Parts for Briggs & Stratton 150312-0112-E8: Air Cleaner, Controls, Exhaust System, Governor Spring, Ignition Parts

An air cleaner gasket is a valuable barrier between the carburetor of a machine and the air filter. This air cleaner gasket is made out of durable composite material. It is designed for use with outdoor lawn and garden power equipment such as lawn mowers, snowblowers, tillers, leaf blowers, and wood chippers. It is compatible with products by brands such as Briggs & Stratton, Toro, Cub Cadet, Snapper, and Simplicity.The air cleaner gasket part is crucial to the health and longevity of the machine's engine. The purpose of the air cleaner gasket is to help seal and protect the engine, the air cleaner, and other internal systems from dirt, contaminants, and debris that can often become the source of engine problems.The proper gasket for each user's engine depends entirely on the engine's design. That's why it is strongly recommended that users check their engine's Illustrated Parts List and refer back to their owner's manuals before making any decisions. This air cleaner gasket is an original OEM part sourced directly from the manufacturer, Midwest Engines. It is sold individually.

This filter is used for lawn and garden equipment. A dirty or clogged filter could cause the engine to run poorly.

This genuine OEM replacement part is a spark plug terminal for a wide variety of small combustion engines. In a combustion engine, the spark plug generates a small electrical charge that creates enough power to start up the ignition and engage combustion. The plug connects to the ignition through the terminal. Spark plugs generate and then pass a small electrical current through to the ignition. Usually, the main issue with spark plugs is that this current hyper-extends and ends up frying the spark plug. However, if the terminal is damaged, the charge will not pass into the ignitor, and the engine will not turn. If the spark plug can carry a charge but the engine still won't turn, it's likely the terminal that needs replacing. This is an easy repair because the terminal should just snap on and off. If stuck, a pair of needle-nose pliers should make it easier. This high-quality replacement part is compatible with engines from Murray, Toro, Lawn Boy, and Briggs & Stratton. It is sourced from the original manufacturer and ships individually.

This exhaust gasket is a genuine Midwest Engine replacement part for appliances that use small engines, such as chipper shredders, snowblowers, leaf blowers, and lawn mowers. The function of an exhaust gasket is to seal off the carburetor from the exhaust tube in order to protect the engine from the accumulation of dirt, debris, and gunk within the inner workings. The exhaust gasket may require replacement over time from general wear and tear. If the exhaust gasket is not sealing, allowing dirt and debris to accumulate within the carburetor and leaving the exhaust tube exposed, the part should be replaced immediately. Evidence of a damaged exhaust gasket could also manifest in the form of oil leakage, black smoke arising out of the exhaust tube, and unusually low pressure from the combustion when using the appliance. Any of these symptoms can be attributable to multiple factors, so one should assess if the exhaust gasket is responsible before ordering a replacement.This exhaust gasket is compatible with the following brands: Briggs and Stratton, Cub Cadet, Toro, and Simplicity. This part sold individually.

This is a foam pre-filter that is used to help prevent dust, pollen, and other debris from clogging the air filters of small engines. One of the most common problems faced by small engines is an inadequate air supply caused by air filters that have become mired with airborne debris. Cleaning or replacing filters can become a tiresome and expensive proposition. If filters are not adequately cared for, they perform poorly, waste gasoline, pollute the air, and cause internal engine damage. A good way to help an air filter do its job is by adding a foam pre-filter in the air filter compartment. Pre-filters are exposed to all the things that clog air intakes, so periodically, they also must be replaced. Foam pre-filters are designed to fit snugly inside the housing of the air filter of virtually all small engine housings. To install a pre-filter, remove the air filter housing by taking off the one screw holding it in place. Remove the air filter from the housing and place the pre-filter inside against the exterior wall of the housing with the arrows pointing up. Reinstall the air filter. The paper of the filter should fit perfectly against the labeled side of the pre-filter. Now simply reattach the air filter housing. Genuine Midwest Engine makes this OEM replacement part, and it is sold separately.

This is a genuine replacement for the air cleaner cover on select Briggs & Stratton engines. The air cleaner cover works with the air cleaner base assembly to provide a housing for the air filter. Over time, the cover and assembly can become cracked or damaged. This can affect the security of the air filter and also allow more debris to get into the engine. A cracked air cleaner cover could also lead to increased engine vibrations that could affect the filter and base. It is essential to replace this cover immediately in the event that it becomes damaged or broken. This air cleaner cover is a genuine OEM replacement that is manufactured to exact standards. It is designed to work with engines from Briggs & Stratton that are found on various pressure washers, including select models from the Vanguard brand. The cover is sold as an individual unit. Allow the engine to cool completely before beginning any repairs and protect the hands by wearing gloves.

This replacement part is a screw. It is a genuine replacement part made by Midwest Engine. Screws are found in many different types of appliances and machines. These parts are important in holding different pieces together so that the user is able to operate the appliance effectively. A replacement screw might be needed if some parts of the appliances are loose or missing. Screws can become stripped over time. If this is the case it is recommended that they be replaced as soon as possible. The repair for this screw is simple and will most likely require a screwdriver and perhaps pliers if the previous part is lodged in place. This screw is made of durable metal. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit. This is a genuine OEM replacement part.