Parts for Electrolux FRSC2333AS2: 09 - Ice Container Parts

Ice not dispensing or spilling in freezer? This ice container assembly collects and stores ice from your ice maker. Durable molded bin design.

This drive bar connects the ice dispenser motor to the auger inside the ice bucket, transferring rotational force to push ice toward the dispenser chute. It is a metal or reinforced plastic linkage that fits between the motor shaft and the auger assembly. Replace this part if the dispenser motor runs but ice does not advance, or if the drive bar is visibly worn, stripped, or broken.

This motor drives the auger that pushes ice from the ice bucket through the dispenser chute when you press the dispenser lever. It converts the motor's rotational force into the turning motion of the auger spiral. Replace this motor if ice is not dispensing, the auger does not spin, or you hear a humming sound without movement when attempting to dispense ice.

This is a wiring harness that connects the ice maker to the refrigerator's main electrical system, supplying power and control signals needed for ice production. It routes between the ice maker module and the main control board or power source. Replace this harness if the ice maker stops producing ice, works intermittently, or if the wires show signs of damage, corrosion, or loose connections.

This housing is the main outer enclosure that secures and protects internal components, restoring proper fit and finish to the appliance. It provides structural support and helps keep wiring and assemblies in place. What it does:

• Replaces damaged, cracked, or warped outer housing panels that allow components to shift or be exposed
• Restores proper alignment and support for internal parts and mounting points
• Helps prevent wiring or components from rubbing, chafing, or being exposed
• Improves appliance appearance by replacing a broken or discolored enclosure

• One housing

• Disconnect power (and water, if applicable) before beginning any repair
• Remove fasteners and panels carefully to avoid breaking mounting tabs; save hardware for reinstallation if reusable
• Use basic hand tools; some models may require loosening adjacent panels for access
• If clips or mounting tabs are damaged, replace them to ensure a secure fit

Outer housing shell for refrigerators. Provides structural support and protects internal components. Replace if cracked, damaged, or worn to restore fit.

Mounting screw for refrigerator components and panels. Replaces lost, stripped, or damaged screws. Essential hardware for secure assembly.

This housing cover protects and secures the motor and solenoid assembly, helping maintain proper alignment and safe operation. Restores the cabinet fit where the original cover is cracked, missing, or worn. What it does

• Provides a protective enclosure for the motor and solenoid assembly to prevent debris and moisture intrusion
• Keeps motor/solenoid components properly positioned for reliable engagement
• Helps reduce vibration noise caused by loose or damaged covers
• Commonly replaced when the cover is cracked, broken, or no longer holds fasteners

• Verify power is disconnected before beginning service to avoid electrical shock
• Handle fasteners and mounting tangs carefully; replace any damaged clips or screws as needed
• Basic disassembly of the appliance access panel may be required;

Fixes incorrect temperature readings and short cycling. This thermistor monitors fridge temps and signals the control board. Moderate DIY repair.

Secures panels and components in your refrigerator to prevent rattling and misalignment. Replace if trim pieces are loose or parts shift. Verify fit with your model number.

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Spacer that fits between refrigerator door hinge components to maintain proper clearance and alignment. Replace if worn, cracked, or missing.

Refrigerator spacer maintains proper clearance and alignment between internal parts. Replace if worn, missing, or causing parts to rub or bind together.

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

Secure solenoid clip for refrigerators. Replace if damaged, loose, or missing to ensure proper solenoid function. Confirm fit with your model number.

Actuator spring for refrigerator solenoid mechanisms. Replaces broken or worn springs that cause poor movement or engagement. Restores tension.

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

Fix refrigerator controls that won't respond or move properly with this solenoid actuator. Restores electromechanical action when worn parts fail.

Secures ice crusher components in place. Replace if pin is worn, missing, or broken to restore proper alignment and operation of crusher assembly.

Metal flat washer for refrigerator ice maker auger and other assemblies. Replaces worn, missing, or damaged washers during repairs and reassembly.

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

Replacement mounting screw for refrigerators and freezers. Secures shelves, handles, panels, and brackets. Replace missing, stripped, or rusted screws.

Mounting screw for refrigerator assembly. Secures components and panels inside your appliance. Replace if screw is stripped, missing, or damaged.

Replace your refrigerator's air duct assembly. This duct directs cold air flow between compartments. Order a new one if cracked, broken, or missing.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Machine screw secures panels, trim, and internal brackets in your refrigerator. Replace worn, stripped, or missing fasteners to keep components aligned.