Parts for Electrolux CRTE2044VW0: 05 - System Parts

Secures wire harnesses and ground wires to your refrigerator cabinet. Replace if broken or missing to prevent wire damage. Verify fit with your model.

Refrigerator not cooling properly or running constantly? This condenser coil assembly removes heat from refrigerant to restore efficient cooling performance.

Wire harness connects electronic components inside your refrigerator. Replace if wires are damaged, frayed, connectors are broken, or harness is missing.

Fixes poor cooling and warm temps caused by moisture in the sealed system. This filter-drier protects the compressor during refrigerant repairs.

This starter is the compressor's start device. It momentarily energizes the start winding so the compressor can begin running, helping restore reliable start-up and cooling when the original device weakens or fails.

• Engages the compressor's start winding at power-up, then disengages
• Helps the compressor start smoothly and reduce excessive current draw
• Failure symptoms include no cooling or intermittent cooling
• Common signs: rapid clicking, humming then shutting off, or the compressor not starting

• Disconnect power before servicing and allow components to cool
• Access the compressor terminal cover; note wiring and orientation before removal
• Photograph wiring; move wires one at a time to the new starter and seat terminals fully
• If a run capacitor is present, discharge it safely before handling the circuit

This rubber grommet cushions and protects wiring, tubing or mounting points to reduce vibration and prevent chafing. It restores a tighter fit where the original grommet has worn, torn or become brittle. What it does:

• Cushions and isolates wiring, hoses, or mounting studs to reduce vibration and noise
• Prevents chafing and abrasion where components pass through metal or plastic openings
• Helps maintain proper alignment and fit of panels or assemblies
• Common symptom: visible wear, cracking, a loose or rattling component near the grommet location

• One grommet

• Disconnect power and water before servicing the appliance
• Inspect surrounding components for damage and replace any additional worn seals
• Gently press the grommet into place; small hand tools or a blunt plastic driver may help
• If routing wires or hoses, ensure they sit fully inside the grommet to prevent chafing

This capacitor stores and releases electrical energy to help the refrigerator's compressor start and run smoothly. Replacing a weak or failed capacitor can restore reliable compressor startup and more consistent cooling performance.

• Provides the electrical boost/phase shift needed for compressor motor startup and steady operation
• Works with the start device to deliver proper current to the compressor
• Failure symptoms can include clicking or humming near the compressor, poor cooling, or short cycling
• May cause the compressor not to start after power interruptions when weak or failed

• Disconnect power before servicing any electrical component
• Safely discharge the capacitor before handling; avoid touching terminals
• Note wire positions and terminal markings; transfer leads one at a time to the matching terminals
• Secure the capacitor in its mounting/bracket to prevent vibration damage

This tube is a direct-replacement plumbing/air line used in compatible Frigidaire appliances to route fluid or condensate. It restores proper flow and helps prevent leaks or pooling when the original tube is damaged or clogged. What it does:

• Channels water or condensate away from components to the appropriate drain or collection area
• Prevents leaks and water pooling caused by cracked, split, or collapsed tubing
• Helps restore normal dispenser/drain operation when original tubing is blocked or deteriorated
• Works as a simple, low-risk part to replace during troubleshooting of water-routing issues

• One replacement tube as shown

• Inspect the existing routing and connections before removal; replace with identical routing to avoid kinks or interference
• Use appropriate clamps or fittings and tighten securely to prevent leaks
• Disconnect power and water supply as applicable before servicing to prevent shock or flooding

Water pooling under your refrigerator? This drip pan collects defrost water and condensation to prevent leaks. Direct-fit replacement part. Easy DIY.

This is a small electric condenser fan motor (115V, 60Hz, 2.7W) that mounts near the compressor at the bottom or rear of the refrigerator. It drives the fan that pulls air across the condenser coils to release heat from the refrigeration system. Replace this motor if the refrigerator is running warm, the compressor is overheating, or you no longer hear the condenser fan running when the compressor is on.

The Condenser Fan Motor is an OEM part for Frigidaire refrigerators. Located behind the rear refrigerator wall and grille, the condenser fan motor works to dissipate heat from within the refrigerator system. 

Symptoms of a bad condenser fan motor include:

• Refrigerator failing to adequately cool or ice up  
• Increased humming and vibrations
• Elevated compressor run times 
• Warm air discharge from rear grill

Causes of a bad condenser fan motor can include winding failures, bearing seizing, or obstructed fan blades no longer spinning freely.

This genuine OEM Frigidaire motor is compatible with some Electrolux, KitchenAid and Danby French door refrigerator models as well.

This baffle channels cold-air inside the refrigerator compartment to help maintain consistent temperatures and efficient cooling. It replaces a damaged or missing baffle to restore proper airflow and temperature balance. What it does:

• Directs and controls airflow from the evaporator into the fresh-food compartment
• Helps maintain even temperatures and reduce hot spots
• Prevents direct airflow that can freeze exposed items or cause frost buildup
• Restores proper circulation when a cracked, warped, or missing baffle causes performance issues

• Disconnect power to the appliance before starting any repair
• Remove any shelves or drawers that block access to the baffle
• Align tabs or mounting points and snap or secure the baffle into place per the service manual

Fixes excess frost buildup on evaporator coils in top-mount refrigerators. This defrost heater melts ice during scheduled cycles, restoring cooling.

This support mounting bracket secures and steadies a key appliance component, helping maintain proper alignment and reliable operation. It's a direct-fit replacement designed to restore part stability and reduce movement-related issues. What it does:

• Provides structural support and alignment for the associated assembly
• Helps prevent sagging, misalignment, or excessive vibration of the component
• Restores reliable mounting after a cracked, bent, or missing support
• Supports normal operation by keeping parts correctly positioned

• One support mounting bracket

• Install with factory-recommended fasteners; inspect surrounding parts for wear before reassembly
• Use basic hand tools; avoid overtightening fasteners which can deform the part
• Disconnect power to the appliance if required to access the mounting area

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.