Parts for Troy-Bilt 10530: Auger Gear Box / Axle / Housing Parts

This is a genuine OEM gear housing assembly sourced directly from the manufacturer; it is used on snow blowers to protect the components in the gearbox. This solid metal housing prevents the components from being damaged by the elements, debris, and foreign objects. The gear housing assembly also keeps the internal components dry and lubricated by sealing lubricant in and keeping water out.Although the gear housing assembly is a heavy-duty metal part, it is possible that time, heavy use, and the elements can cause damage. If this is found during annual routine inspections, the gearbox housing should be removed and replaced. Before making this repair, remove the fuel from the snowblower and place the machine on a flat surface. Wear protective gloves and goggles. Keep a diagram of the machine nearby for reference as the machine is disassembled to access the gear housing assembly. After removing and replacing the gear housing assembly, reassemble the snowblower, and refill the gas. This gear housing assembly is made of heavy-duty metal and sold as an individual unit. It is compatible with snow blowers and snow throwers manufactured by Craftsman.

This replacement part is a housing assembly. It ensures that multiple parts are connected to allow for the engine to run smoothly and effectively during use. A new housing assembly might be needed if the current one is no longer able to stay attached to the machine. This can be due to normal wear and tear over time.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

This OEM screw is a fastener with a trimmed six-sided or hexagonal head plus a washer face on the bearing surface. It is one of the most commonly used fasteners. Considered standard hardware, this component has multiple applications and can be used on woodworking, machine assembly, and mechanical repair. The screw is 3/4 long and has a thread size of 5/16 -18. A hex cap screw is installed into tapped holes by turning the head to fit and tighten. This is the fastener of choice in applications where tight tolerance is necessary. This is a genuine factory part sourced from the manufacturer and is sold individually. It can be used with Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut brands of lawn maintenance equipment including lawn mowers, snowblowers, tillers, leaf blowers, log splitters, and wood chippers.

This replacement part is a drive shaft. This is a genuine replacement part made by MTD. Driveshafts are an important part of many different kinds of machinery. They often help transfer torque and engine rotation into the vehicle motion when the machine is shifted into drive. A new driveshaft might be needed if the user is unable to start or stop the vehicle. If the power in the movement of the machine is less than normal, be sure to replace the driveshaft as this might be the issue. It is recommended that the engine is completely turned off before attempting to replace this part. Work gloves are recommended when working with any type of part associated with the engine. This drive shaft is a genuine OEM replacement part to ensure proper fit. This part is sold individually and is sourced directly from the manufacturer.

This replacement part is a gear. This is a genuine replacement part made by MTD. This part is made with ridges that are able to connect to other parts so that they can turn or spin during use. This transfers energy and force to different pieces in the machine to ensure that the everything is working properly. A new gear might be needed if the current one is struggling to stay attached to other parts. This can be due to the ridges become stripped over time. If this is the case, the gear should be replaced. gears experience large amounts of friction and will need to be replaced after a while. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This oil seal is a genuine MTD part. It is designed as a replacement part for snowblowers. Oil seals do exactly what their name implies: they prevent oil from leaking. They are located on the input and output shafts of the crankshaft of the snowblower.It is not abnormal for oil seals to become worn over time, especially under heavy use. Users may notice oil leaking, especially while using the snowblower, if this is the case. Leaking oil can cause a mess (which can be dangerous) or may seriously damage the engine. Replacing an oil seal is a relatively simple repair, though some disassembly of the engine may be required. The oil seal itself is very small and round.This oil seal is a genuine OEM part sourced directly from the manufacturer, and it is sold individually. There is more than one oil seal on most snowblowers, so check them all before ordering. It is designed for compatibility with machines made by Craftsman, MasterCraft, White Outdoor, Columbia, Yard-Man, Cub Cadet, MTD, Yard Machines, and Troy-Bilt.

This grease plug is a genuine OEM replacement part sourced directly from the manufacturer. It is found on snowblowers and other outdoor yard machines on the gearcase assembly, which houses the auger gear. The grease plug seals the oil port on the gearbox. This keeps lubrication inside the gearbox and is the access point for adding more when needed. If this plug is lost, the gearbox's oil could leak out, and contaminants could get into the gearbox.Lubricate the contents of the gearbox before installing the new grease plug. Locate and remove the two screws on the side to drain the gearbox. Install the grease plug in the bottom. Refill the oil using the vent hole. Continue filling until oil is coming out the top side screw. Close everything back up, and the machine is ready for use. To prepare the equipment for long storage, remove the grease plug and check the oil level. If it is not to the top, add more lubricant before sealing the grease plug.This grease plug is made of durable black molded plastic and is sold as an individual unit. It is compatible with snowblowers and snow throwers manufactured by Ryobi, MTD, Yard Machines, Troy-Bilt, Bolens, Yard-Man, Cub Cadet, and Husky.

This grease fitting attaches to the cast pivot bar on many types of garden and lawn equipment. It is made of durable metal and ensures that internal parts of the equipment are lubricated so they operate at their full potential. Sometimes a grease fitting can become worn damaged and need to be replaced.If a lawn tool no longer seems to be properly lubricated, the grease fitting could be the cause. A pair of pliers will be required to make the replacement. Clean the area near the grease fitting and then use a hex wrench to remove it from the machine. Take the new fitting and place it into the hole and tighten it before applying grease.This is a genuine OEM replacement grease fitting that is sourced directly from the manufacturer. The part is sold individually. The fitting is compatible with chipper shredders, lawn tractors, snowblowers, string trimmers, edgers, chainsaws, and lawnmowers manufactured by Yard-Man, Cub Cadet, Troy-Bilt, Craftsman, Ryobi, Murray, Broan, Yard Machines, Huskee, Montgomery Wards, Bolens, MasterCut, and MTD.

This part is a replacement thrust bearing. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. It is intended to replace a broken or defective thrust bearing in outdoor power equipment.Bearings help to reduce friction created by moving parts as well as ensure the equipment functions smoothly and without excessive vibration. Bearings can become worn, corroded, jammed, or otherwise defective, requiring replacement. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to use this thrust bearing, the appropriate owner's manual and equipment diagrams should be referred to. This thrust bearing is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment models that have been manufactured by MTD, Craftsman, and other brands.

This sleeve is a genuine MTD part. It is a replacement part for snow blowers and snow throwers primarily, but is also sometimes utilized on other small engine lawn equipment.Sleeve bearings are very important as they help with linear movements between two parts. They do this by absorbing the friction created by the two other parts, which reduces noise and vibrations. It is normal for them to wear out over time. Increased noise is one way to recognize this problem.This sleeve bearing is a genuine OEM part sourced directly from the manufacturer. It is sold individually. Some machines require more than one sleeve bearing. It is compatible with equipment made by White Outdoor, Craftsman, Mastercraft, Columbia, MTD, Troy-Bilt, Cub Cadet, Yard Machines, Yard-Man, and others.