Ace Leaf Blower Parts

A flange nut's unique wide flange design distributes the nut's pressure over the part it is securing. In return, it creates an even fastening surface, which reduces part damage and nut loosening. This one-piece all-metal fastener has a lock nut version that features a protruding circular flange. This drastically increases bearing surface, compatibility either for irregular or oversized holes, and surface tension reduction. Flange lock nuts are the preferred type of fastener for many lawnmower models because it can provide better fastening than regular screws, which are known to loosen under extreme vibration. However, it’s important to know that flange lock nuts are susceptible to wear and tear due to constant vibration exposure. It is essential to replace the broken flange lock nut immediately to prevent serious damage to the lawnmower. The MTD 712-04063 Flange Lock Nut OEM replacement can be used with Craftsman, White Outdoor, Yard Machines, MTD, or Columbia lawnmowers. It is a genuine or OEM MTD replacement part that measures 5/16-18. It is threaded and requires the use of a wrench. This replacement flange lock nut is sold individually. An MTD bolt carriage may also be needed and is sold separately.

A carburetor is responsible for combining fuel and air into the right combustible mixture. When it is malfunctioning, there are several warning signs to look out for. These include poor fuel economy, rough idle, flooding, and engine misfire. Installing a brand-new carburetor can help. A carburetor replacement is easy and starts with turning off the lawnmower. Open its air filter cover and use a screwdriver to remove the air filter base. Once detached, disconnect the throttle cable and fuel line. Place the new carburetor and connect the fuel line and the throttle cable. Put back the air filter base. This is a brand-new and original MTD carburetor. It is compatible with tillers, leaf blowers, and string trimmers from MTD, Bolens, Craftsman, Troy-Bilt, Yard-Man, and Yard Machines. This carburetor is fully assembled and sold individually. Additional carburetor gaskets are sold separately.

This carburetor is a device for supplying a two-cycle engine with a mixture of air and fuel. This part comes pre-assembled and has a plastic choke lever along with a metal body. The primary purpose of a carburetor is to mix the right amount of fuel with air so that the engine runs properly. If enough fuel is not mixed with the air, the engine runs lean and can either stop running or gets damaged. On the other hand, if too much fuel is mixed with air, the engine runs rich, and it either floods, runs poorly, runs very smoky, or wastes fuel. The carburetor is in charge of getting the right mixture. If the carburetor is clogged, the engine will not get enough fuel. It may not start or may run rough. The procedure to replace the carburetor is quick and easy, taking only around 15 minutes, but it is recommended to work in a ventilated area. This carburetor works with outdoor power tools like the trimmer, leaf blower, and tiller. It is compatible with specific products from popular brands like Craftsman, MTD, Murray, and Troy-Bilt. It is sold individually and is supplied directly from the original equipment manufacturer.

A carburetor needs fuel to produce the required combustible mixture of air and gas. To get fuel, the carburetor draws the liquid directly from the fuel tank. Any excess fuel will be returned to the tank through the fuel return hose or fuel return line. In addition to providing the path, a fuel line is also responsible for preventing over-pressurization, as well as vapor lock. A fuel return line is constructed from a thick rubber material that is also fuel resistant. However, it may still become brittle and crack due to regular wear and tear. Usually, a broken fuel return hose results in symptoms such as engine misfires, loss of power, carburetor flooding, fuel leaks, and hard starting. A brand-new replacement is available here. This fuel line return is an original part from MTD. It measures 3.78 x 3.78 x 0.016 and is compatible with tillers, leaf blowers, and string trimmers made by Craftsman, Ryobi, Yard Machines, MTD, Bolens, and Yard-Man. Installation will require a screwdriver, cutters, and pliers. This fuel line return is sold individually.

