Parts for Gaggenau EB985-610: 02 - Cavity Parts

The Bulb is an OEM part for Bosch ovens. This component provides illumination inside the oven, allowing you to easily monitor the cooking process without opening the door and losing heat.

Causes of a bad bulb can include filament burnout due to extended use, electrical issues that cause power surges, or physical damage from accidental impacts. 

Symptoms of a bad bulb include:

• The oven light not turning on
• Flickering light inside the oven
• Dim or uneven lighting
• The bulb appearing visibly damaged or burnt out

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This convection ring element heats the oven cavity for convection cooking, restoring even baking and broiling performance when the original element has failed. It replaces the circular heating element used with the fan-forced cooking system. What it does:

• Heats the oven cavity so heated air circulates for consistent baking and roasting
• Restores convection cooking performance when the ring element is burnt out or intermittent
• Can reduce uneven browning or undercooked spots caused by a failing element
• Works with the oven's fan and controls to maintain set temperatures during convection cycles

• 1 convection ring element

• Disconnect power to the range at the breaker before attempting any service
• Replace only after interior panels and fan access covers are removed per the service manual
• Handle the element carefully to avoid bending or damaging terminals; secure mounting hardware as found

This gasket seals the heating element opening to help maintain proper heat and prevent leaks or debris entry. It restores a tight fit between the element and the appliance cavity for safer, more efficient operation. What it does:

• Creates a heat-resistant seal around the heating element to reduce heat loss
• Helps prevent dust, grease, and moisture from entering the element cavity
• Reduces risk of shorting or arcing caused by gaps or damaged insulation
• Common symptom fix: frayed, cracked, or missing gasket around element flange

• One heating element gasket

• Disconnect power (or unplug) and allow the appliance to fully cool before servicing
• Access the element per your model's service instructions; remove element mounting hardware to replace gasket if required
• Inspect element flange and mounting surface; replace gasket only if it matches OEM shape and seating
• If you see corrosion, burning, or element damage, replace the element as needed and retest after installation

This control panel lens cover protects the oven's display and touchpad area from spills, scratches and everyday wear while keeping the display visible and looking finished. It restores the appliance's appearance and helps prevent damage to the underlying controls. What it does

• Shields the display and control buttons from food splatter, grease and scratches.
• Keeps the display readable by reducing direct contact and surface damage.
• Replaces cracked, chipped or yellowed lens surfaces that obscure the control panel.
• Helps prevent moisture from directly contacting the control electronics when properly seated.

• One lens cover for the control panel.

• Disconnect power to the appliance before starting any work.
• Typically installs by removing the control panel trim or bezel; handle the lens by the edges to avoid fingerprints.
• Inspect mounting tabs or clips for damage and align carefully before snapping or fastening into place.
• If screws or additional trim are required, reuse OEM fasteners.

A flexible replacement gasket that seals and side lamp glass, cushioning and securing the glass to help block moisture and debris from the lamp housing. Restores a tighter fit and reduces vibration or rattling around the lamp area. What it does:

• Seals the edge of the lamp glass to keep moisture, dust and food debris out of the lamp housing.
• Cushions and centers the lamp glass to reduce vibration and prevent rattling or glass movement.
• Helps maintain a stable lamp assembly so the light cover sits flush and stays in place.
• Use when the gasket is cracked, torn, deformed or missing, or when the lamp glass feels loose.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Handle lamp glass carefully to avoid breakage; wear gloves and eye protection as needed.
• Seat the gasket evenly around the lamp glass edge and press into the channel until fully seated; avoid stretching or deforming the seal.
• Replace only with the exact OEM part number to ensure correct fit and sealing.

This spacer positions and stabilizes nearby components to ensure proper fit and spacing during appliance assembly. It helps prevent rubbing and maintains correct panel and bracket alignment for quieter, more reliable operation. What it does:

• Keeps fixed parts correctly spaced to prevent contact and wear
• Stabilizes panels or brackets to reduce vibration and noise
• Restores proper alignment when gaps or looseness are present
• Supports fastener placement for secure reassembly

• Disconnect power and water before starting any repair
• Inspect surrounding hardware and replace any damaged fasteners before reinstalling the spacer
• Handle carefully to avoid deforming; install in original orientation and location

This locking clip secures a small cap or cover in place, restoring a snug fit and preventing the cap from coming loose during use. It's a simple replacement that helps keep trim and small assemblies aligned. What it does

• Secures a cap or cover to the appliance frame so the cap stays in position
• Prevents rattling, loss of the cap, and related cosmetic gaps
• Restores correct alignment of trim or small access covers after damage or wear
• Small, clip-style fastener designed for a snap-in fit where applicable

• One locking clip

• Disconnect power to the appliance before attempting service
• Typically installs by snapping into place; may require a flat screwdriver or small pry tool to remove the old clip
• Handle small parts carefully to avoid loss; keep track of any screws or retainers removed

This Halogen Bulb is an OEM part for Bosch Ranges. It provides illumination for the range's interior. Continuous use or high temperatures can cause the bulb to burn out or fail.

What Causes a Bad Halogen Bulb: 
Repeated heating and cooling cycles, along with continuous use, can cause the halogen bulb to burn out or break.

Symptoms of a Bad Halogen Bulb:

• The bulb is not lighting up
• Visible signs of damage or a broken filament
• Flickering or intermittent lighting

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This halogen bulb socket connects and secures the oven light bulb so the interior light works reliably when the door is opened or the light switch is used. Replaces a worn or damaged socket to restore a solid electrical connection. What it does:

• Holds the halogen oven light bulb in place and provides the electrical contacts to power the lamp
• Commonly used when the oven light flickers, won't turn on, or the bulb becomes loose
• Maintains correct alignment and insulation for safe bulb operation
• Designed for direct replacement of the original socket in compatible ovens

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Allow the oven and bulb to cool completely before touching components
• Handle halogen bulbs with a clean cloth or gloves; oils from skin can shorten bulb life

This door lock assembly secures the dishwasher door and completes the start/operation circuit so the machine can run. Replacing a failed latch restores proper door closure and reliable wash-cycle starts. What it does:

• Mechanically latches the dishwasher door and holds it closed during operation
• Completes the electrical door-closed switch so the control will start and run cycles
• Commonly replaces locks that prevent the dishwasher from starting, show an unlocked error, or fail to stay latched
• Helps stop leaks and interruptions caused by a door that won't seal or lock

• One door lock assembly

• Disconnect power and water supply before starting work
• Access typically from the front: remove the door inner panel or control panel as needed
• Handle trim and mounting screws carefully; keep small fasteners and gaskets together
• After installation, verify the door latches securely and the dishwasher starts a test cycle