Parts for Ge ZGG48L30CSS: 01 - Gas Grill Parts

This is a venturi gasket that serves as a replacement for use with gas ranges. The gasket is used on the venturi tubes, which extend from the burner to the control valves. The gaskets provide a seal, so there is not too much air mixing with the gas. If they are not working properly, they could also let the gas out beneath the burner, which would be dangerous.Over time, the gasket material will start to wear down, break, and crumble and will need to be replaced. Additionally, when doing other work, such as installing a new head on the range, it is advisable to change out the gasket at the same time if it appears worn. The replacement for this part is relatively simple.This venturi gasket will work with many models of gas stoves from General Electric. The gasket is a genuine OEM replacement part that has been sourced directly from the manufacturer. The gasket is sold individually. Owners might want to have a couple of replacements on hand.

This right-hand side body panel restores the cabinet exterior and protects internal components from damage. It provides a clean finished look and replaces dented, scratched, or missing side trim on compatible refrigerators. What it does:

• Covers and protects the refrigerator's right exterior side from impacts and wear
• Restores a uniform exterior appearance after collision or corrosion damage
• Helps keep internal insulation and components enclosed and secure
• Prevents exposure of wiring and internal chassis parts

• Disconnect power and empty nearby shelves or contents before starting work
• Installation typically requires removing trim screws and lifting the panel into place—use basic hand tools
• Keep original fasteners and for correct panel alignment and screw locations

This left side body panel replaces a damaged or missing exterior side piece to restore your appliance's structural support and appearance. It provides a clean, factory-fit surface so the cabinet sits and looks correct. What it does:

• Covers and protects the appliance's left exterior side from dents, scratches, and moisture exposure
• Restores proper cabinet alignment and helps keep internal components enclosed
• Improves appliance appearance by replacing a corroded or cosmetically damaged panel
• Stops drafts or gaps that can form when a side panel is bent or loose

• One left side body panel

• Unplug the appliance or disconnect power before starting work
• Remove adjacent panels, trim, or mounting screws as needed to access panel fasteners
• Handle carefully to avoid sharp edges; two people may be needed to align and secure the panel
• Reinstall screws and trim to factory torque; test for secure fit and proper cabinet alignment

This rotis burner housing replaces the worn or damaged housing that supports and aligns the burner on your range, restoring stable burner placement and proper burner cap seating for safer cooking. What it does:

• Secures the burner assembly and positions the burner head and cap
• Helps maintain an even flame by keeping burner parts aligned
• Addresses symptoms like burner caps that wobble, uneven flames, or improper burner seating
• Prevents contact between burner components and the cooktop while in use

• Turn off gas supply and disconnect power before servicing gas ranges
• Remove grates and burner caps, then lift out the cooktop or control panel as needed to access the housing
• Inspect surrounding gaskets and seals; replace if brittle or damaged

This grill cover handle is used to open and close a grill. If the handle is missing, opening the grill can be difficult and dangerous. Over time, heat from the grill can cause the handle to become cracked or break and fall off. When this happens, the handle should be replaced before using the grill. It is not advised to use a makeshift handle or open the grill with anything other than an OEM handle. Open the grill cover and look underneath to locate the screws for the handle. Remove the broken handle using a screwdriver. Save the screws for installing the new handle. Remove the handle from the packaging and line it up with the predrilled holes on the grill. Make sure the holes align. Install the screws from the backside of the lid and tighten. Close the grill. This grill cover handle is made of durable plastic and is sold individually. It does not come with installation screws. It is designed for use in grills manufactured by General Electric.

This right-side anti-flip bracket helps secure the appliance door/assembly to prevent tipping or unexpected movement, restoring stable operation and safer use. Fits the original mounting points for a direct replacement. What it does:

• Anchors the appliance door/assembly to reduce upward or forward flipping during use
• Helps stabilize a door that tilts, binds, or does not stay seated when opening/closing
• Restores correct alignment between the door and cabinet/frame for smoother operation
• Works with factory mounting hardware and original bracket locations

• One right-side anti-flip bracket

• Follow the appliance manufacturer's service manual for disassembly and reassembly steps
• Use appropriate hand tools; keep track of screws and any removed trim pieces
• Disconnect power (and gas if applicable) before beginning work to avoid electrical or gas hazards

This single grill rack replaces a worn or damaged 36" monogram-style grill rack to restore proper food support and even broiling. It installs in the grill cavity to hold cookware or food during high-heat cooking. What it does:

• Provides a sturdy surface for grilling and broiling inside the oven or grill cavity
• Allows hot air to circulate around food for more even cooking
• Replaces racks that are bent, warped, or rusted and no longer hold cookware securely
• Helps prevent food from slipping into the burner area or onto the grill floor

• One 36" single grill rack

• Allow the appliance to cool and disconnect power before replacing the rack
• Slide the rack into the existing support slots; no special tools normally required
• Inspect support rails for damage and ensure the rack seats evenly to avoid tipping
• Follow all safety instructions in your appliance owner's manual

Replacement H-shaped surface gas burner for select GE ranges that restores proper flame distribution and cooking performance on the cooktop. Replaces damaged or warped H burners to help ensure even heating. What it does:

• Delivers gas to the H-shaped surface burner position to produce stable cooking flames.
• Restores even heat when a worn or damaged burner causes uneven cooking or low flame.
• Helps address symptoms like flickering or lifting flames, visible warping, cracks, or heavy corrosion.
• Serves as the direct replacement component for the H-style burner assembly on compatible gas cooktops.

• Turn off the gas supply and disconnect power to the appliance before beginning any work.
• Remove grates and burner caps to access the burner; handle parts carefully to avoid damage.
• After installation, check for steady ignition and test for gas leaks with a soapy-water solution—do not use an open flame.

This is a GE radiant heating element. This radiant heating element is designed to be installed in several models of GE gas grills. The radiant heating element is the source of heat for the range portion of the grill. The assembly consists of the grill grate, the heating element, and the reflecting pan, which adds another heat level to optimize cooking. When this heating element goes out, the griddle/range portion of the grill will no longer operate efficiently. This loss of power may take place over a long period or happen all at once. Inspect the component for any debris or grease buildup when malfunctions take place. Buildup from food by products could cause the element not to operate correctly.Before beginning any repairs or installations, always disconnect the grill from any gas sources. Use gloves to avoid accidental cuts or scrapes from handling the sharp edges of the grill grate and reflection pan. Remove the old unit by disconnecting it from the gas line to access the main tank. The heating element can be accessed by lifting the grill grate. The element is directly beneath the grate, which can also be easily removed. This is a genuine OEM product and is sourced directly from the manufacturer. This product is designed exclusively for GE products.

This heat shield protects the oven cavity and surrounding components from excessive heat, helping prevent damage and maintain safe operation. It fits where the original shield has become warped, corroded, or missing. What it does:

• Redirects and absorbs oven heat to protect nearby wiring, insulation, and cabinet panels
• Helps maintain proper internal temperature distribution for safer, more reliable operation
• Prevents heat-related damage that can cause discoloration, melting, or premature component failure
• Commonly replaced when the shield is dented, rusted, or loose and no longer secures correctly

• Disconnect power (and gas if applicable) before beginning any repair
• Wear work gloves and eye protection; edges may be sharp
• Compare the new shield to the original for correct orientation and mounting hole alignment