Admiral Refrigerator Hose Or Tube

The Ice Maker Water Line is an OEM part for Whirlpool refrigerators. It supplies water from the household plumbing to the ice maker, ensuring a consistent and reliable production of ice cubes. This kit includes a 1/4-inch plastic water line that is approximately 72 inches long. The tubing will need to be cut to match the desired length.

Causes of a bad water line can include wear and tear from prolonged use, kinks or bends restricting water flow, or leaks due to punctures or cracks. A compromised water line can result in inadequate ice production or water leaks.

Symptoms of a bad ice maker water line include:

• Reduced or no ice production
• Leaking water from the refrigerator
• Visible cracks or damage to the water line
• Ice cubes that are smaller than usual

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Line Union is an OEM part for Whirlpool refrigerators. It connects sections of the water line, ensuring a secure and leak-proof connection that facilitates the proper flow of water to the ice maker and water dispenser.

Causes of a bad water line union can include wear and tear from prolonged use, exposure to fluctuating temperatures, or physical damage from handling.

Symptoms of a bad water line union include:

• Leaks or water pooling around the refrigerator
• Reduced water flow to the dispenser or ice maker
• Water line disconnections
• Visible cracks or damage on the union

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Icemaker Fill Tube is an OEM replacement part for Whirlpool refrigerators. It delivers water to the icemaker, allowing it to produce ice cubes. It is responsible for directing water from the water inlet valve to the icemaker tray, where it freezes into ice cubes.

A bad fill tube can occur due to wear and tear, blockages, or damage. If you notice symptoms such as no ice production, leaking water, or ice cubes with an unusual shape or size, it may be time to replace the fill tube.

Symptoms of a bad fill tube include:

• No ice production or limited ice output
• Leaking water around the icemaker area
• Irregularly shaped or oversized ice cubes

Repair your refrigerator by replacing the faulty or damaged fill tube with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Size: 1/4 inch. Nut for plastic water line.

Ice maker water line: 1/4x 8ft.

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

Contains two, six foot long braided hoses with 90 degree ends.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Size: 1/4" to 1/4" John Guess coupler. Compression fitting is also acceptable.

This right-angle elbow fits between the water supply line and the refrigerator's icemaker fill tube. It directs water cleanly into the icemaker and helps maintain a sealed connection to reduce drips and leaks. What it does:

• Connects the inlet water tubing to the icemaker fill tube at a 90-degree angle
• Routes water into the icemaker during the fill cycle
• Helps maintain a watertight connection at the rear of the cabinet
• Common symptoms: leaking behind the refrigerator, slow or no ice production, ice buildup near the fill area

• 1 fill tube elbow fitting

• Unplug the refrigerator and turn off the water supply; relieve line pressure before starting
• Access the rear lower area, place a towel for any residual water, and locate the elbow at the fill tube connection
• Release the clamp or retainer, disconnect the tubing, seat the new elbow fully, and resecure the line
• Turn water back on, check for leaks, then restore power and monitor the first ice fill

Made by Whirlpool. This kit includes 15 feet of copper tubing, saddle valve, teflon tape, and tubing connector. Use this kit to connect your refrigerator ice maker to water supply (usually your water shut off valve under the kitchen sink).

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

This fill hose carries water from the home supply to the appliance inlet valve, restoring proper water fill and helping prevent leaks when the original hose is cracked, worn, or blocked. Ideal for replacing damaged inlet lines. What it does:

• Delivers water from the household supply to the appliance inlet valve for normal fill cycles.
• Replaces cracked, split, or deteriorated hoses that can cause leaks at connections.
• Resolves symptoms such as slow or no water fill, visible leaks, or intermittent filling.
• Durable replacement designed to match OEM routing and connection points.

• Always shut off water supply and disconnect power before starting work.
• Inspect and replace hose clamps or inlet gaskets as needed; ensure proper seating to prevent leaks.
• Hand-tighten fittings and secure clamps—avoid overtightening metal fittings.
• After installation, restore water and power and run a short fill cycle while checking for leaks.

5 foot. Package of 2.

Kit contains two 10 feet inlet hoses.

This waterline assembly supplies water from the household line to the refrigerator's ice maker and/or water dispenser, restoring reliable water flow and preventing leaks from damaged tubing. Ideal when the fridge isn't filling or water is leaking. What it does

• Carries water from the home supply to the refrigerator ice maker/water dispenser
• Replaces cracked, pinched, or leaking tubing that causes visible leaks or puddles
• Restores normal fill to the ice maker and consistent water flow to the dispenser
• Helps eliminate slow or intermittent fill issues caused by restricted or damaged lines

• One waterline assembly with attached fittings as shown

• Shut off the home water supply and unplug the refrigerator before starting
• Tighten fittings to manufacturer torque—do not overtighten plastic fittings
• Inspect existing connections and replace any damaged shutoff valves or connectors
• After installation, turn water back on and check all connections for leaks; flush line per manufacturer instructions