Parts for Frigidaire FCRG3052ABE: Backguard Parts

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

This small protective cap covers and protects exposed appliance hardware, keeping dirt and moisture out while preventing accidental contact. It's a simple replacement that restores a finished appearance and helps maintain part integrity. What it does:

• Covers and protects an exposed shaft, tab, or fastener from debris and wear
• Helps prevent accidental contact with sharp or moving parts
• Restores the finished look of the appliance where the original cap was lost or damaged
• Simple, passive part—no electrical or mechanical function to reconfigure

• One replacement protective cap

• Always unplug the appliance or disconnect power before servicing
• Remove the damaged cap by hand or with a gentle pry tool; press the replacement into place until fully seated
• Small part—keep away from children and pets; loss is common during disassembly

A replacement black control panel overlay that restores the appliance's front finish and control markings for clear, reliable operation. Replaces a worn, cracked, or faded overlay to return a clean, readable control surface. What it does:

• Covers and protects the appliance's control area and printed labels
• Restores legible button graphics and display openings
• Replaces cracked, peeling, or discolored overlays that affect appearance or usability
• Helps prevent dirt and moisture from contacting underlying controls

• Disconnect power to the appliance before beginning any service
• Remove trim or control housing to access the overlay
• Carefully peel or unfasten the old overlay and align the new overlay before securing
• If adhesive or retainers are used, replace with manufacturer-specified parts and follow torque/fastening guidance

The Control Board is an OEM part for Frigidaire wall ovens and ranges. As the central processing component, it controls critical functions including temperature regulation, cooking modes and timer programming.

Causes can involve regular wear over multiple heating cycles, exposure to moisture or direct power fluctuations over time.

Symptoms of a faulty control board include:

• Inability to adjust or maintain set oven temperatures
• Failures in convection, broil or bake elements cycling on/off
• Non-functional timer, clock or display screens
• Error codes or safety lockouts appearing

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Color: White

The Knob is an OEM part for Frigidaire ranges. It is located on the front control panel and facilitates setting the exact temperature or heat level for cooking. Each individual knob directly corresponds to a specific burner or oven function.

Causes stem from natural wear through frequent manual operation. Harsh cleaning chemicals or accidental impacts can also damage knob surfaces or mechanics over time.

Symptoms of a bad knob can include:

• Looseness making it difficult to turn 
• Becoming illegible with labels fading 

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.