Parts for Maytag A108: 11 - Power Unit & Center Assembly Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Seals the agitator shaft opening to prevent leaks and protect internal components. Replace if you see water leaking from the center post during wash cycles.

Seals the agitator shaft opening to prevent leaks and protect internal components. Replace if you see water leaking from the center post during wash cycles.

Fix agitator wobble and excessive vibration with this retaining washer. Secures center-mounted components to prevent looseness and noise during operation.

Specialty lubricant for washer transmission center seals. Replace when servicing seals or bearings to ensure smooth operation. Confirm fit by model.

This part has been discontinued and is no longer available.

This part has been discontinued and is no longer available.

Supports the inner tub for smooth spinning during wash cycles. Replace when you hear grinding noise or see water leaking from bottom center of tub.

This repair kit contains seals and components needed to fix leaks around the washer's tub mounting stem. It prevents water from escaping the wash basket area during operation. Use this kit when you notice water pooling under your washer or leaking from the tub assembly.

This repair kit contains seals and components needed to fix leaks around the washer's tub mounting stem. It prevents water from escaping the wash basket area during operation. Use this kit when you notice water pooling under your washer or leaking from the tub assembly.

This repair kit contains seals and components needed to fix leaks around the washer's tub mounting stem. It prevents water from escaping the wash basket area during operation. Use this kit when you notice water pooling under your washer or leaking from the tub assembly.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Supports the inner tub for smooth spinning during wash cycles. Replace when you hear grinding noise or see water leaking from bottom center of tub.

Creates a tight barrier between washer components to prevent water leaks. Replace when original becomes cracked, flattened, or brittle. Confirm fit by model.

A small trim screw designed to secure appliance trim pieces and molding, restoring a finished look and keeping panels held firmly in place. Ideal when a trim piece is loose, missing a fastener, or shows minor rattling. What it does:

• Fastens trim, molding, or decorative panels to the appliance frame
• Restores secure mounting and helps eliminate loose or rattling trim
• Replaces missing or stripped fasteners that cause gaps or poor fit
• Compatible with common trim attachment points where OEM screw is specified

• Disconnect power or unplug the appliance before attempting repairs
• Use the correct screwdriver bit to match the screw head to avoid stripping
• Install by hand to start threads, then tighten snugly—do not overtighten
• Verify trim alignment after installation and test that the panel is secure

This small spacer washer fits in the washer's drive assembly to set the correct clearance between mating parts. Proper spacing helps components rotate smoothly and quietly while minimizing metal-to-metal contact and premature wear.

• Maintains the specified gap and alignment within the drive/brake or pulley stack
• Helps reduce friction, rubbing, and vibration
• A worn, distorted, or missing spacer can contribute to scraping or grinding noises and excess play
• Often replaced during service of related drive components to restore correct stack order

• Disconnect power before servicing; shut off water if moving the appliance
• Access and procedure vary by model—refer to your unit's service manual or parts diagram for the correct stack order
• Support the appliance if working from below; remove belt/pulley or related parts as required
• Reassemble in the exact order and orientation; verify free rotation before test-running

Torx-head screw set secures panels and components throughout your laundry center. Replace worn, stripped, or missing fasteners to keep parts tight.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.