Parts for Briggs & Stratton 19E417-1075-E1: Alternators, Engine / Valve Gasket Sets Parts

Prevents oil leaks around the crankshaft in small gas engines. Replace if oil seeps from the bottom of the engine. Verify fit with your model number.

Fix oil and coolant mixing or overheating with this engine cylinder head gasket. Seals combustion between block and head. Moderate DIY repair.

Fix exhaust leaks and pressure issues with this engine breather gasket. Creates a seal for proper gas flow and valve pressure regulation in lawn equipment.

This crankcase gasket is a genuine Midwest Engine part, sold individually. This crankcase gasket can be used as a replacement part in snowblowers, lawn mowers, and lawn tractors. The function of the crankcase gasket in these tools is to seal off the crankcase so that oil cannot leak out of it and dirt and debris cannot accumulate inside of it. A broken, malfunctioning, or loosened crankcase gasket can result in the accumulation of dirt, debris, and pebbles inside the crankcase and the crankshaft of outdoor appliances, which can cause damage to the engine; additionally, oil leakages can occur if the crankcase gasket is loose or damaged. If either of these symptoms is the case, this genuine OEM replacement part should be ordered immediately. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This crankcase gasket is compatible with the following brands: Midwest Engine, Briggs & Stratton, Toro, Simplicity, Cub Cadet, and Lawn Boy.

Seals space between engine components to prevent leaks. Replace if current gasket is missing, damaged, or causing oil/fuel leaks. Verify fit with your model.

Prevents oil leaks around the crankshaft in small gas engines. Replace if oil seeps from the bottom of the engine. Verify fit with your model number.

Seals air cleaner to protect your engine from dirt and debris. Replace if damaged, cracked, or causing poor performance. Confirm fit with model number.

This replacement exhaust gasket is an authentic OEM part for a snowblower or lawn tractor engine. On these appliances, the exhaust is located quite near to the air filter, meaning that there is a chance that exhaust could leak into the carburetor. The carburetor requires fresh air to oxygenate fuel for combustion, so manufacturers install a gasket to help seal off the exhaust. Once installed, gaskets exist under a lot of pressure and will absorb the heat of the engine. These stresses cause gaskets to slowly degrade and eventually break their seal. If the exhaust gasket blows, the engine will not perform as it should. Be cautious of a noisy engine that burns more fuel than usual and gives off a burning smell. These are signs that the exhaust gasket has given out. If so, use a socket wrench and wrench set to disassemble the blower and air filter housings, then remove the exhaust manifold and change out the broken gasket. This high-quality replacement exhaust gasket is compatible with engines made by Toro, Husqvarna, Briggs & Stratton, and Snapper. It comes sourced from the original manufacturer and ships individually.

No part of an engine is more elemental than the off/on switch. Briggs & Stratton manufacture this switch as a replacement part for more than 150 of their gasoline-powered motors, in particular on their gasoline-powered generators. As equipment that is intended to produce and maintain a great deal of power over several hours at a time, the internal connections of the generator can experience a lot of resistance, which means creating a lot of heat. The rotary off/on switch is a locus of much of that heat since it is the quick, safe way to stop the generator. As a result, the switch can be damaged by heat. Typically, the switch will reveal that it needs to be replaced by failing to remain in the on position. Replacing the rotary switch is a simple matter. Remove the plug cap and stabilize the generator so it cannot move during the procedure. Remove in order the starter rope, air filter assembly, electrical connection from cover, and four cover bolts. The old switch can be pinched out after disconnecting the ground wire. Reverse the order to install this new, OEM guaranteed replacement rotary off/on switch.