Parts for Amana ARS2664BS / PARS2664BS0: 06 - Façade, Controls & Light Shield Parts

Replace your refrigerator water filter every 6 months to ensure clean, fresh-tasting water and ice. Easy twist-on installation. Verify fit with your model.

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

Color: Black

This replacement grille sump (drip tray) catches condensation and minor overflows beneath the appliance to help protect cabinets and floors from water damage. Direct-fit, black finish for a discreet repair. What it does

• Collects and channels water away from the appliance base to reduce pooling under the cabinet
• Replaces cracked, warped or missing sump that can cause visible leaks or water stains
• Restores the original drainage path so trays and drains perform as intended
• Helps stop water from contacting sensitive components under the appliance

• Disconnect power (and water if applicable) before accessing the appliance base or removing panels
• Remove the lower access panel/kickplate to access the sump; note orientation before removal
• Seat the new sump into the locating tabs/slots; ensure a snug, gap-free fit

6 - 19 x .250

Fix a dead display panel or non-responsive controls with this refrigerator control board. Common when lights go out or buttons stop working.

Replace your refrigerator water filter every 6 months to ensure clean, fresh-tasting water and ice. Easy twist-on installation. Verify fit with your model.

This limit switch monitors a set condition and opens or closes its contacts when that limit is reached. Replacing a failed switch restores proper safety cutoff and consistent operation of the appliance's heating or movement system. What it does:

• Senses a limit condition at its mounting point (such as temperature or travel/position, depending on model)
• Changes state at a defined threshold to protect components and wiring
• Interrupts power to heat or motor circuits, or signals a control to respond
• Common failure signs: no heat or shuts down early, runs continuously, won't start, or intermittent operation

• 1 limit switch

• Disconnect power to the appliance before servicing
• Note wire positions; transfer connectors one at a time or take a photo for reference
• Reinstall in the original orientation so the actuator or sensing surface contacts the correct area
• Address root causes (blocked airflow, binding mechanisms, shorted components) to prevent repeat failures

This decorative identification nameplate replaces a worn, damaged, or missing Amana Plus front badge to restore appliance appearance and legibility of branding/details. It's a simple cosmetic replacement that keeps the exterior looking finished. What it does:

• Replaces a faded, scratched, or missing Amana Plus nameplate on the appliance exterior
• Restores readable product branding and identification on the front panel
• Improves overall appearance after cosmetic wear or accidental damage
• Helps owners quickly identify the model area without guessing

• Turn off and unplug the appliance before starting any work near electrical components.
• Clean and dry the mounting area so the nameplate adheres or seats properly.
• Remove any remaining adhesive or clips from the old plate before installing the new one.
• Align carefully and press firmly; if fasteners are present on your model, retain and reuse as needed.

Black toe grille assembly installs across the bottom front of your refrigerator. Replace a cracked, broken, or missing kickplate to restore appearance.

Replacement cap for refrigerator door handle. Covers exposed hardware on freezer or fresh food compartment handles. Needed when original is cracked or missing.

Size: 8 x 1-1/4 inch.

Freezer icing up or fridge warm while freezer works? The defrost timer controls defrost cycles. DIY-friendly fix in about 1 hour, saves $150+ on service.

Fridge not cooling or freezer running too warm? This temperature control regulates freezer temp by cycling the compressor. DIY-friendly repair.