Parts for Electrolux GCFE307CBFA: 03 - Body Parts

Secures internal components to the range cabinet or chassis. Replace this mounting bracket if the original is cracked, broken, or missing to restore alignment.

This replacement cover protects internal components and restores your appliance's finished appearance. It fits the factory location to keep parts shielded from debris and accidental contact. What it does

• Replaces a cracked, broken or missing cover to stop exposed components and reduce risk of damage
• Helps prevent debris and moisture from entering internal areas that can cause malfunctions
• Eliminates rattles or vibration caused by a loose or damaged housing piece
• Restores a clean, finished look to the appliance exterior

• Disconnect power to the appliance before starting any repair
• Basic hand tools such as a screwdriver may be required; keep fasteners from the original part for reuse if in good condition
• Handle part carefully to avoid scratching the finished surface during installation

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

Flat wire oven rack that sits on interior supports to hold cookware at the correct height. Replace your bent, rusted, or missing rack to restore stability.

Outer trim cover that protects internal components and provides a finished look. Replace if cracked, broken, or missing to restore appearance and shield parts.

Replace your gas range door seal when you notice heat escaping or uneven cooking. This gasket creates an airtight seal around the oven door. Verify fit with your model number before ordering.

Replace your range's interior light assembly to restore oven cavity illumination. Install when bulb won't stay secure or socket is damaged. Verify fit with your model number.

Oven not heating to the right temperature? Replace the temperature sensor probe to restore accurate heat regulation and consistent baking results.

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

This oven bake element heats the interior of an electric oven for baking and roasting, restoring proper cooking temperatures and even heat distribution when the original element fails. What it does:

• Heats the oven cavity to produce consistent bake and roast temperatures.
• Replaces a cracked, burned, or nonfunctional bake element.
• Helps resolve symptoms such as oven not reaching set temperature, uneven baking, or visible element damage.
• Works with the oven's temperature controls and broil/bake circuits as the primary lower heating element.

• Disconnect power to the appliance at the breaker or unplug before attempting installation.
• Handle the element carefully to avoid bending or damaging the terminals and mounting flange.
• Verify fit and terminal type match your oven before finalizing installation.

If your oven won't heat or heats unevenly, the heating element may be faulty. This bake or broil element restores proper oven temperature. DIY-friendly repair.

Replacement door hinge for gas ranges. Installs on the oven door to allow smooth opening and closing. Replace if cracked, broken, or door sags.

Mounting bracket secures internal range components. Replaces cracked, damaged, or missing brackets to restore proper alignment and eliminate rattling.

Pin component for electric and gas ranges. Installs in assembly connections. Replace if broken, bent, missing, or worn to restore proper fit and alignment.

This replacement evaporator fan blade helps circulate cold air inside the freezer or refrigerator compartment to maintain even temperatures and proper cooling performance. A direct-fit replacement when the existing blade is cracked, warped, or missing. What it does:

• Moves air across the evaporator to promote even cooling and frost prevention
• Restores proper airflow when a damaged blade causes noise or reduced cooling
• Helps reduce hot or warm spots inside the compartment
• Quiet, balanced operation when installed correctly

• One replacement evaporator fan blade

• Disconnect power to the appliance before starting any repair
• Typically accessed by removing interior panels in the freezer/refrigerator compartment
• Inspect the fan motor shaft and mounting for damage before installing the new blade

Anti-tip bracket kit secures freestanding or slide-in ranges to prevent forward tipping. Includes mounting hardware for floor or wall installation.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.