Parts for Electrolux FFUE2024ANE: 03 - Cabinet Parts

Replacement access panel cover for freezers and refrigerators. Restores finished appearance and protects internal components. Replaces cracked or missing panels.

Hardware screw for securing shelves, bins, and trim panels inside refrigerators and freezers. Replace when stripped, corroded, or missing during repairs.

This is a gray plastic cover that conceals the hinge mounting hole on the non-hinged side of the refrigerator or freezer door. It provides a clean, finished appearance where a reversible door hinge is not installed. Replace this cover if it is cracked, missing, or discolored, leaving an exposed hole in the cabinet or door.

This is a gray plastic cover that fits over the lower door hinge on a freezer, concealing the hinge hardware for a clean finished appearance. It snaps into place over the hinge area near the base of the unit. Replace this cover if it is cracked, broken, or missing, which can leave the hinge exposed and detract from the appliance's appearance.

The Air Tower is an OEM part for Frigidaire refrigerators. The cover helps circulate cold air throughout the freezer while also protecting internal components from damage or debris.

Over time, freezer air tower covers can become damaged or discolored due to repeated exposure to cold temperatures and humidity inside the freezer. Signs of a bad cover include cracks, holes, or missing pieces that compromise its ability to properly ventilate the freezer.

Symptoms of a bad freezer air tower cover include:

• Inefficient air circulation leading to warmer freezer temperatures
• Formation of ice buildup around the evaporator coil
• Exposure of internal freezer components to damage or contamination

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic

LED light bulb illuminates refrigerator and freezer compartments for easy food visibility. Replace when dim or burned out. Verify fit with your model.

Light socket holds and connects the bulb in your refrigerator. Replace if lights flicker or won't turn on. Verify fit with your model number.

This assembly includes a defrost bi-metal thermostat and the accompanying wire harness for a freezer. The thermostat monitors evaporator coil temperature and signals the defrost system to turn on or off, preventing excessive frost buildup. Replace this assembly if the freezer is accumulating heavy frost on the back wall, running too warm, or if the defrost cycle is not activating properly.

The Fan Mount is an OEM part for Frigidaire refrigerators. It is responsible for holding the evaporator fan in place within the refrigerator's freezer compartment.

A bad fan mount can be caused by regular wear and tear, physical damage, or improper installation. Signs of a faulty fan mount include excessive noise coming from the freezer, reduced cooling performance, or the fan not spinning properly.

Symptoms of a bad fan mount can include:

• Unusual noises coming from the freezer
• Insufficient cooling or uneven temperature
• The evaporator fan not spinning
• Excessive frost or ice buildup in the freezer

Replace your damaged or worn-out fan mount with this genuine OEM part to ensure proper airflow in your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Bottom Hinge is an OEM part for Frigidaire freezers. It is responsible for supporting and allowing the smooth opening and closing of the freezer door.

A bad freezer bottom hinge can be caused by wear and tear, damage, or improper installation. When the bottom hinge becomes faulty, it can result in issues such as difficulty in opening or closing the freezer door, misalignment, or improper sealing.

Symptoms of a bad freezer bottom hinge include:

• The freezer door not closing properly or popping open
• Uneven or misaligned door alignment
• Excessive gaps or air leaks around the door seal
• Unusual noises when opening or closing the door

Replace your faulty freezer bottom hinge with this genuine OEM Frigidaire part to restore  your freezer door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Bottom door hinge supports and aligns your freezer door for smooth operation and proper sealing. Replace if door sags or won't close flush. Verify fit.

This is the cover assembly that mounts over the evaporator coils inside the freezer compartment. It directs cold air flow from the evaporator into the freezer and fresh food sections while protecting the coils from frost buildup and physical damage. Replace this cover if it is cracked, warped, or heavily frosted over, which can lead to uneven cooling or excessive ice accumulation.

This is a hinge cover designed to fit over the door hinge on a refrigerator or freezer section. It provides a finished appearance by concealing the hinge hardware and helps protect it from dust and debris. Replace this cover if it is cracked, broken, or missing, which can detract from the appliance's appearance.

This 26.7" shelf assembly replaces a damaged or missing refrigerator shelf so you can organize food safely and restore usable storage space. Built to sit on existing shelf supports and hold everyday refrigerator items. What it does:

• Provides a stable, flat surface for storing food and containers
• Replaces cracked, chipped, sagging or broken shelving
• Helps prevent spills and keeps items organized for easier access
• Matches the OEM shelf footprint and mounting points for a direct fit

• One shelf assembly (26.7")

• Remove all items from the shelf and support area before installing
• Slide or set the shelf into the existing support rails or brackets per your model's layout
• If clips or rails are damaged, replace them before installing this shelf
• Dispose of broken glass safely and wear gloves to avoid injury

Replaces a cracked or missing access cover that shields internal components in your refrigerator. Restores a finished look and keeps wiring secure.

This harness with reed switch detects a magnetic field and provides a ready-made wiring connection for the appliance's door/sensor circuit, restoring reliable sensing and signal routing. What it does

• Contains a reed (magnetic) switch in-line with a multi-conductor harness to detect open/closed or presence/absence of a magnetic field
• Replaces a damaged or faulty sensor harness that can cause intermittent or no signal to the control board
• Common symptoms: appliance not sensing door/cover, controls not responding, or features tied to the sensor fail to activate
• Designed to mate with the factory connector set and routing used by the original equipment

• One complete harness with reed switch

• Verify power is disconnected before accessing wiring or replacing the harness
• Handle the reed switch and connectors gently to avoid damage; secure harness with original clips or fasteners

Short hex washer head screw for chest freezers, upright freezers, and compact refrigerators. Replaces lost, stripped, or damaged screws to secure panels.

Fix intermittent freezer operation or power issues with this wiring harness. Restores electrical connections between components for reliable performance.

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.