Parts for Gaggenau VG231-211CA: 02 - Component Assemblies & Fascia Panel Parts

M4 rubber gasket creates watertight seal and reduces vibration around fasteners. Replace when worn, cracked, or leaking. Verify fit with your model number.

This is a factory-style orifice set for natural gas appliances that meters fuel to the burner ports for a stable, correct flame. Replacing worn or incorrect orifices helps restore even burner performance and safe combustion. What it does:

• Controls gas flow to burner ports so flames burn at the proper size and shape
• Supports consistent ignition and steady burning across burners
• Can resolve symptoms like weak or uneven flames, delayed ignition, or burners that won't reach expected heat
• Designed for use where a 15 mbar natural gas pressure specification is required

• One complete orifice set

• Turn off gas supply and power before servicing; follow all local codes
• Install only when confirmed as the correct orifice set for your appliance and gas type
• Tighten fittings to OEM torque; inspect connections and test for leaks after installation

These nozzles control the flow and mixture of liquid propane gas to each range burner for proper combustion. Located inside each burner assembly on gas ranges, replace them if burners won't light, produce uneven flames, or when converting between different gas types.

This replacement burner tube routes gas to the cooktop burner for correct flame delivery and stable cooking performance. It restores proper gas flow to a single burner when the original tube is damaged or deteriorated. What it does

• Directs gas from the manifold to the burner ports for ignition and steady flame.
• Can resolve weak, irregular, or missing flames at one burner.
• Helps stop flame lifting or poor heat distribution caused by a warped or damaged tube.
• Supports safe ignition when paired with a properly functioning igniter and burner cap.

• Turn off gas supply and electrical power to the appliance before starting work.
• Use proper fittings and seals; inspect nearby gaskets and mounting hardware and replace if damaged.
• After installation, check all connections for leaks with a non-corrosive leak detector or soapy water; do not use open flame.

This is a replacement nut for the VG 230 assembly, used to secure the associated hardware on compatible Bosch appliances. Installing the correct nut restores safe fastening and helps stop looseness, rattles, or misalignment. What it does:

• Secures the VG 230 component or bracket to its mounting point
• Keeps threaded connections tight under vibration and normal use
• Helps prevent intermittent contact, rattling, or movement of the assembly
• Restores proper mechanical alignment after a stripped or missing fastener

• Disconnect power and water (if applicable) before servicing the appliance.
• Use the correct size wrench or socket to avoid rounding the nut.
• Replace with the exact OEM part to maintain fit and function; do not overtighten.

This rubber door seal forms a watertight barrier around the dishwasher door to help prevent leaks and keep water contained during cycles. Replaces worn or damaged seals to restore proper sealing and reduce drip and pooling near the door. What it does:

• Creates a continuous water seal around the dishwasher door to prevent leaks during wash cycles
• Keeps water and spray inside the tub for efficient cleaning
• Helps reduce moisture and residue buildup at the door edge
• Commonly replaced when you see visible cracks, flattening, or leaking at the door

• One replacement door sealing gasket

• Simple gasket replacement; remove the old seal from the door channel and press the new seal into place, working around the full perimeter
• Make sure the seal sits fully into the door channel and the ends align without gaps
• Disconnect power and water supply before starting work and follow manufacturer instructions

This is a sealing component designed to fit around the gas valve area of a range or oven. It prevents gas and heat from escaping at the valve connection point, ensuring a safe and proper seal. Replace this seal if you notice gas odors near the valve, signs of heat damage around the connection, or if the old seal has become brittle or cracked.

Replace your worn or damaged cooktop fascia panel. This decorative trim piece frames the cooking surface and provides a finished look. Ideal for cracked or discolored panels.

A small support bracket that secures the mounting strip and helps hold appliance panels and components in proper alignment for reliable operation. Replaces a worn or damaged bracket to reduce rattling and improve fit. What it does

• Supports and secures the mounting strip that attaches panels or trim to the appliance
• Keeps panels, trim, or adjacent components aligned and stable
• Helps prevent movement, vibration noise, or gaps caused by a loose or broken bracket
• Commonly replaced when the bracket is cracked, bent, or missing

• One mounting strip bracket

• Disconnect power (and water, if applicable) before servicing the appliance
• Use appropriate hand tools; mounting screws or clips may be required
• Handle panels and sharp sheet metal carefully to avoid cuts or damage
• Follow the OEM service manual or instructions for exact removal and reassembly steps

This spark module generates the electrical spark needed to ignite gas burners on your range. It sends timed electrical pulses to the spark electrodes when you turn on a burner. Replace this part if your gas burners won't light, clicking sounds are continuous, or there's no spark when turning burner knobs.

Fix loose or burnt electrical connections with this terminal connector. Essential for restoring power flow in appliances. Simple repair requiring basic tools.

This is a replacement pressure regulator (VG 232) that restores steady system pressure so the appliance runs reliably and parts operate as designed. Fits as a direct replacement where the VG 232 regulator is specified. What it does

• Regulates and stabilizes system pressure to maintain consistent performance
• Prevents pressure-related issues that can cause inconsistent operation or trigger error conditions
• Helps reduce stress on downstream components by controlling pressure spikes
• Restores normal operation when a failed regulator is causing performance problems

• One pressure regulator (VG 232)

• Disconnect power and shut off the relevant supply (water or gas) before starting work
• Handle the part carefully and use appropriate tools; follow the appliance manufacturer's service instructions
• Inspect seals and fittings during replacement; replace any worn seals to prevent leaks