Parts for Electrolux FPFU19F8WF3: 03 - Cabinet Parts

Replacement cover for upright freezer. Installs to protect internal components or provide cosmetic finish. Order if original is cracked, broken, or missing.

Replacement door hinge for upright freezers. Mounts the freezer door to the cabinet frame. Replace if hinge is cracked, bent, or no longer holds door securely.

Door hinge assembly for upright freezers. Mounts to the cabinet and door to provide smooth opening and closing. Replace if bent, cracked, or worn.

Door hinge assembly for upright freezers. Mounts to the cabinet and door to provide smooth opening and closing. Replace if bent, cracked, or worn.

This is a cover panel that fits over the lower left hinge area of an upright freezer, providing a finished appearance and protecting the hinge mechanism from dust and debris. It snaps or screws into place over the hinge hardware at the base of the unit. Replace this cover if it is cracked, broken, or missing, which can expose the hinge to damage and detract from the appliance's appearance.

The Freezer Leveling Leg is an OEM part for Frigidaire upright freezers. It stabilizes and balances the appliance on uneven surfaces.

Causes relate to typical bearing wear from years of weight support. Rust forms without protective finish. Cracks develop from impact damage.

Symptoms of compromised leveling legs include:

• Excessive vibrations, noise or shaking during compressor operation
• Doors that no longer close or seal properly
• Ice maker malfunctions on frost-free models

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Hardware screw for securing shelves, bins, and trim panels inside refrigerators and freezers. Replace when stripped, corroded, or missing during repairs.

Replace your refrigerator's interior light bulb when it burns out or flickers. Restores clear visibility inside the fresh-food compartment. Verify fit with your model number before ordering.

Replace your refrigerator's light assembly to restore interior visibility. Install when bulb housing cracks or wiring fails. Verify fit with your model.

Replaces damaged interior light assembly to restore safe, even refrigerator illumination. Install when lights flicker, dim, or fail completely. Verify fit with your model number before ordering.

This harness with reed switch detects a magnetic field and provides a ready-made wiring connection for the appliance's door/sensor circuit, restoring reliable sensing and signal routing. What it does

• Contains a reed (magnetic) switch in-line with a multi-conductor harness to detect open/closed or presence/absence of a magnetic field
• Replaces a damaged or faulty sensor harness that can cause intermittent or no signal to the control board
• Common symptoms: appliance not sensing door/cover, controls not responding, or features tied to the sensor fail to activate
• Designed to mate with the factory connector set and routing used by the original equipment

• One complete harness with reed switch

• Verify power is disconnected before accessing wiring or replacing the harness
• Handle the reed switch and connectors gently to avoid damage; secure harness with original clips or fasteners

Refrigerator won't cool properly or runs constantly? The thermistor monitors temperature and signals the control board. Moderate DIY repair.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Replace a lost or worn ice scoop to restore convenient, sanitary ice handling. This durable plastic scoop makes transferring ice easy and hygienic.

This is a glass shelf designed to fit inside the refrigerator or freezer compartment, providing a flat surface for organizing and storing food items. It sits on support brackets or rails within the interior cavity. Replace this shelf if the glass is cracked, chipped, or shattered, which can compromise food safety and storage capacity.

Fix refrigerator not cooling, temperature fluctuations, or display errors with this electronic control board. Regulates compressor and defrost cycles.

Replacement drive motor that powers an appliance's rotating components, restoring normal operation and reliable movement. Use this motor to address rotation failures and abnormal noises so the unit can run as intended. What it does

• Turns the appliance's rotating assemblies to enable normal operation.
• Helps when the appliance won't rotate, tumble or start turning even though power is present.
• Restores consistent speed and torque for proper cycle performance.

• Disconnect power before attempting any service to avoid shock or injury.
• Verify alignment and mounting orientation; secure all fasteners to manufacturer torque where specified.
• Inspect wiring harness, connector pins and any grommets for damage; replace damaged components as needed.

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic

The freezer ice maker assembly is located inside the freezer compartment and automatically produces ice cubes. It includes the ice making mechanism, fill cup, ejector arms, and collection bin. Replace when ice production stops completely, ice cubes are malformed, the unit leaks water, or mechanical parts become jammed or broken.

This replacement refrigerator drawer assembly restores a smooth, sturdy bin for organizing food items. Replace a cracked, warped, or missing drawer to regain usable storage space and proper sliding action. What it does

• Provides a sliding storage bin inside the refrigerator compartment
• Keeps items contained and organized to help prevent spills
• Restores proper fit and smooth glide when matched with undamaged rails
• Typical symptoms: cracked or broken drawer, hard to open/close, falls off tracks, won't stay seated

• 1 drawer assembly

• Disconnect power and remove contents from the drawer area
• Fully extend the old drawer, lift the front, and pull to remove from the rails/glides
• Move any removable inserts from your original drawer to the new one if required by your model
• Align the new drawer with the rails and slide it in until it seats and moves smoothly; restore power

This is a replacement drawer assembly that restores the refrigerator's storage bin so you can organize and access food easily. It replaces a cracked, broken, or missing drawer to bring back full-use storage. What it does:

• Provides a sturdy sliding bin for storing produce, deli items, or packaged foods
• Restores smooth open-and-close operation when the original drawer is damaged or stuck
• Helps contain spills and prevent items from shifting during door movement
• Fits into the factory drawer track and aligns with existing guides when installed properly

• One complete drawer assembly

• Remove power to the appliance or disconnect from the outlet before servicing
• Slide out the old drawer and lift to disengage from tracks; reverse steps to install the new drawer
• Inspect drawer tracks and guides for damage and clean tracks before installing the replacement
• Use gentle pressure to seat the drawer—do not force or bend plastic components

Complete shelf assembly for chest freezers. Includes shelf surface and support brackets. Replace when cracked, broken, or warped to restore storage space.

Replacement mounting screw for refrigerators and freezers. Secures panels, brackets, trim, and covers. Replace if missing, stripped, or damaged.

Replacement drawer slide assembly for chest freezer bins. Installs on the side rails to restore smooth gliding action. Needed when original is cracked or worn.

Replaces worn drawer slide assembly to restore smooth gliding. Install when drawers stick, drop, or misalign. Confirm fit with your model number.