Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Washer Water Level Pressure Switch by Whirlpool

4.89 (64)
By: Whirlpool
Part Number: OEM18063390
Manufacturer Part Number: WPW10415587

This switch monitors water levels in the washing machine tub and signals when the correct amount has been reached. Located near the control panel or top of the washer, connected to a pressure tube. Replace when the washer overfills, underfills, or won't start filling with water.

More
$229.61

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Washer Water Level Pressure Switch (Part Number: OEM18063390)

View all Questions

Answer

Hello Jean & Howard,
The tech sheet says this about the F20 fault code:
If after 30 seconds not minimum 0.1l of water entered or maximum fill time of 13 minutes is exceeded, the valves will be turned off and the error code will be displayed. Press PAUSE/CANCEL twice to clear the display.
Possible Causes/Procedure
If there is no water in the unit:
Make sure that both valves at the water source(s) are turned on all the way.
Check for plugged or kinked inlet hoses or plugged screens in the inlet valves.
Verify inlet valve operation.
If there is water in the unit:
Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch.
Unplug washer or disconnect power.
Verify there is not a siphon problem.
Verify wire harness connections to inlet valves, pressure switch, flow meter, and Central Control Unit (CCU).
Check all hoses for possible leaks.
Plug in washer or reconnect power.
Verify pressure switch operation.
Verify flow meter operation by blowing air through the part and measuring the resistance.
Verify CCU operation by running a Diagnostic test or any cycle.
I have found that the flow meter fails very commonly. I would be very skeptical of it. As for your last question, the CCU is tested by running a diagnostic test. This is done as follows:
Starting Error History, Software Versions, and Diagnostic Test:
NOTE: Washer must be empty and the control must be in the OFF state.
Close the door.
Select any one key (except “Stop/Cancel and Control Lock
(EOC)) and follow the steps below, using the same key:
Press/hold for 2-5 sec
Press/hold for 2-5 sec
Press/hold for 2-5 sec
Press/hold for 2-5 sec
Press/hold for 2-5 sec.
Upon release, all yellow/green console LED lights will turn ON for 5 sec.
If there are any failure codes stored by the washer the display shows them.
Note: the last 4 errors will be displayed.
Press the same key to advance to the next code.
After the indication of error codes, the UI, CCU and MCU SW version will be displayed.
The number of cycles since last clean washer cycle is displayed.
All green console LED lights will turn ON for 5 seconds.
Next washer begins the automated diagnostic test.
To cancel out of service mode press “stop” button.

Read More...

Answered by AppliancePartsPros.com   |   Thursday, May 9, 2013

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro

Share your thoughts with other customers

Answer or comment
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google