Parts for Lg LWD3081ST/00: Assembly Parts

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This truss head tapping screw secures interior panels and small components on compatible appliances, restoring proper fit and stopping rattles or loose trim. It's a direct hardware replacement for a single mounting point. What it does:

• Fastens panels, brackets, and trim where a low-profile truss head is required
• Replaces missing or stripped screws that cause rattling or loose parts
• Provides a secure hold by forming threads in sheet metal during installation
• Useful for repairing cosmetic or functional panel alignment issues

• Disconnect power before working on any appliance to avoid shock or injury
• Use the correct sized Phillips or Torx driver to prevent cam-out or screw damage
• Start straight and thread slowly; do not overtighten to avoid stripping sheet metal
• Replace only with the exact part number for best fit and performance

This rear cover is the factory-style cabinet rear panel that protects internal components and helps maintain appliance structure. It restores the appliance's enclosure and keeps wiring and parts shielded for safe operation. What it does:

• Covers and protects internal components from dust, debris and accidental contact
• Helps reduce noise by enclosing moving parts and support structure
• Provides mounting surface for internal parts and routing for wiring
• Prevents exposure that can lead to sparks, shorting, or further component damage
• Common symptom: missing, cracked or loose rear cover, rattling or exposed components

• Disconnect power (unplug or switch off breaker) before starting any repair
• Use correct screws and fasteners; do not force or bend the panel into place
• Wear gloves to avoid cuts from sharp sheet-metal edges and check for pinched wiring after reassembly

This replacement shelf assembly restores a sturdy, level storage surface inside your refrigerator, helping you organize items and regain lost space when a shelf is cracked, missing, or no longer sits properly in its supports.

• Supports food containers and keeps items level within the compartment
• Slides into the side supports/rails for stable placement
• Replace if cracked, bowed, or unable to lock into position
• Common symptoms: broken or missing shelf, uneven seating, reduced storage capacity

• Remove items from the shelf area; lift out the damaged shelf
• Insert the new shelf into the side slots/rails and slide back until fully seated
• Ensure the shelf is level and locked into place before reloading items
• Handle edges carefully; avoid impact to prevent damage

This metal tray replaces a damaged or missing oven drip tray so you can catch spills and roast or bake without mess. It restores a stable cooking surface and helps protect the oven floor from food and grease. What it does

• Catches drips, crumbs and grease to make cleanup faster and prevent baked-on messes
• Provides a flat, stable surface for pans and bakeware
• Helps maintain even airflow around foods for consistent cooking results
• Replaces trays that are bent, corroded, pierced or missing

• One metal oven/drip tray

• Allow the appliance to cool completely and unplug or disconnect power before installing
• Slide the tray into the oven's lower rack supports until it rests securely
• Handle with care—edges may be sharp; use gloves if needed
• Clean before first use per the appliance owner's cleaning instructions

This replacement part is a slide rack that has been manufactured by LG and is compatible with wall ovens. The slide rack is an internal component of the oven that provides a stable, heat-safe surface on which to balance cookware and place food inside the oven. Over time, this part could become bent, dented, warped, corroded, lost, or broken, requiring replacement. No tools are required to replace this part. Simply slide out the old rack and slide the new one into place. Ensure that oven is completely cooled down before attempting this to prevent serious burn injuries. This is a genuine OEM part that has been sourced directly from the manufacturer. This is an authentic part made of high-quality, durable, non-corrosive metal and is compatible with different wall ovens manufactured by LG and other brands. This part is only sold individually.

This temperature sensor monitors internal appliance temperature and relays it to the electronic control so cycles run correctly. Replacing a faulty sensor restores accurate temperature feedback, helping the unit reach and maintain the set temperature.

• Detects temperature changes and sends a signal to the control board for proper operation
• Supports accurate heating/cooling and cycle timing based on real-time readings
• Direct replacement when the original reads open/short or out of range
• Common symptoms: incorrect temperatures, unusually long/short cycles, failure to reach set temperature, or sensor-related error codes

• Disconnect power before servicing and allow any hot components to cool
• Access the sensor, noting wire routing and connector orientation before removal
• Transfer any mounting clip/holder from the original if needed; seat the new sensor fully
• Route wiring away from moving or hot parts; restore power and run a test or cycle check