Parts for Frigidaire FFIF3054TSA: Backguard Parts

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

This small protective cap covers and protects exposed appliance hardware, keeping dirt and moisture out while preventing accidental contact. It's a simple replacement that restores a finished appearance and helps maintain part integrity. What it does:

• Covers and protects an exposed shaft, tab, or fastener from debris and wear
• Helps prevent accidental contact with sharp or moving parts
• Restores the finished look of the appliance where the original cap was lost or damaged
• Simple, passive part—no electrical or mechanical function to reconfigure

• One replacement protective cap

• Always unplug the appliance or disconnect power before servicing
• Remove the damaged cap by hand or with a gentle pry tool; press the replacement into place until fully seated
• Small part—keep away from children and pets; loss is common during disassembly

This control panel overlay is the printed graphic that covers a range or oven control panel, restoring clear labels and the original appearance for safe, intuitive operation. What it does:

• Replaces faded, scratched, or peeling control graphics so settings and icons are readable
• Protects the underlying control surfaces from spills, grease, and light abrasion
• Helps make button and touch areas easier to find and use after wear
• Improves appliance appearance when the existing overlay is damaged or discolored

• Disconnect power to the appliance before starting any work
• Remove the control panel or trim to access the overlay
• Clean and dry the panel surface thoroughly before installing the new overlay
• Align carefully during installation to avoid air bubbles; use manufacturer-recommended adhesive/fasteners if required

The Control Board is an OEM part for Frigidaire ranges. As the "nerve center" of the appliance, it oversees critical functions like temperature regulation of oven/burners, timed cooking features, and system diagnostics through electronic control circuits. 

Causes of a bad control board can include moisture over years of use corroding circuitry connections, failure of individual electronic components due to continuous thermal cycling, and damage from power surges overloading boards.

Symptoms of a faulty control board include: 

• Burners or ovens failing to ignite or maintain proper flames
• Inability to select or activate cooking functions from controls  
• Sensor or calibration errors displayed on the range display
• Random shutoffs or issues holding programmed cooking times

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This mounting bracket secures internal appliance components and helps keep panels and assemblies aligned for reliable operation. It provides a simple replacement option when original fasteners or supports become bent or broken. What it does

• Supports and positions internal panels or components to prevent sagging or misalignment
• Restores secure attachment when original bracket is cracked, bent, or missing
• Helps reduce rattling or vibration caused by loose assemblies
• Compatible with models that use this OEM-style mounting bracket

• Disconnect power and water before starting any repair
• Inspect adjacent fasteners and clips; replace if worn or damaged
• Basic hand tools are normally required; avoid overtightening screws

This mounting/support bracket secures internal components and panels to restore proper alignment and reduce movement. It replaces a worn or broken bracket so doors, panels, or internal assemblies fit securely and operate smoothly. What it does:

• Provides a stable anchor point for panels or internal assemblies to prevent sagging or misalignment
• Stops shifting or rattling caused by a loose or broken bracket during operation
• Helps maintain proper spacing so doors and panels open and close correctly
• Supports attached components to reduce wear on fasteners and adjacent parts

• Disconnect power before beginning any repair to avoid electrical shock
• Installation requires basic hand tools; retain original fasteners unless replacement fasteners are specified
• Inspect surrounding mounting points and replace any damaged clips or screws for a secure fit

This snap-in plug seals a small cabinet or component opening to keep out moisture, debris and pests while preserving a finished appearance. It's a simple, low-cost replacement that restores proper sealing and fit. What it does

• Seals unused holes or access openings to prevent water, dust and pests from entering
• Restores a finished look where trim or panels have a missing cap
• Helps stop rattles from loose openings and reduces airflow where needed
• Works as a direct-fit replacement when the original plug is damaged or lost

• One snap-in plug

• Remove surrounding trim or panel per your model's service instructions to access the opening
• Press the plug into the hole until it snaps fully into place; no special tools normally required
• Always disconnect power to the appliance before doing any service that requires panel removal

This replacement shield protects internal components and helps maintain proper alignment where it mounts, restoring fit and reducing rattles or rubbing. It's a direct-fit exterior/interior mounting shield for affected appliance areas. What it does

• Covers and protects wiring, seals, or fasteners from contact and debris
• Maintains proper part alignment to prevent rubbing or misalignment noises
• Stops small objects from entering sensitive areas behind panels
• Worn, cracked, or missing shields can allow vibration, noise, or visible gaps

• Disconnect power (unplug or shut off breaker) before starting any repair
• Basic hand tools typically required; keep track of fasteners during removal
• Inspect surrounding clips, screws, and seals and replace if damaged

This replacement shield is a molded protective trim piece that helps cover and protect internal components while keeping the cabinet interior tidy. It restores the original fit and helps prevent contact damage or debris buildup. What it does:

• Covers and protects wiring, connectors, and nearby components from accidental contact or damage
• Helps keep interior surfaces clean by blocking debris and splashes from reaching sensitive parts
• Maintains correct spacing/fit of the surrounding trim for a finished appearance
• Supports proper airflow clearance where applicable to help consistent cooling performance

• One replacement shield

• Disconnect power to the appliance before starting any repair
• Remove any trim or fasteners that obstruct the old shield; save screws if reusing
• Align the new shield in the same orientation as the old piece and secure with the original fasteners
• Handle carefully to avoid cracking the plastic; do not force into place

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.