker or unplug the appliance before inspecting or replacing terminals
• Verify terminal orientation and fully seat the connector on the mating spade to ensure a tight fit
• Use proper crimping or soldering techniques if attaching bare wire; avoid loose or exposed conductors

M4 rubber gasket creates watertight seal and reduces vibration around fasteners. Replace when worn, cracked, or leaking. Verify fit with your model number.

This rubber grommet cushions and secures a shaft or panel opening to reduce vibration and prevent metal-on-metal wear. It replaces a worn or missing grommet so components fit snugly and move quietly. What it does:

• Cushions and isolates vibration between parts to reduce noise and wear
• Protects wiring or shafts passing through openings from abrasion
• Helps maintain proper alignment of panels or small components
• Commonly replaced when grommets are cracked, flattened, or missing causing rattling or loose parts

• One replacement grommet

• Basic hand tools may be needed to access the mounting area; refer to your model's service instructions
• Inspect surrounding components for wear and replace any damaged clips or fasteners
• Ensure the grommet seats fully in the opening to provide proper cushion and protection
• Disconnect power before servicing electrical components to avoid shock

Catches grease and food drips under the broiler cavity to keep your oven clean and reduce smoke. Replace when warped, rusted, or heavily stained.

This is a protective cover panel for the microwave's main housing assembly. It shields internal components from dust, moisture, and damage while maintaining the structural integrity of the unit. Replace this cover if it is cracked, warped, or missing, which can expose internal parts and affect safe operation.

Headless screw (M3 x 4mm) for securing internal components in appliances. Replace if missing, stripped, or damaged during repairs or maintenance.

This terminal connector provides a secure electrical connection for appliance wiring, replacing a worn or damaged spade-style terminal to restore reliable power flow. It fits into the appliance's existing terminal block for a lasting repair. What it does:

• Replaces a damaged or corroded spade terminal to re-establish a solid electrical connection
• Helps eliminate intermittent power, arcing, or overheating at the wiring junction
• Works where a right-angle terminal is required to connect a wire to the appliance terminal block
• Compatible with standard insulated or non-insulated spade-style wire terminations

• Disconnect power at the circuit breaker or unplug the appliance before inspecting or replacing terminals
• Verify terminal orientation and fully seat the connector on the mating spade to ensure a tight fit
• Use proper crimping or soldering techniques if attaching bare wire; avoid loose or exposed conductors

This small component fits into or behind the control dial on the microwave's front panel. Replace it if the control knob feels loose, doesn't turn properly, or if timing/power selections become inaccurate.

Replacement griddle brush lifts grease and food residue from cooking surfaces. Replace when bristles wear or flatten. Verify fit with your model number.

This 1700W, 230V replacement heating element restores oven/grill heating for consistent broil and bake performance. It fits into the grill/broil cavity to provide direct radiant heat where the original element has failed. What it does:

• Heats the grill/broil area to allow proper browning and searing
• Replaces a burned-out or open element that prevents the oven from reaching broil temperature
• Helps eliminate uneven cooking caused by a partially failed element
• Works with standard oven control to cycle power on and off as directed

• One 1700W, 230V heating element

• Disconnect power at the breaker or unplug the appliance before starting any work
• Handle the element carefully; avoid bending the tubed heating element or touching terminals with bare hands
• Verify electrical connections are tight and correctly routed before restoring power

This VG 352 hinge secures and guides an appliance door for smooth opening and reliable closure, restoring proper alignment and operation. Designed to match the OEM fit and function for straightforward replacement. What it does

• Provides a secure pivot point so the door opens and closes smoothly
• Restores proper door alignment and helps eliminate sagging or uneven gaps
• Helps ensure the door seals correctly to improve performance
• Reduces rattling or sticking caused by worn or damaged hinges

• One VG 352 hinge (single hinge as shown)

• Basic mechanical skills and common hand tools required
• Disconnect power (and water supply for dishwashers) before servicing
• Keep track of screws and any trim; reinstall in the original orientation

Appliance overheating or shutting off unexpectedly? This 253°F thermal protector prevents damage by cutting power when temperatures exceed safe limits.

M4 square nut for securing components in appliances. Replace if stripped, corroded, or missing to properly fasten panels and parts during assembly.

Replacement name plate for your appliance. Installs on the exterior to display model information. Needed when original plate is damaged, faded, or missing.

This is a slide rail that supports and guides a drawer in and out of a range or oven. It mounts inside the cavity where the storage or warming drawer sits, allowing smooth opening and closing. Replace this part if the drawer sticks, wobbles, does not glide smoothly, or falls off its track.

This small spring fits behind the control knob to provide tension and a positive, secure feel. Replace it to restore proper knob height and a snug fit when the knob feels loose, wobbly, or won't stay seated.

• Provides spring tension between the knob and control shaft for proper engagement
• Helps keep the knob centered and at the correct height on the control panel
• Restores firm, consistent knob feel during operation
• Common symptoms: loose or wobbly knob, knob doesn't stay seated or sits unevenly

• Disconnect power; for gas appliances, also shut off the gas supply
• Pull the knob straight off the shaft; note the spring's position/orientation
• Remove the old spring and seat the new spring on the shaft or in the knob recess
• Reinstall the knob and check for smooth operation; do not force the knob onto the shaft

Replacement screw for your range. Secures panels, components, and trim pieces. Order a new screw if yours is stripped, missing, or damaged during repair.