Attachment

This grease plug is a genuine OEM replacement part sourced directly from the manufacturer. It is found on snowblowers and other outdoor yard machines on the gearcase assembly, which houses the auger gear. The grease plug seals the oil port on the gearbox. This keeps lubrication inside the gearbox and is the access point for adding more when needed. If this plug is lost, the gearbox's oil could leak out, and contaminants could get into the gearbox.Lubricate the contents of the gearbox before installing the new grease plug. Locate and remove the two screws on the side to drain the gearbox. Install the grease plug in the bottom. Refill the oil using the vent hole. Continue filling until oil is coming out the top side screw. Close everything back up, and the machine is ready for use. To prepare the equipment for long storage, remove the grease plug and check the oil level. If it is not to the top, add more lubricant before sealing the grease plug.This grease plug is made of durable black molded plastic and is sold as an individual unit. It is compatible with snowblowers and snow throwers manufactured by Ryobi, MTD, Yard Machines, Troy-Bilt, Bolens, Yard-Man, Cub Cadet, and Husky.

This is a genuine replacement spindle assembly designed for use with select lawn mowers. The spindle assembly is responsible for securing the blade to the mower deck and ensuring that it rotates properly. if this assembly gets damaged or broken, it could result in the blade rotating unevenly or not rotating at all. This will result in an uneven lawn or the inability to use the mower until the part is replaced. This is an OEM spindle assembly designed by MTD and manufactured to exact standards. It is compatible with select models from the brand, along with some lawn mowers from Craftsman, Troy-Bilt, and Yard Man. It is sold as an individual part. Additional parts and hardware will require a separate purchase. It is important to disengage the engine before performing repairs on the mower deck. Allow the engine to cool and work in a well-ventilated area for safety. Always wear gloves for hand protection. To replace this part, the mower blades will have to be removed and replaced.

This snow thrower support bracket is an authentic OEM part sourced directly from the manufacturer for use on snow blowers. This bracket provides support to the discharge chute. If the bracket is worn or breaks, the chute may fall off the blower and snow will not discharge properly. If the support brackets are broken and the chute is not attached, the snow will blow out in in an undirected mess. Before the initial snow, regular maintenance and inspection of the snowblower will reveal any broken or worn parts. Before removing the old support bracket, park the snowblower on a flat surface and remove the spark plug. Remove the discharge chute to access the support bracket. Loosen the screws and remove the support bracket. Install the new support bracket with the screws from the original bracket. Reinstall the discharge chute.This snow thrower support bracket is a heavy-duty metal part that is individually sold. It is designed for use on snow blowers manufactured by MTD, Cub Cadet, and Troy-Bilt.

This screw is a genuine Midwest Engine replacement part for appliances operated by small engines, including lawn tractors, lawn mowers, snowblowers, leaf blowers, vacuums, and tillers. The purpose of a screw is to link materials together by piercing into the materials and then rotating it until the materials are firmly clasped together.It is likely that a screw will have to be replaced at some point in the lifespan of an appliance due to simply losing or misplacing the screw. If the materials that are generally supposed to be held together seem to be loosening or have come apart, it is likely that the screw has either fallen out or has undergone damage that has warped it. This kind of damage can be attributed to general overuse, to age, or simply to long-term exposure. If a screw is subject to any of this kind of damage, it is best to replace it immediately. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This screw is compatible with the following brands: MTD, Cub Cadet, Troy-Bilt, and Yard Machines. This part sold individually.

This part is a replacement hex bolt. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current hex bolt is defective or lost, this part can be used for repair or replacement. It is intended for use with outdoor power equipment.This replacement hex bolt is a standard piece of hardware named for its hexagonal shaped head. Bolts are essential for ensuring components are secured together sufficiently. They may corrode, rust, break, or become stripped over time and will thus require replacement. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this shaft attachment, the appropriate owner's manual and equipment diagrams should be referred to. This hex bolt is suitable for use on outdoor power equipment manufactured by MTD, Craftsman, Troy-Bilt, and other brands. It is a genuine OEM part and thus is made of high-quality, durable metal. Part sold individually.

The part listed is an MTD spiral axle. This spiral axle is designed for installation on certain snow-blowing machines. The spiral axle is the component that is attached to the auger of the snowblower. This part is the moving component that allows the auger to turn in a circular motion and dig into the snow to move it during use. If this part malfunctions, the snowblower will become unable to bore into the snow and properly loosen it for blowing and moving. Replacement should only be attempted for this component if there is background knowledge in the machine. The system around this part is made up of a complex series of pulleys, shafts, and belts. Removal and installation can be complex for an untrained user.This product is a genuine OEM part sourced directly from the manufacturer. This listing only includes the spiral axle and does not come with any other components or original machine. This part is compatible with MTD and Cub Cadet brands.

This replacement part is a hex nut. This is a genuine replacement part made by MTD. Hex nuts are small but important to the overall workings of many appliances. These parts work with other small pieces such as screws and washers to ensure that all parts of the machine are secure during use.A new hex nut might be needed if the current one is missing or damaged in any way. This can be caused by normal wear and tear with years of extended use. Hex nuts can experience large amounts of friction over time and may become stripped down. Be sure to replace the part as it might not be as effective as in prior uses. Refer to the user manual for specific directions on how to replace this part.This hex nut is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This replacement part is a sprocket assembly and is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This specific sprocket is most commonly found on chainsaws. A sprocket is an important part of any appliance with chains as the part uses several sprockets to engage the links of the chain so that it can move and turn properly. A new sprocket assembly might be needed if the user notices that the current chain is not able to stay in place or is coming off the track during use. Because of the nature of the sprocket it is not unusual for it to become stripped overtime and need to be replaced. Be sure to wear work gloves as this repair will take place close to the chain. This sprocket assembly is sold individually and is sourced directly from the manufacturer. This is also a genuine OEM replacement part.

This replacement part is a thrust collar. It is a genuine replacement part made by MTD. Thrust collars are small but important in many different types of machines and appliances. They are used to secure two different parts together.A new thrust collar might be needed if the user notices that the current one is damaged or missing. Due to the nature of this part, it is common that it can become stripped over time or misplaced from its position. Be sure to refer to the proper owner's manual for more details on how to replace this part. It is recommended that the user wear work gloves when replacing this part. This thrust collar is sold individually and is sourced directly from the manufacturer. This is also a genuine OEM replacement part to ensure proper fit and long-lasting use.