Admiral Refrigerator Wire, Harness, Power Cord

This is a replacement power cord that supplies electrical power from a wall outlet to your appliance. A fresh cord helps ensure safe, reliable power delivery when the original is damaged, overheated, or worn.

• Delivers household power to the unit's main electrical connection
• Replace if the cord is cut, cracked, burnt, loose, or intermittently powers the appliance
• Helps resolve issues like no power, tripping breakers, or visible cord damage

• Unplug the appliance and turn off the circuit breaker before starting
• Verify outlet type and cord routing match your original installation
• Transfer any cord clamp/retainer as needed and secure against sharp edges
• Inspect for proper grounding and test operation before returning to service

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

Replacement power cord that restores the electrical connection so your appliance receives safe, consistent power. Use this cord to replace frayed, damaged, or non-functioning cords and help return reliable operation to the appliance. What it does:

• Restores the appliance's main power connection so it can turn on and operate.
• Commonly used when a cord shows frayed insulation, exposed wires, scorch marks, or intermittent power.
• Can address issues where the appliance does not power on due to a broken or damaged cord.
• Replaces cords with loose or damaged plug/terminal connections that may cause sparking or overheating.

• Always disconnect power at the breaker or unplug the appliance before inspecting or replacing the cord.
• Verify the cord configuration (3-prong vs. 4-prong) and terminal type match your appliance and local electrical code before installation.
• Use proper strain relief and routing to prevent pinching; secure all connections and replace any damaged terminal hardware.

This control harness connects the appliance control board to front-panel components, restoring proper signal and power routing for the console and associated controls. It replaces a damaged or faulty cable assembly to help recover responsive controls. What it does:

• Carries power and signal between the control board and user interface components
• Replaces frayed, burned, or broken wiring that causes intermittent or no console response
• Restores proper connections when buttons, lights, or display are unresponsive or operate erratically
• Prevents shorts and poor connections caused by damaged terminals or insulation

• Disconnect power (unplug or shut off breaker) before starting work
• Remove access panels per service instructions to reach the control and routing channels
• Note connector locations and routing; transfer clips and grommets to the new harness as needed
• Confirm secure, fully seated connectors and intact strain reliefs before restoring power

This refrigerator light harness connects the lamp socket to the cabinet wiring so the interior light operates reliably when the door opens. Replaces a damaged or disconnected fridge light wiring harness to restore interior illumination. What it does:

• Provides electrical connection between the fridge light socket and the cabinet wiring.
• Replaces frayed, pinched, or corroded wiring that can cause the light to flicker or fail.
• Helps restore consistent interior lighting when the door switch is closed.
• Compatible with the original lamp socket and cabinet connector design.

• Disconnect power to the appliance before inspecting or replacing the harness.
• Handle the lamp socket and wiring gently to avoid damaging the bulb or connectors.
• Route the new harness along the original path and secure any clips or retainers.

This wire harness routes power and signals through the refrigerator mullion to connect door controls and components, restoring reliable electrical continuity and control function at the door interface. What it does:

• Connects mullion-mounted controls, lights or sensors to the main appliance wiring
• Re-establishes broken or damaged wiring paths that can cause intermittent or non-working door features
• Prevents loose or frayed wiring that can cause erratic operation or electrical faults
• Provides the correct plug-and-play connector layout for a direct replacement

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Remove the mullion/door trim per the appliance service instructions to access the harness routing
• Handle connectors by the plug body; do not pull on wires when disconnecting or connecting
• Route the harness without pinching; inspect connectors for corrosion and secure all fasteners