A flange lock nut, also known as a flange lock or a lock nut, is created to be used in various types of lawn and garden equipment. This flange lock nut holds other parts in place and, when properly threaded, will resist loosening. Over time, a flange lock nut may begin to weaken and may become loose or break. If it appears to be broken or weak, a replacement is required. Flange locks can be adjusted and uninstalled after use. When replacement is required, you may need a socket set, screwdriver, hacksaw, and butane torch. The socket wrench will loosen the bolt it is connected to, while the torch is used to heat the lock nut. A socket wrench may remove the nut, but sometimes cutting it with a hacksaw is required. This flange lock nut is a genuine OEM component directly from the manufacturer and comes in an individual unit. It is made of metal, a gold color, and can be found in various areas of lawn equipment. It works with lawnmowers, trimmers, snowblowers, cultivators, tillers, and leaf blowers by Poulan, MTD, Toro, Cub Cadet, Murray, Troy-Bilt, Bolens, Yard Machines, Craftsman, and Yard-Man.

A carburetor gasket is a thin rubber material that provides a seal between two parts. Its primary purpose is to prevent fuel and air leaks. This gasket is installed between the air cleaner and the carburetor. Over time, it can crack and tear due to heat and fuel exposure. When this happens, the carburetor may produce the wrong combustible mixture for the engine. In return, the engine may experience rough idling and flooding. A carburetor gasket replacement is necessary. MTD makes this carburetor gasket replacement. It is manufactured to fit string trimmer, leaf blower and tiller made by MTD, Bolens, Troy-Bilt, and Craftsman. This brand-new carburetor gasket is sold individually. A fully assembled carburetor and O-ring are sold separately.

This is a replacement spark plug that is designed specifically to be used with select string trimmers. the spark plug is connected to the ignition module and is responsible for creating the spark that starts the internal combustion engine. Over time, the electrode on the spark plug will wear down. Other issues can also arise that cause the spark plug to foul or stop working. Spark plugs are part of routine maintenance on any engine, but most owners keep a spare or two around just in case of emergencies. In the event that the spark plug is bad, the engine will not start. This genuine OEM spark plug is manufactured by MTD and designed for use in select trimmers. It is compatible with over 50 models of string trimmers from MTD, Bolens, Murray, Troy-Bilt, Yard Man, and Cut Cadet. Owners will need to consult their product diagram or manual to find the exact gap for the spark plug when replacing them. Many models claim to come pre-gapped, but they can settle during shipping and should always be re-gapped prior to installation. This is sold as an individual unit. Be sure to wear gloves for hand protection when replacing spark plugs and performing other maintenance.

These O rings are replacement parts intended for use in a number of gasoline-powered lawn trimmers. The O rings serve as gaskets and are placed at the entry and exit points in the carburetors where gasoline and air are mixed and the expansion powers the trimmer. Though constructed of durable material, periodically the flow of the air/fuel mix or the rush of expanding air will cause damage to occur to the O rings so they become less resilient and the carburetor functions less efficiently. In these cases, users often decide to replace not just the element of the carburetor but the O rings as well. Users may notice problems with the carburetor when they cannot get an adequate adjustment, allowing the trimmer to function smoothly. They may also have trouble getting the trimmers to start at all or run without smoking. To replace the O rings, remove the air filter cover and carburetor. Once the carburetor has been cleaned, and the gasket and filter replaced, add a fresh mix of 40:1 fuel. The trimmer should start immediately. These OEM certified O rings are compatible with Bolens, Troy-Bilt, Yard Machines, and Craftsmen trimmers.

This OEM replacement push cap can be used in a variety of lawn and garden equipment. The push cap is secured to the end of a shaft, providing protection to the user from the sharp metal edge of the shaft. The push caps that are included with the machines may wear out over time or fall off in some cases, creating an injury risk involving sharp metal edges. These push caps are high-quality and made from durable plastic. They are easy to install. The OEM push cap is a genuine part made by the original manufacturer, to ensure quality and s proper fit. The push caps can be used on lawn tractors, chippers, shredders, log splitters, and other equipment. Some of the brands that this push cap is compatible with include MTD, Husky, Yard-Man, Bolens, Troy-Bilt, Ryobi, Yard Machines, and cub Cadet.

