Ace Snow Removal Equipment Parts

This set of two slide shoes is a genuine OEM replacement parts-set for a snowblower. Slide shoes rest on the bottom of the auger housing and help it to glide smoothly against the ground. This lets the auger gather snow without the housing bumping up and down. Every snowblower has two slide shoes: one on each side of the auger housing. They are positioned so that the center openings face outwards. Slide shoes take a lot of abuse while sliding along the ground. Even though they are made of sturdy steel, they can still be banged and dented to the point that they need replacing. If heavily dented, they may no longer glide smoothly and impede the blower's effectiveness. To replace damaged slide shoes, use a socket wrench to unbolt them from the auger housing. Be sure not to lose the mounting bolts, as they will be used for reassembly. This set of slide shoes is designed to be used with Huskee, MTD, Yard Man, and Yard Machines snowblowers. It comes sourced from its original manufacturer and includes two slide shoes. This set does not include any of the hardware required for assembly.

This grease plug is a genuine OEM replacement part sourced directly from the manufacturer. It is found on snowblowers and other outdoor yard machines on the gearcase assembly, which houses the auger gear. The grease plug seals the oil port on the gearbox. This keeps lubrication inside the gearbox and is the access point for adding more when needed. If this plug is lost, the gearbox's oil could leak out, and contaminants could get into the gearbox.Lubricate the contents of the gearbox before installing the new grease plug. Locate and remove the two screws on the side to drain the gearbox. Install the grease plug in the bottom. Refill the oil using the vent hole. Continue filling until oil is coming out the top side screw. Close everything back up, and the machine is ready for use. To prepare the equipment for long storage, remove the grease plug and check the oil level. If it is not to the top, add more lubricant before sealing the grease plug.This grease plug is made of durable black molded plastic and is sold as an individual unit. It is compatible with snowblowers and snow throwers manufactured by Ryobi, MTD, Yard Machines, Troy-Bilt, Bolens, Yard-Man, Cub Cadet, and Husky.

This replacement part is a bolt. This is a genuine replacement part made by MTD. This part is small but important to the overall workings of the machine. Bolts work with other parts such as screws and nuts to ensure that different parts are held in place and are secure during use. A new bolt might be needed if the current one has become loose, is missing, or has been damaged. This can include being dented, bent, or lodged in place. Be sure to replace it as soon as possible if this is the case. This should be a fairly simple repair and only require common household tools such as a screwdriver and pliers. This part is sold individually and is sourced directly from the manufacturer. This is a genuine OEM replacement part.

This ignition switch cap is a genuine MTD part, sold individually. This ignition switch cap can be used as a replacement part in lawn mowers and snowblowers. The purpose of the ignition switch cap for one of these small engine outdoor appliances is to protect and cover the ignition switch.The ignition switch cap can be damaged to the point of exposing the ignition switch. If this occurs, it should be removed and replaced by this genuine OEM replacement part with the intention of protecting the ignition switch.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This ignition switch cap is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Yard Machines, Huskee, Montgomery Wards, and Yard-Man.

This genuine OEM part is a compression spring for a lawnmower. The compression spring is the spring that holds the mower deck onto the lawnmower. Over time, the compression spring can become degraded due to excessive wear and tear. If it is no longer securing the mower deck, it will need to be replaced. Luckily, replacing this part is a relatively simple process.To replace the spring, make sure the mower deck is set to the lowest position. Locate the old retainer spring and pull it out and away from the mower. Once removed, slide the new spring into its proper position. Make sure it fits tightly, and the mower deck is secured. Once secured, power the mower to see if the spring stays in place during operation. If it does, then the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

This part is a replacement wheel axle. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current wheel axle is defective, this part can be used as a replacement. It is intended for use with a variety of snow blower models.The wheel axle attaches the wheel to the frame of the snow blower and allows it to rotate. If the axle is broken or in any way defective, the user may have trouble maneuvering the snow blower. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this wheel axle, the appropriate owner's manual and equipment diagrams should be referred to. This wheel axle is suitable for use on a variety of snow blower models manufactured by MTD, Craftsman, and other brands. It is a genuine OEM part and thus is made of high-quality, durable materials. Part sold individually.

This cam rod, also called a rod cam or a cam-rod, is a genuine MTD part. It is manufactured as a replacement part for snow blowers and snow throwers from a number of makers.This rod is long and thin, and although the original is made from durable material, it can become warped or damaged over time. It is an important component in the push function of the machine and must be replaced if damaged for safety purposes.This cam rod is a genuine OEM part which is sourced directly from the manufacturer. It is sold individually. It is compatible with snow blowers and snow throwers made by ACE, Craftsman, Huskee, Husky, Lawn Chief, Montgomery Ward, MTD, Power Pro, Ranch King, Ryobi, Select Series, White Outdoor, Yard Machines, and Yard-Man. Many of the compatible machines were made in the 1990s.

This part is a throttle control box assembly. The throttle controls the amount of air or fuel that enters the engine and also controls the speed of the engine. This assembly includes a throttle control knob that allows the user to control the throttle and the speed of the outdoor power equipment machine.A new throttle control box may be needed if any part of the assembly is cracked, broken, or damaged in any way. It's important to remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine MTD throttle control box assembly and is an OEM part sourced directly from the manufacturer and it is sold individually. This specific throttle control box assembly is compatible with edgers and lawn tractors that are manufactured by MTD, Yard Man, Yard Machines, and Cub Cadet.