A star knob connects the upper and lower handles on an outdoor appliance, and if removed, the upper and lower handles are quick-released. This part is made of black heavy-duty black plastic, and the threads are made of steel. Over time, the threading can become worn out, making the connection loose, and causing the two handles to no longer stay in place. Star knobs are a straightforward repair that can be done in a matter of minutes. Just unscrew the original, damaged knob and screw in the new knob. The knob is designed to be unscrewed by hand, so there is no need for additional tools to make this repair. This genuine OEM replacement part is designed for a variety of outdoor appliances, including lawnmowers, edgers, chippers, tractors, trimmers, and cultivators. This star knob is compatible with Yard Machines, Yard-Man, Cub Cadet, Bolens, Craftsmen, and Ryobi products. This part ships individually.

The plastic fuel tank is responsible for storing the fuel that will be used by the lawn and garden equipment. The fuel tank is meant to be durable. However, this does not mean that it can't become broken. Damage to the fuel tank could cause a leak, which could be dangerous and waste fuel. Whether it is through wear and tear or an accident that causes a problem with the gas tank, such as a hole, it will need to be replaced. This is a genuine OEM replacement fuel tank that will work with string trimmers, edgers, and leaf blowers. It is compatible with models from Craftsman, MTD, Cub Cadet, and Troy-Bilt. It is important to note that this product is sold individually. It does not come with the fuel cap that will be needed to keep the fuel tank safe from an influx of air and debris. The cap will need to be purchased separately. Buyers should always make sure the tank they are choosing will work with their make and model.

This impeller can be used as a replacement part for the small engine of a leaf blower or a leaf vacuum. The function of an impeller, which operates by rotation, is to take in the leaves and eject them out of the chute.An impeller might have to be replaced if it suffers damage that impedes it from properly ejecting the leaves from the chute. A common symptom of an impeller that needs to be replaced is that the leaves are not ejected with enough force from the chute or that the ejection process stalls or does not occur at all. If this is the case, the impeller should be removed and replaced with this genuine OEM replacement part immediately before using the leaf blower or leaf vacuum again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, MTD, and it is sold individually. This impeller is compatible with the following brands: MTD, Troy-Bilt, and Yard Man.

This fuel cap assembly fits on the lawn tractor fuel tank to keep the fuel inside and debris outside. The part is red and has a gas pump embossed on it for added identification. The top of the cap also features vent slots to allow hot air to escape and prevent heat expansion. It features a gasket under the cap to keep gas from sloshing out during operation. The fuel cap assembly is made of heavy-duty plastic that can fade and crack due to the elements. Removal and replacement are as simple as taking the old cap off and putting the new cap on. Hand-tighten to prevent gas from leaking. Never over-fill the fuel tank. Leave room for the oil additive if it is not mixed before fueling. This fuel cap assembly is a genuine OEM replacement part sourced directly from the manufacturer. It is sold as an individual unit. This fuel cap is designed for use in lawnmowers and lawn tractors manufactured by MTD, Ryobi, Troy-Bilt, Bolens, Yard-Man Yard Machines, Cub Cadet, and Murray.

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.

This is a flange nut that can be used in a variety of lawn and garden equipment from different manufacturers. The nut is made of metal, measures 5/16x18, and is used to secure components in place. It also assists with preventing backing out caused by vibration. Over time, the flange nut can become damaged and will need to be replaced. If the flange nut in lawn and garden equipment has become damaged, is loose, or gets lost, then replacement is required. The level of difficulty of replacing a flange nut depends on which parts it's securing and what kind of equipment it is installed on. This flange nut is an OEM replacement part that can be used with lawn mowers, snowblowers, wood chippers, tillers, log splitters, leaf blowers, and edgers by MasterCut, Craftsman, Yard-Man, Toro, Bolens, Cub Cadet, Montgomery Wards, Ryobi, Huskee, Troy-Bilt, MTD, and Yard Machines. It is sold individually and will require a wrench or socket for installation.